You are using an unsupported browser. This web site is designed for the current versions of Microsoft Edge, Google Chrome, Mozilla Firefox, or Safari.
The Office of the Federal Register publishes documents on behalf of Federal agencies but does not have any authority over their programs. We recommend you directly contact the agency associated with the content in question.
If you have comments or suggestions on how to improve the www.ecfr.gov website or have questions about using www.ecfr.gov, please choose the 'Website Feedback' button below.
If you would like to comment on the current content, please use the 'Content Feedback' button below for instructions on contacting the issuing agency
Enhanced content is provided to the user to provide additional context.
This content is from the eCFR and is authoritative but unofficial.
Navigate by entering citations or phrases (eg: 1 CFR 1.1 49 CFR 172.101 Organization and Purpose 1/1.1 Regulation Y FAR).
Choosing an item from citations and headings will bring you directly to the content. Choosing an item from full text search results will bring you to those results. Pressing enter in the search box will also bring you to search results.
Background and more details are available in the Search & Navigation guide.
The in-page Table of Contents is available only when multiple sections are being viewed.
Use the navigation links in the gray bar above to view the table of contents that this content belongs to.
49 U.S.C. 20102-20114 and 20142; 28 U.S.C. 2461 note; and 49 CFR 1.89.
63 FR 34029, June 22, 1998, unless otherwise noted.
This content is from the eCFR and may include recent changes applied to the CFR. The official, published CFR, is updated annually and available below under "Published Edition". You can learn more about the process here.
Subscribe to: 49 CFR 213.331
No changes found for this content after 1/03/2017.
View the most recent official publication:
These links go to the official, published CFR, which is updated annually. As a result, it may not include the most recent changes applied to the CFR. Learn more.
Information and documentation can be found in our developer resources.
The Code of Federal Regulations (CFR) is the official legal print publication containing the codification of the general and permanent rules published in the Federal Register by the departments and agencies of the Federal Government. The Electronic Code of Federal Regulations (eCFR) is a continuously updated online version of the CFR. It is not an official legal edition of the CFR.
Learn more about the eCFR, its status, and the editorial process.
(a) For a single deviation in track surface, each track owner shall maintain the surface of its track within the limits prescribed in the following table:
| Track surface (inches) | Class of track | |||
|---|---|---|---|---|
| 6 | 7 | 8 | 9 | |
| The deviation from uniform 1 profile on either rail at the mid-ordinate of a 31-foot chord may not be more than | 1 | 1 | 3⁄4 | 1⁄2 |
| The deviation from uniform profile on either rail at the mid-ordinate of a 62-foot chord may not be more than | 1 | 1 | 1 | 3⁄4 |
| Except as provided in paragraph (b) of this section, the deviation from uniform profile on either rail at the mid-ordinate of a 124-foot chord may not be more than | 13⁄4 | 11⁄2 | 11⁄4 | 1 |
| The deviation from zero crosslevel at any point on tangent track may not be more than 2 | 1 | 1 | 1 | 1 |
| Reverse elevation on curves may not be more than | 1⁄2 | 1⁄2 | 1⁄2 | 1⁄2 |
| The difference in crosslevel between any two points less than 62 feet apart may not be more than 3 | 11⁄2 | 11⁄2 | 11⁄4 | 1 |
| On curved track, the difference in crosslevel between any two points less than 10 feet apart (short warp) may not be more than | 11⁄4 | 11⁄8 | 1 | 3⁄4 |
| 1 Uniformity for profile is established by placing the midpoint of the specified chord at the point of maximum measurement. | ||||
| 2 If physical conditions do not permit a spiral long enough to accommodate the minimum length of runoff, part of the runoff may be on tangent track. | ||||
| 3 However, to control harmonics on jointed track with staggered joints, the crosslevel differences shall not exceed 1 inch in all of six consecutive pairs of joints, as created by seven low joints. Track with joints staggered less than 10 feet apart shall not be considered as having staggered joints. Joints within the seven low joints outside of the regular joint spacing shall not be considered as joints for purposes of this footnote. | ||||
(b) For operations at a qualified cant deficiency, Eu, of more than 5 inches, a single deviation in track surface shall be within the limits prescribed in the following table:
| Track surface (inches) | Class of track | |||
|---|---|---|---|---|
| 6 | 7 | 8 | 9 | |
| The difference in crosslevel between any two points less than 10 feet apart (short warp) may not be more than | 11⁄4 | 1 | 11 | 3⁄4 |
| The deviation from uniform profile on either rail at the mid-ordinate of a 124-foot chord may not be more than | 11⁄2 | 11⁄4 | 11⁄4 | 1 |
| 1 For curves with a qualified cant deficiency, Eu, of more than 7 inches, the difference in crosslevel between any two points less than 10 feet apart (short warp) may not be more than three-quarters of an inch. | ||||
(c) For three or more non-overlapping deviations in track surface occurring within a distance equal to five times the specified chord length, each of which exceeds the limits in the following table, each track owner shall maintain the surface of the track within the limits prescribed for each deviation:
| Track surface (inches) | Class of track | |||
|---|---|---|---|---|
| 6 | 7 | 8 | 9 | |
| The deviation from uniform profile on either rail at the mid-ordinate of a 31-foot chord may not be more than | 3⁄4 | 3⁄4 | 1⁄2 | 3⁄8 |
| The deviation from uniform profile on either rail at the mid-ordinate of a 62-foot chord may not be more than | 3⁄4 | 3⁄4 | 3⁄4 | 1⁄2 |
| The deviation from uniform profile on either rail at the mid-ordinate of a 124-foot chord may not be more than | 11⁄4 | 1 | 7⁄8 | 5⁄8 |
[78 FR 16106, Mar. 13, 2013]