American Boat and Yacht Council (ABYC)

3069 Solomon's Island Road, Edgewater, MD 21037

Publication	CFR Reference
A–1–93—Marine Liquified Petroleum Gas (LPG) Systems	121.240
A–3–93—Galley Stoves	121.200 129.550
A–7–70—Boat Heating Systems	121.200 129.550
A–22–93—Marine Compressed Natural Gas (CNG) Systems	121.240
E–1–72 Bonding of Direct Current Systems	129.120
E–8 1994 Alternating Current (AC) Electrical Systems on Boats	129.120
E–9 1990 Direct–Current (DC) Electrical Systems on Boats	129.120
H–25–94—Portable Gasoline Fuel Systems	119.458
P–1–93—Installation of Exhaust Systems for Propulsion and Auxiliary Engines	116.405 119.425 119.430

American Bureau of Shipping

Publications Department, ABS Plaza, 16855 Northchase Drive, Houston, Texas 77060

Publication	CFR Reference
Guide for Building and Classing High–Speed Craft, February, 1997	114.600 116.300
Rules for Building and Classing Mobile Offshore Drilling Units, 1980	108.113 108.705
Rules for Building and Classing Mobile Offshore Drilling Units, 1994	110.10-1 111.12-1(a) 111.12-3 111.12-5 111.12-7 111.33-11 111.35-1 111.70-1(a)
Rules for Building and Classing Mobile Offshore Drilling Units, 1998	107.205(b)
Rules for Building and Classing Aluminium Vessels, 1975	116.300, 127.210
Rules for Building and Classing Steel Vessels, 1981	90.35-1 91.15-1 92.01-10
Rules for Building and Classing Steel Vessels, 1995	110.10-1 110.15-1 111.12-1(a) 111.12-3 111.12-5 111.12-7 111.33-11 111.35-1 111.70-1(a) 111.105-39(a) 111.105-40(a) 111.105-47(a) 113.05-7 119.410 120.360 127.210 129.360
Rules for Building and Classing Steel Vessels, 1996	91.15-5(b) 110.15-1 111.01-9 111.12-1(a) 111.12-3 111.12-5 111.12-7 111.33-11 111.35-1 111.70-1(a) 111.105-31(n) 111.105-39(a) 111.105-40(a) 113.05-7
Rules for Building and Classing Steel Vessels, 1998	91.15-5(b)
Rules for Building and Classing Steel Vessels Under 61 Meters (200 Feet) in Length, 1983	116.300 127.210
Rules for Building and Classing Steel Vessels for Service on Rivers and Intracoastal Waterways, 1995	116.300
Rules for Building and Classing Mobile Offshore Drilling Units, 1994	133.140 133.150
U.S. Supplement to ABS Rules for Mobile Offshore Drilling Units, November 1, 1998	107.205(b)
U.S. Supplement to ABS Rules for Steel Vessels for Vessels on International Voyages, October 21, 1996	91.15-5(b)
U.S. Supplement to ABS Rules for Steel Vessels for Vessels on International Voyages, August 1, 1997	91.15-5(b)

American National Standards Institute (ANSI)

25 West 43rd Street, Fourth floor, New York, NY 10036 Telephone: (212) 642–4900

Publication	CFR Reference
ANSI Z89.1–1969 Industrial Head Protection	108.497
ANSI A14.3–1974 Fixed Ladders	108.160
ANSI/ASME A17.1 Safety Code for Elevators and Escalators, 1993	110.10-1 111.91-1
ANSI/ASME A17.1A Addenda to ANSI/ASME A–17–1 Safety Code for Elevators and Escalators (including Errata, 1995), 1994	110.10-1 111.91-1
ANSI/IEEE C37.04–79 Rating Structure for AC High–Voltage Circuit Breakers Rated on a Symmetrical Current Basis	110.10-1 111.54-1
ANSI C37.12 For AC High–Voltage Circuit Breakers Rated on a Symmetrical Current Basis–Specification Guide, 1991	110.10-1 111.54-1(c)
ANSI C37.14–79 Low–Voltage DC Power Circuit Breakers Used in Enclosures	111.54-1(c)(2)
ANSI A17.1–1984, including supplements A17.1a–1985 and A17.1b–1985—Safety Code for Elevators and Escalators	120.540
ANSI B31.1—1986—Code for Pressure Piping, Power Piping	119.710 128.240
ANSI Z26.1–1977, including 1980 supplement—Safety Glazing Materials For Glazing Motor Vehicles Operating on Land Highways	116.1030 127.430

American Petroleum Institute

1220 L Street NW., Washington, DC 20005–4070; Telephone: (202) 682–8000

Publication	CFR Reference
API RP2D with supplement 1—Recommended Practice for Operation and Maintenance of Offshore Cranes, 1972	107.259 109.437 109.521 109.527
API Spec 2C, 2nd Ed. with supplement 2 Specification for Offshore Cranes, 1972	107.309 108.601 109.437

American Society of Mechanical Engineers

Three Park Avenue, New York, NY 10016–5990; Telephone: (800) THE–ASME

Publication	CFR Reference
ASME Boiler and Pressure Vessel Code Section V, Nondestructive Examination (1986)	98.01-3
ASME Boiler and Pressure Vessel Code, Section 1, Power Boilers, July 1989 w/1989 addenda	128.240

American Society for Nondestructive Testing (ASNT)

P.O. Box 21142, Columbus, OH 43221

Publication	CFR Reference
Recommended Practice No. SNT–TC–1A (1988), Personnel Qualification and Certification in Nondestructive Testing	98.01-3

American Society for Testing and Materials

100 Barr Harbor Drive, West Conshohocken, PA, 19428–2959, Telephone (610) 832–9585, FAX (610) 832–9555

Publication	CFR Reference
ASTM B 96–93, Standard Specification for Copper–Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General Purposes and Pressure Vessels	114.600 119.440
ASTM B 117–73 (Reapproved 1979)—Method of Salt Spray (Fog) Testing	114.400
ASTM B 117–95 Standard Practice for Operating Salt Spray (FOG) Apparatus	110.10-1 110.15-1(b)
ASTM B 117–97, Standard Practice for Operating Salt Spray (Fog) Apparatus	110.10-1 110.15-1 114.400 114.600
ASTM B 122/B 122 M–95, Standard Specification for Copper–Nickel–Tin Alloy, Copper–Nickel–Zinc Alloy (Nickel Silver), and Copper–Nickel Alloy Plate, Sheet, Strip, and Rolled Bar	114.600 119.440
ASTM B 127–98, Standard Specification for Nickel–Copper Alloy (UNS NO4400) Plate, Sheet, and Strip	114.600 119.440
ASTM B 152–97a, Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar	114.600 119.440
ASTM B 209–96, Standard Specification for Aluminum and Aluminum–Alloy Sheet and Plate	114.600 119.440
ASTM D 93–80 Standard Test Methods for Flash Point by Pensky–Martens Closed Cup Tester	128.310
ASTM D 93–94 Flash Point by Pensky–Martens Closed Cup Tester	114.400
ASTM D 93–94, Flash Point by Pensky–Martens Closed Cup Tester	108.101 108.500
ASTM D 93–97, Standard Test Methods for Flash Point by Pensky–Martens Closed Cup Tester	97.01-2 97.15-55 108.101 108.500 114.400 114.600 125.180 128.310
ASTM D 323–94, Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method)	105.01-3 105.10-15
ASTM D 635–91 Rate of Burning and/or Extent and Time of Burning of Self–Supporting Plastics in a Horizontal Position	119.440
ASTM D 635–97, Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position	114.600 119.440
ASTM D 789–78 Standard Specification for Nylon Injection Molding and Extrusion Materials	111.60-1(b)(4)
ASTM D 2863–91 Measuring the Minimum Oxygen Concentration to Support Candle–like Combustion of Plastics (Oxygen Index)	119.440
ASTM D 2863–95, Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle–like Combustion of Plastics (Oxygen Index)	114.600 119.440
ASTM D4066–94b Standard Specification for Nylon Injection and Extrusion Materials (PA), 1994	110.10-1 111.60-1(c)
ASTM D 4066–96a, Standard Classification System for Nylon Injection and Extrusion Materials (PA)	110.10-1 111.60-1
ASTM E 84–94 Surface Burning Characteristics of Building Materials	114.400 116.422 116.423
ASTM E 84–98, Standard Test Method for Surface Burning Characteristics of Building Materials	114.600 116.405 116.422 116.423
ASTM E 648–94a Critical Radiant Flux of Floor–Covering Systems Using a Radiant Heat Energy Source	114.400 116.423
ASTM E 648–97, Standard Test Method for Critical Radiant Flux of Floor–Covering Systems Using a Radiant Heat Energy Source	114.400 114.600 116.423
ASTM E 662–94a Specific Optical Density of Smoke Generated by Solid Materials	114.400 116.423
ASTM E 662–97, Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials	114.400 114.600 116.423
ASTM F 1014–86 Standard Specification for Flashlights on Vessels	94.20-15(j) 96.35-3(c) 108.497(b)
ASTM F 1014–92, Standard Specification for Flashlights on Vessels	96.01-3 96.35-5 108.101 108.497
ASTM F 1121–87 International Shore Connections for Marine Fire Applications	95.10 108.427
ASTM F 1121–87 (1993), Standard Specification for International Shore Connections for Marine Fire Applications	95.01-2 95.10-10 108.101 108.427
ASTM F 1196–89 Sliding Watertight Door Assemblies	92.01
ASTM F 1197–89 Sliding Watertight Door Control Systems	92.01
ASTM Adjunct F 1626 Symbols for Use in Accordance with Regulation II–2/20 of the 1974 SOLAS Convention As Amended PCN: 12–616260–01 (1996)	97.01-2 97.36-1
ASTM Adjunct F 1626 Symbols for Use in Accordance with Regulation II–2/20 of the 1974 SOLAS Convention As Amended PCN: 12–616260–01 (1996)	109.105 109.563

Coast Guard

Commandant [G–MVI], 2100 2nd St. SW., Washington, DC 20593

Publication	CFR Reference
160.014—“Compass and Mounting dated Dec. 14, 1944” (Specification for Compasses: Magnetic, Liquid–filled, Mariners Compensating, for Lifeboats (with mounting) for Merchant Vessels), 1944	94.20-15

Department of Defense

DODSSP Standarization Document Order Desk, 700 Robbins Ave., Bldg. 4D, Philadelphia, PA 19111–5098

Publication	CFR Reference
ZZ–H–451 Hose, Fire, Woven–jacketed Rubber or Cambric–Lined, with Couplings, F	95.10-10 108.425
MIL–C–915E–1972 (with 1980 Amend) Cable and Cord, Electrical, for Shipboard Use	111.60-1(a) 111.60-13(a)(4)
MIL–C–24640A Military Specification Cables, Light Weight, Electric, Low Smoke, For Shipboard Use, General Specification For, 1995	110.10-1 111.60-1(a) 111.60-3(c)
MIL–C–24643A Military Specification Cables and Cords, Electric, Low Smoke, For Shipboard Use, General Specification for, 1994 (incl. Amendment 1)	110.10-1 111.60-1(a) 111.60-3(c)
MIL–M–15562F–1977 Matting or Sheet, Floor Covering, Insulating for High Voltage Application	111.30-11
MIL–W–76D Military Specification Wire and Cable, Hook–up, Electrical, Insulated, General Specification for, 1992	110.10-1 111.60-11(c)
MIL–W–16878F Military Specification Wire, Electrical Insulated, General Specification for, 1982	110.10-1 111.60-11(c)
MIL–HDBK–299 (SH) Military Handbook Cable Comparison Handbook Data Pertaining to Electric Shipboard Cable, 1989	110.10-1 111.60-3(c)
DDS 300–2 °C. Fault Current Calculations, 1988	110.10-1, 111.52-5
DDS 304–2–1974 Electrical Cables, Ratings, and Characteristics	111.60-1(a)(3)
DDS 9620–3–1962 AC Fault Current Calculations	111.52-5(b)

Instrument Society of America

400 Stanwix St., Pittsburgh, PA 15222

Publication	CFR Reference
RP 12.6–1976 Installation of Intrinsically Safe Instrument Systems in Class I Hazardous Locations	111.105-15(b)(2)

International Association of Drilling Contractors (IADC)

PO Box 4287, Houston, TX 77210–4287

Publication	CFR Reference
IADC–DCCS–1/1991, Guidelines for Industrial System DC Cable for Mobile Offshore Drilling Units, 1991	110.10-1 111.60-1(f)

International Electrotechnical Commission (IEC)

Bureau Central de la Commission Electrotechnique Internationale, 3 rue de Varembe, Geneva, Switzerland

Publication	CFR Reference
IEC 56, High–voltage alternating–current circuit breakers, Fourth Edition, 1987 (Including Amendment 1,1992; Amendment 2, 1995; and Amendment 3, 1996)	111.54-1
IEC 68–2–52, Basic Environmental Testing Procedures, Part 2: Tests. Test KB: Salt Mist, Cyclic (Sodium Chloride Solution), 1984	110.10-1 110.15-1(b)
IEC 79–0, Electrical Apparatus for Explosive Gas Atmospheres, Part 0: General Requirements, 1983 (including Amendment 2, 1991)	110.10-1 111.105-1 111.105-3 111.105-5 111.105-7 111.105-15(b) 111.105-17(b)
IEC 79–1, Electrical Apparatus for Explosive Gas Atmospheres, Part 1: Construction and Test of Flameproof Enclosures of Electrical Apparatus, 1990 [including First Supplement to the Second edition (1971), 1975 and Amendment 1 to the Third edition (1990), 1993]	110.10-1 111.105-3 111.105-5 111.105-9 111.105-15(b) 111.105-17(b)
IEC 79–2, Electrical Apparatus for Explosive Gas Atmospheres, Part 2: Electrical Apparatus—Type of Protection “p”, 1983	110.10-1 111.105-3 111.105-5 111.105-7(b) 111.105-15(b) 111.105-17(b)
IEC 79–5, Electrical Apparatus for Explosive Gas Atmospheres, Part 5: Sand–Filled Apparatus. First Edition (1967) Incorporating the First Supplement, (1969)	110.10-1 111.105-3 111.105-5 111.105-15(a) 111.105-15(b) 111.105-17(b)
IEC 79–6, Electrical Apparatus for Explosive Gas Atmospheres, Part 6: Oil–Immersion “o”, 1995	110.10-1 111.105-3 111.105-5 111.105-15(a) 111.105-15(b) 111.105-17(b)
IEC 79–7, Electrical Apparatus for Explosive Gas Atmospheres, Part 7: Increased Safety “e”, 1990 (including Amendment 1, 1991 and Amendment 2, 1993)	110.10-1 111.105-3 111.105-5 111.105-15(a) 111.105-15(b) 111.105-17(b)
EC 79–11, Electrical Apparatus for Explosive Gas Atmospheres, Part 11: Intrinsic Safety “I” 1991	110.10-1 111.105-3 111.105-5 111.105-11(a) 111.105-15(b) 111.105-17(b)
IEC 79–15, Electrical Apparatus for Explosive Gas Atmospheres, Part 15: Electrical Apparatus with Type of Protection “n”, 1987	110.10-1, 111.105-3 111.105-5 111.105-15(a) 111.105-15(b) 111.105-17(b)
IEC 79–18, Electrical Apparatus for Explosive Gas Atmospheres, Part 18: Encapsulation “m”, 1992	110.10-1 111.105-3 111.105-5 111.105-15(a) 111.105-15(b) 111.105-17(b)
IEC 92–3, Electrical Installation In Ships, Part 3: Cables (construction, testing and installations) Second Edition, 1965 as amended through August, 1994	110.10-1 111.05-7 111.60-1(a) 111.60-3(a) 111.60-3(c) 111.81-1(d)
IEC 92–101, Electrical Installations in Ships, Part 101: Definitions and General Requirements, 1994 (including Amendment 1, 1995)	110.10-1 110.15-1(a) 111.81-1(d)
IEC 92–201, Electrical Installations in Ships, Part 201: System Design—General, 1994	110.10-1 111.70-3(a) 111.81-1(d)
IEC 92–202, Electrical Installations in Ships, Part 202: System Design—Protection, 1994	110.10-1 111.50-3(c) 111.50-3(e) 111.50-3(g) 111.53-1(a) 111.54-1(a) 111.81-1(d)
IEC 92–301, Electrical Installations in Ships, Part 301: Equipment—Generators and Motors, 1980 (including Amendment 1, 1994, and Amendment 2, 1995)	110.10-1 111.25-5(a) 111.70-1(a) 111.81-1(d)
IEC 92–302, Electrical Installations in Ships, Part 302: Equipment—Switchgear and Controlgear Assemblies, 1980 (including Amendment 1, 1989 and Amendment 2, 1994)	110.10-1 111.30-1 111.30-5(a) 111.30-19(a) 111.81-1(d)
IEC 92–303, Electrical Installations in Ships, Part 303: Equipment—Transformers for Power and Lighting, 1980	110.10-1 111.20-15 111.81-1(d)
IEC 92–304, Electrical Installations in Ships, Part 304: Equipment—Semiconductor Convertors, 1980 (including Amendment 1, 1995)	110.10-1 111.33-3(a) 111.33-5(b) 111.81-1(d)
IEC 92–306, Electrical Installations in Ships, Part 306: Equipment—Luminaires and Accessories, 1980	110.10-1 111.75-20(a) 111.81-1(d)
IEC 92–350, Electrical Installations in Ships, Part 350: Low–voltage Shipboard Power Cables—General Construction and Test Requirements, 1988, Amendment 1 (1994)	110.10-1 111.60-1
IEC 92–352, Electrical Installations in Ships, Part 352: Choice and Installation of Cables for Low–Voltage Power Systems, 1979, (with Amendment 1, 1987 and Amendment 2, 1994)	110.10-1 111.60-3(a) 111.60-3(c) 111.60-5 111.81-1(d)
IEC 92–353, Electrical Installations in Ships, Part 353: Single and Multicore Non–radial Field Power Cables with Extruded Solid Insulation for Rated Voltages 1kV and 3kV (1995–01) Second edition	110.10-1 111.60-1 111.60-3
IEC 92–401, Electrical Installations in Ships, Part 401: Installation and Test of Completed Installation, 1980	111.05-9
IEC 92–501, Electrical Installations in Ships, Part 501: Special Features—Electric Propulsion Plant, 1984	110.10-1 111.81-1(d)
IEC 92–502, Electrical Installations in Ships, Part 502: Tankers—Special Features, 1994	110.10-1 111.81-1(d) 111.105-31(e)
IEC 92–503, Electrical Installations in Ships, Part 503: Special Features—A.C. Supply Systems with Voltages in the Range Above 1KV up to and including 11KV, 1975	110.10-1 111.30-5(a) 111.81-1(d)
IEC 92–504, Electrical Installations in Ships, Part 504: Special Features—Control and Instrumentation, 1994	110.10-1 111.81-1(d)
IEC 331, Fire Resisting Characteristics of Electric Cables, 1970	110.10-1 113.30-25(i)
IEC 332–1, Tests on Electric Cables Under Fire Conditions, Part 1: Test on a Single Vertical Insulated Wire or Cable, 1993	110.10-1 111.30-19(b)
IEC 332–3, Tests on Electric Cables Under Fire Conditions, Part 3: Test on bunched wires or cables, 1992	110.10-1 111.60-1(b) 111.60-2 111.60-6(a) 111.107-1(c)
IEC 363, Short–Circuit Current Evaluation with Special Regard to Rated Short–Circuit Capacity of Circuit–Breakers in Installations in Ships, 1972	110.10-1 111.52-5(c)
IEC 529, Degrees of Protection Provided by Enclosures (IP Code), 1989	110.10-1 111.01-9(a) 111.01-9(b) 111.01-9(c) 111.01-9(d) 111.01-9(Note) 113.10-7 113.20-3 113.25-11 113.30-25(c) 113.30-25(h) 113.40-10(b)
IEC 533, Electromagnetic Compatibility of Electrical and Electronic Installations in Ships, 1977	110.10-1 113.05-7
IEC 947–2, Low–Voltage Switchgear and Controlgear, Part 2: Circuit Breakers, 1989 (including Amendment 1, 1992 and Amendment 2, 1993)	110.10-1 111.54-1(b) 111.54-1(c)

Institute of Electrical and Electronics Engineers

Service Center, 445 Hoes Lane, Piscataway, NJ 08855 Telephone: (800) 678–4333

Publication	CFR Reference
Standard 45–1977 Recommended Practice for Electrical Installations on Shipboard	120.340 125.180
IEEE C 37.13 IEEE Standard for Low–Voltage AC Power Circuit Breakers Used in Enclosures, 1990	111.54-1(c)
No. 27–1974 Switchgear Assemblies Including Metal–Enclosed Bus (ANSI/IEEE C 37.20–69 and Supplements)	110.30-23
IEEE Std C37.14 IEEE Standard for Low–Voltage DC Power Circuit Breakers Used in Enclosures, 1992	110.10-1 111.54-1(c)

Institute of Electrical and Electronic Engineers (IEEE)

Service Center, 445 Hoes Lane, Piscataway, NJ 08855 Telephone: (800) 678–4333

Publication	CFR Reference
IEEE Std 45–1983 IEEE Recommended Practice for Electric Installations on Shipboard, 1983	110.10-1 111.05-7 111.15-2(b) 111.30-1 111.30-5(a) 111.30-19(a) 111.33-3(a) 111.33-5(a) 111.40-1 111.60-1(a) 111.60-2 111.60-3 111.60-5(a) 111.60-6(a) 111.60-11(c) 111.60-13(a) 111.60-19(b) 111.60-21 111.75-5(b) 111.105-3 111.105-31(e) 111.105-41 111.107-1(c) 113.65-5
IEEE Std 100–1992 The New IEEE Standard Dictionary of Electrical Terms, 1992	110.10-1 110.15-1(a)
IEEE Std 320 Application Guide for AC High–Voltage Circuit Breakers Rated on a Symmetrical Current Basis (ANSI/IEEE C37.010–79), 1979	111.54-1(c) 110.10-1
IEEE Std 331 Application Guide for Low–Voltage AC Non–Integrally Fused Power Circuit Breakers (Using Separately Mounted Current–Limiting Fuses) (ANSI C37.27), 1987	111.54-1(c) 110.10-1
IEEE Std 383–1974 IEEE Standard for Type Test of Class IE Electric Cables, Field Splices, and Connections for Nuclear Power Generating Stations, 1974	110.10-1 111.107-1(c)
No. 538–1976 Low–Voltage AC Integrally Fused Power Circuit Breakers (ANSI C37.13a–1975)	111.54-1(c)(1)(ii) 111.57-1 (Note)
IEEE Std 1202–1991 IEEE Standard for Flame Testing of Cables for Use in Cable Tray in Industrial and Commercial Occupancies, 1991	110.10-1 111.60-2 111.60-6(a)

International Maritime Organization (formerly Inter–Governmental Maritime Organization)

4 Albert Embankment, London SE1 7SR, England Telephone: 0171–587 3210; FAX: 0171–587 3210; Telex: 23588. Purchase from: IMO Sales, New York Nautical Instrument and Service Corp., 140 W. Broadway, New York, NY 10013. Telephone: (212) 962–4522; FAX: (212) 406–8420

Publication	CFR Reference
Resolution A.264 (VIII)—Carriage of Grain, 1973	93.20-05
Resolution A.654 (XVI) Graphical Symbols for Fire Control Plans, October 19, 1989	97.01-2 97.36-1
Resolution A.520(13), Code of Practice for the Evaluation, Testing and Acceptance of Prototype Novel Life–saving Appliances and Arrangements, 17 November 1983	108.101 108.105
Resolution A.649(16), Code for the Construction and Equipment of Mobile Offshore Drilling Units (MODU Code), October 19, 1989 with Amendments of June, 1991	181.108 181.503
Resolution A.658(16), Use and Fitting of Retro–reflective Materials on Life–saving Appliances, 20 November, 1989	108.101 108.645 108.649
Resolution A.760(18), Symbols Related to Life–saving Appliances and Arrangements, 17 November, 1993	108.101 108.646 108.647 108.649 and 108.655
International Convention for the Safety of Life at Sea (SOLAS), Consolidated Edition, 1992	126.170
Resolution A.520(13), dated November 17, 1983—Code of Practice for the Evaluation, Testing and Acceptance of Prototype Novel Life–Saving Appliances and Arrangements	114.540 125.180 133.40
Resolution A.658(16), dated November 20, 1989—Use and Fitting of Retro–Reflective Materials on Life–Saving Appliances	122.604 131.855 131.875
Resolution A.688(17), dated November 6, 1991—Fire Test Procedures For Ignitability Bedding Components	116.405(j)
Resolution A.760(18), dated November 17, 1993—Symbols Related to Life–Savings Appliances and Arrangements	122.604(g) 131.875
International Convention for the Safety of Life at Sea, 1974 (SOLAS 74) Consolidated Edition, (Including 1992 Amendments to SOLAS 74, and 1994 Amendments to SOLAS 74), 1992	110.10-1 111.105-47(b) 112.15-1(r) 113.25-6(d)

The International Society for Measurement and Control (ISA)

67 Alexander Drive, PO Box 12277, Research Triangle Park, NC 27709

Publication	CFR Reference
Resolution A.654 (XVI) Graphical Symbols for Fire Control Plans, October 19, 1989	109.105 109.563
RP 12.6, Wiring Practices for Hazardous (Classified) Locations Instrumentation Part I: Intrinsic Safety, 1995	110.10-1 111.105-11(e)

Lloyd's Register of Shipping (LF)

100 Leadenhall Street, London, ECA 3BP

Publication	CFR Reference
Rules and Regulations for the Classification of Ships, 1998	91.15-5(b)
Lloyd's Register of Shiping Supplemental Requirements, 1998	91.15-5(b)

National Electrical Manufacturers Association

1300 North 17th Street, Suite 1847, Rosslyn, VA 22209; Telephone: (703) 841–3200; FAX: (703) 841–3300

Publication	CFR Reference
NEMA Standards Publication No. ICS 2, Industrial Control and Systems Controllers, Contactors, and Overload Relays Rated Not More Than 2000 Volts AC or 750 Volts DC, 1993	110.10-1 111.70-3(a)
NEMA Standards Publication No. 2.3 1983, Instructions for the Handling, Installation, Operation, and Maintenance of Motor Control Centers, 1983	110.10-1 111.70-3(a)
NEMA Standards Publication No. 2.4, NEMA and IEC Devices for Motor Service—A Guide for Understanding the Differences, 1989	110.10-1 111.70-3(a).
NEMA Standards Publication No. 250, Enclosures for Electrical Equipment (1000 Volts Maximum), 1991	110.10-1 111.01-9(a) 111.01-9(b) 111.01-9(c) 111.01-9(d) 111.01-9(Note) 111.10-7 113.20-3 113.25-11 113.30-25(c) 113.30-25(h) 113.40-10(b)
NEMA Standards Publication No. WC–3, Rubber–Insulated Wire and Cable for the Transmission and Distribution of Electrical Energy, 1980 (with revisions through May 1989)	110.10-1 111.60-13(a) 111.60-13(c)
NEMA Standards Publication No. WC–8, Ethylene–Propylene–Rubber–Insulated Wire and Cable for the Transmission and Distribution of Electrical Energy, 1988 (with revisions through 1992)	110.10-1 111.60-13(a) 111.60-13(c)

National Fire Protection Association

1 Batterymarch Park, Quincy, MA 02269–9101, Telephone: (800) 344–3555

Publication	CFR Reference
306—Control of Gas Hazards on Vessels, 1980	91.50-1
306—Control of Gas Hazards on Vessels, 1980	109.573
407—Standard for Aircraft Fuel Servicing, 1980	108.239
496—Standard for Purged and Pressurized Enclosures for Electrical Equipment in Hazardous Locations, 1974	108.187
NFPA 13–1996 Standard for the Installation of Sprinkler Systems	95.01-2 95.30-1 108.101 108.430
No. 56A–1973 Standard for the Use of Inhalation Anesthetics	111.105-37
NFPA 70 The National Electric Code, 1997	110.10-1 111.05-33 111.20-15 111.25-5(a) 111.30-19(d), (f)(1) 111.50-3 111.50-9 111.53-1(a) 111.54-1(a) 111.55-1(a) 111.59-1 Table 111.60-7 111.60-11(f) 111.60-13 111.81-1(d) 111.83-3(a) 111.105-1(Note) 111.105-3 111.105-5 111.105-7 111.105-9 111.105-17(b) 111.107-1(b)
NFPA 77 Recommended Practice on Static Electricity, 1993	110.10-1 111.105-27
NFPA 99 Standard for Health Care Facilities, 1997	110.10-1 111.105-37
NFPA 496 Standard for Purged and Pressurized Enclosures for Electrical Equipment, 1993	110.10-1 111.105-7(b)
NFPA 10–1994—Portable Fire Extinguishers	115.810 132.350
NFPA 13–1994—Installation of Sprinkler Systems	116.439
NFPA 13–1996—Installation of Sprinkler Systems	114.600 116.439
NFPA 17–1994—Dry Chemical Extinguishing Systems	118.425
NFPA 17A–1994—Wet Chemical Extinguishing Systems	118.425
NFPA 70–1993—National Electrical Code (NEC)	120.320 120.340 120.370 129.320 129.340 129.370
NFPA 92B–1991—Smoke Management Systems in Malls, Atria, and Large Areas	116.440
NFPA 92B–1995—Smoke Management Systems in Malls, Atria, and Large Areas	114.600 116.440
NFPA 261–1994—Test for Determining Resistance of Mock–up Upholstered Furniture Material Assemblies to Ignition by Smoldering Cigarettes	114.400 116.423
NFPA 302–1994—Pleasure and Commercial Motor Craft, Chapter 6	121.200 121.240 129.550
NFPA 306–1993—Control of Gas Hazards on Vessels	115.710 126.160
NFPA 701–1989—Fire Tests for Flame–Resistant Textiles and Films	116.423
NFPA 701–1996—Fire Tests for Flame–Resistant Textiles and Films	114.600 116.423
NFPA 1963–1993—Fire Hose Connections	118.320 132.130

Underwriters Laboratories, Inc.

Available from: Global Engineering Documents, 15 Inverness Way East, Englewood, CO 80112, Telephone (800) 854–7179 or
Global Engineering Documents, 7730 Carondelet Ave., Suite 470, Clayton, MO 63105, Telephone (800) 854–7179

Publication	CFR Reference
UL 19–78 Woven–jacketed, Rubber Lined Fire Hose	95.10-10 108.425
UL 20–79 General Use Snap Switches	111.55-7
UL 44 Standard for Rubber–Insulated Wire and Cable, 1991 (revisions through February, 1996)	110.10-1 111.60-11(c)
UL 50 Standard for Enclosures for Electrical Equipment, 1995	110.10-1 111.81-1
UL 62 Standard for Flexible Cord ad Fixture Wire, 1991 (revisions through February, 1996)	110.10-1 111.60-13(a)
UL 67–79 (revisions and MSs through Nov. 1979) Panelboards	111.40-1
UL 73–81 Motor Operated Applicances	111.77-5(a)
UL 83 Standard for Thermoplastic–Insulated Wires and Cables, 1991 (with revisions through March, 1996)	110.10-1 111.60-1(c) 111.60-11(c)
UL 98–74 (revisions and MSs through July 1980) Enclosed Switches	111.55-9
UL 104–73 Elevator Door Locking Devices and Contacts	111.91-3
UL 197–78 (revisions and MSs through Nov. 1979) Commercial Electric Cooking Applicances	111.77-3(a)
UL 250–79 (revisions through Apr. 1979) Household Refrigerators and Freezers	111.77-9
UL 347–79 High–Voltage Industrial Control Equipment	111.70-3(d)
UL 363–80 Knife Switches	111.55-5
UL 399–78 (revisions thorugh Apr. 1980) Drinking Water Coolers	111.77-11
UL 471–78 (revisions through Apr. 1980) Commercial Refrigerators and Freezers	111.77-9
UL 486A–78 Electric Wire Connectors and Soldering Lugs for Use With Copper Conducters	111.60-17(d) 111.60-19(b)(1)
UL 489 Standard for Molded Case Circuit–Breakers and Circuit–Breakers Enclosures, 1991 (revisions through June, 1995)	110.10-1 111.01-15(c) 111.54-(b) 111.54-1(b)
UL 498–79 (revisions through Jan. 1979) Electrical Attachment Plugs and Attachment Plugs and Receptacles	111.79-1(d)
UL 508–77 (revisions and MSs through Jan. 1981) Electric Industrial Control Equipment	111.70-3(d)
UL 514A Standard for Metallic Outlet Boxes, 1991 (revisions through April, 1995)	110.10-1 111.81-1
UL 514B Standard for Fittings for Conduit and Outlet Boxes, 1989 (revisions through April, 1995)	110.10-1 111.81-1
UL 514C Standard for Nonmetallic Outlet Boxes, Flush–Device Boxes, and Covers, 1988 (revisions through April, 1995)	110.10-1 111.81-1
UL 595 Standard for Marine–Type Electric Lighting Fixtures, 1985 (revisions through September, 1991)	110.10-1 111.75-20(a), (e)
UL 749–78 (revisions through Dec. 1979) Household Electric Dishwashers	111.77-7
UL 845–80 Electric Motor Control Centers	111.70-3(d)
UL 857–80 Busways and Associated Fittings	111.59-1(b)
UL 913, Standard for Intrinsically Safe Apparatus and Associated Apparatus for Use in Class I, II, and III Division 1, Hazardous (Classified) Locations, 1988	110.10-1 111.105-11(a)
UL 921–78 (revisions through Oct. 1980) Commercial Electric Dishwashers	111.77-7
UL 924–79 (revisions through Feb. 1979) Emergency Lighting Equipment	112.39-1(a)(4)
UL 1025–80 (revisions and MSs through Nov. 1980) Electric Air Heaters	111.87-3(a)
UL 1042 Standard for Electric Baseboard Heating Equipment, 1994 (revisions through November 1995)	110.10-1 111.87-3(a)
UL 1072, Standard for Medium–Voltage Power Cables, 1995 (revisions through January, 1996)	110.10-1 111.60-1(e)
UL 1096, Standard for Electric Central Air Heating Equipment, 1986 (revisions through January, 1988)	110.10-1 111.87-3(a)
UL 1104 Standard for Marine Navigation Lights, 1981 (revisions through May 1988)	110.10-1 111.75-17(d)
UL 1203, Standard for Explosion–Proof and Dust–Ignition–Proof Electrical Equipment for Use in Hazardous (Classified) Locations, 1994 (revisions through October 1995)	110.10-1 111.105-9
UL 1236–78 (revisions and MSs through Feb. 1980) Electric Battery Chargers	111.15-30
UL 1309, Standard for Marine Shipboard Cable, July 14, 1995	110.10-1 111.60-1 111.60-3
UL 1569, Standard for Metal–Clad Cables, 1995 (including revisions through April, 1996)	110.10-1 111.60-23(a)
UL 1570, Standard for Florescent Lighting Fixtures, 1988 (revisions through April, 1996)	110.10-1 111.75-20
UL 1571, Standard for Incandescent Lighting Fixtures, 1995 (revisions through April, 1996)	110.10-1 111.75-20
UL 1572, Standard for High Intensity Discharge Lighting Fixtures, 1995 (including revisions through May, 1996)	110.10-1 111.75-20
UL 1573, Standard for Stage and Studio Lighting Units, 1994 (revisions through February, 1995)	110.10-1 111.75-20
UL 1574, Standard for Track Lighting Systems, 1995 (revisions through July, 1995)	110.10-1 111.75-20
ANSI/UL 1581, Reference Standard for Electrical Wires, Cables, and Flexible Cords, 1991 (revisions through January, 1996)	110.10-1 111.30-19(b) 111.60-2 111.60-6(a)
UL 19–1992—Lined Fire Hose and Hose Assemblies	118.320 132.130
UL 57–1976 Electric Lighting Fixtures	129.410
UL 174–1989, as amended through June 23, 1994—Household Electric Storage Tank Water Heaters	119.320
UL 486A–1992—Wire Connectors and Soldering Lugs for Use With Copper Conductors	120.340 129.340
UL 489–1995—Molded—Case Circuit Breakers and Circut Breaker Enclosures	120.380 129.380
UL 595–1991—Marine Type Electric Lighting Fixtures	120.410 129.410
UL 710–1990, as amended through Sept. 16, 1993—Exhaust Hoods for Commercial Cooking Equipment	118.425
UL 723–1993, as amended through April 20, 1994—Test for Surface Burning Characteristics of Building Materials	114.400 116.422 116.423 116.425
UL 1056–1989—Fire Test of Upholstered Furniture	116.423
UL 1058–1989, as amended through April 19, 1994—Halogenated Agent Extinguishing System Units	118.410
UL 1102–1992—Non integral Marine Fuel Tanks	119.440
UL 1104–1981, as amended through May 4, 1988—Marine Navigation Lights	120.420
UL 1110–1988, as amended through May 16, 1994—Marine Combustible Gas Indicators	119.480
UL 1453–1988, as amended through June 7, 1994—Electric Booster and Commercial Storage Tank Water Heaters	119.320
UL 1570–1995—Fluorescent Lighting Fixtures	120.410 129.410
UL 1571–1995—Incandescent Lighting Fixtures	120.410 129.410
UL 1572–1995—High Intensity Discharge Lighting Fixtures	120.410 129.410
UL 1573–1995—Stage and Studio Lighting Units	120.410 129.410
UL 1574–1995—Track Lighting Systems	120.410 129.410