Site Feedback

Website Feedback

This contact form is only for website help or website suggestions. If you have questions or comments regarding a published document please contact the publishing agency. Comments or questions about document content can not be answered by OFR staff. Please do not provide confidential information or personal data.

Title 40

This content is from the eCFR and is authoritative but unofficial.

Displaying title 40, up to date as of 6/16/2026. Title 40 was last amended 6/15/2026.
view historical versions
  1. Title 40 —Protection of Environment
  2. Chapter I —Environmental Protection Agency
  3. Subchapter N —Effluent Guidelines and Standards
  4. Part 464 —Metal Molding and Casting Point Source Category
  5. Subpart C
eCFR Content

The Code of Federal Regulations (CFR) is the official legal print publication containing the codification of the general and permanent rules published in the Federal Register by the departments and agencies of the Federal Government. The Electronic Code of Federal Regulations (eCFR) is a continuously updated online version of the CFR. It is not an official legal edition of the CFR.

Learn more about the eCFR, its status, and the editorial process.

Enhanced Content
View table of contents for this page.

Subpart C—Ferrous Casting Subcategory

§ 464.30 Applicability; description of the ferrous casting subcategory.

The provisions of this subpart are applicable to discharges to waters of the United States and to the introduction of pollutants into publicly owned treatment works resulting from ferrous casting operations as defined in § 464.02(c).

§ 464.31 Specialized definitions.

For the purpose of this subpart:

(a) Total Toxic Organics (TTO). TTO is a regulated parameter under PSES (§ 464.35) and PSNS (§ 464.36) for the ferrous subcategory and is comprised of a discrete list of toxic organic pollutants for each process segment where it is regulated, as follows:

(1) Casting Quench (§§ 464.35(b) and 464.36(b)):

23. chloroform (trichloromethane)

34. 2,4-dimethylphenol

(2) Dust Collection Scrubber (§§ 464.35(c) and 464.36(b)):

1. acenaphthene

23. chloroform (trichloromethane)

31. 2,4-dichlorophenol

34. 2,4-dimethylphenol

39. fluoranthene

44. methylene chloride (dichloromethane)

55. naphthalene

64. pentachlorophenol

65. phenol

66. bis(2-ethylhexyl)phthalate

67. butyl benzyl phthalate

68. di-n-butyl phthalate

70. diethyl phthalate

71. dimethyl phthalate

72. benzo (a)anthracene (1,2-benzanthracene)

76. chrysene

77. acenaphthylene

78. anthracene

80. fluorene

81. phenanthrene

84. pyrene

(3) Investment Casting (§§ 464.35(e) and 464.36(e)):

23. chloroform (trichloromethane)

44. methylene chloride (dichloromethane)

66. bis (2-ethylhexyl) phthalate

77. acenaphthylene

84. pyrene

(4) Melting Furnace Scrubber (§§ 464.35(f) and 464.36(f)):

23. chloroform (trichloromethane)

31. 2,4-dichlorophenol

34. 2,4-dimethylphenol

39. fluoranthene

44. methylene chloride (dichloromethane)

55. naphthalene

65. phenol

66. bis (2-ethylhexyl) phthalate

67. butyl benzyl phthalate

68. di-n-butyl phthalate

72. benzo (a)anthracene (1,2-benzanthracene)

76. chrysene

77. acenaphthylene

78. anthracene

80. fluorene

81. phenanthrene

84. pyrene

(5) Mold Cooling (§§ 464.35(g) and 464.36(g)):

23. chloroform (trichloromethane)

34. 2,4-dimethylphenol

(6) Slag Quench (§§ 464.35(h) and 464.36(h)):

34. 2,4-dimethylphenol

71. dimethyl phthalate

(7) Wet Sand Reclamation (§§ 464.35(i) and 464.36(i)):

1. acenaphthene

34. 2,4-dimethylphenol

39. fluoranthene

44. methylene chloride (dichloromethane)

55. naphthalene

65. phenol

66. bis (2-ethylhexyl) phthalate

68. di-n-butyl phthalate

70. diethyl phthalate

71. dimethyl phthalate

72. benzo(a)anthracene (1,2-benzanthracene)

77. acenaphthylene

84. pyrene

(b) Cast Iron. An iron containing carbon in excess of the solubility in the austentite that exists in the alloy at the eutectic temperature. Cast iron also is defined here to include any iron-carbon alloys containing 1.2 percent or more carbon by weight.

(c) Ductile Iron. A cast iron that has been treated while molten with a master alloy containing an element such as magnesium or cerium to induce the formation of free graphite as nodules or spherules, which imparts a measurable degree of ductility to the cast metal.

(d) Gray Iron. A cast iron that gives a gray fracture due to the presence of flake graphite.

(e) Malleable Iron. A cast iron made by a prolonged anneal of white cast iron in which decarburization or graphitization, or both, take place to eliminate some or all of the cementite. Graphite is present in the form of temper carbon.

(f) Steel. An iron-base alloy containing carbon, manganese, and often other alloying elements. Steel is defined here to include only those iron-carbon alloys containing less than 1.2 percent carbon by weight.

(g) The “primary metal cast” shall mean the metal that is poured in the greatest quantity at an individual plant.

(h) Multiple Ferrous Melting Furnace Scrubber Configuration. A multiple ferrous melting furnace scrubber configuration is a configuration where two or more discrete wet scrubbing devices are employed in series in a single melting furnace exhaust gas stream. The ferrous melting furnace scrubber mass allowance shall be given to each discrete wet scrubbing device that has an associated wastewater discharge in a multiple ferrous melting furnace scrubber configuration. The mass allowance for each discrete wet scrubber shall be identical and based on the air flow of the exhaust gas stream that passes through the multiple scrubber configuration.

(i) Discrete Wet Scrubbing Device. A discrete wet scrubbing device is a distinct, stand-alone device that removes particulates and fumes from a contaminated gas stream by bringing the gas stream into contact with a scrubber liquor, usually water, and from which there is a wastewater discharge. Examples of discrete wet scrubbing devices are: Spray towers and chambers, venturi scrubbers (fixed and variable), wet caps, packed bed scrubbers, quenchers, and orifice scrubbers. Semi-wet scrubbing devices where water is added and totally evaporates prior to dry air pollution control are not considered to be discrete wet scrubbing devices. Ancillary scrubber operations such as fan washes and backwashes are not considered to be discrete wet scrubber devices. These ancillary operations are covered by the mass limitations of the associated scrubber. Aftercoolers are not considered to be discrete wet scrubbing devices, and water discharges from aftercooling are not regulated as a process wastewater in this category.

§ 464.32 Effluent limitations guidelines representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available.

Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available, except that non-continuous dischargers shall not be subject to the maximum day and maximum for monthly average mass (kg/1,000 kkg or lb/million lb of metal poured; kg/1,000 kkg or lb/million lb of sand reclaimed; kg/62.3 million Sm3 or lb/billion SCF of air scrubbed) effluent limitations for copper, lead, zinc, total phenols, oil and grease, and TSS. For non-continuous dischargers, annual average mass limitations and maximum day and maximum for monthly average concentration (mg/l) limitations shall apply. Concentration limitations and annual average mass limitations shall only apply to non-continuous dischargers.

(a) Casting Cleaning Operations.

BPT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0129 0.0071
Lead (T) 0.0353 0.0174
Zinc (T) 0.0656 0.025
Oil and grease 1.34 0.446
TSS 1.7 0.67
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0029
Lead (T) 0.79 0.39 0.0098
Zinc (T) 1.47 0.56 0.0179
Oil and grease 30 10 0.223
TSS 38 15 0.446
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio (5.33/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(b) Casting Quench Operations.

BPT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0138 0.0076
Lead (T) 0.0376 0.0185
Zinc (T) 0.0699 0.0266
Oil and grease 1.43 0.476
TSS 1.81 0.713
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0031
Lead (T) 0.79 0.39 0.0105
Zinc (T) 1.47 0.56 0.019
Oil and grease 30 10 0.238
TSS 38 15 0.476
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (5.7/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(c) Dust Collection Scrubber Operations.

BPT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 0.218 0.12
Lead (T) 0.593 0.293
Zinc (T) 1.1 0.421
Total phenols 0.656 0.225
Oil and grease 22.5 7.51
TSS 28.5 11.3
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0488
Lead (T) 0.79 0.39 0.165
Zinc (T) 1.47 0.56 0.3
Total phenols 0.86 0.3 0.15
Oil and grease 30 10 3.76
TSS 38 15 7.51
pH (3) (3) (3)
1 kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed.
2 These concentrations must be multiplied by the ratio (0.090/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 SCF of air scrubbed) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(d) Grinding Scrubber Operations. No discharge of process wastewater pollutants to navigable waters.

(e) Investment Casting.

BPT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 3.19 1.76
Lead (T) 8.7 4.3
Zinc (T) 16.2 6.17
Oil and grease 330 110
TSS 419 165
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.716
Lead (T) 0.79 0.39 2.42
Zinc (T) 1.47 0.56 4.41
Oil and grease 30 10 55.1
TSS 38 15 110
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (1,320/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(f) Melting Furnace Scrubber Operations.

BPT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 1.02 0.561
Lead (T) 2.77 1.37
Zinc (T) 5.15 1.96
Total phenols 3.01 1.05
Oil and grease 105 35
TSS 133 52.6
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.228
Lead (T) 0.79 0.39 0.771
Zinc (T) 1.47 0.56 1.4
Total phenols 0.86 0.3 0.701
Oil and grease 30 10 17.5
TSS 38 15 35
pH (3) (3) (3)
1 kg/62.3 million Sm3 (pounds per billion SCF) or air scrubbed.
2 These concentrations must be multiplied by the ratio of (0.42/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 SCF of air scrubbed) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(g) Mold Cooling Operations.

BPT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0428 0.0236
Lead (T) 0.117 0.0576
Zinc (T) 0.217 0.0827
Oil and grease 4.43 1.48
TSS 5.61 2.22
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0096
Lead (T) 0.79 0.39 0.0325
Zinc (T) 1.47 0.56 0.0591
Oil and grease 30 10 0.738
TSS 38 15 1.48
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of metal poured
2 These concentrations must be multiplied by the ratio of (17.7/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(h) Slag Quench Operations.

BPT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0527 0.0291
Lead (T) 0.144 0.0709
Zinc (T) 0.267 0.102
Oil and grease 5.46 1.82
TSS 6.91 2.73
pH (1) (1)
1 Within the range 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0118
Lead (T) 0.79 0.39 0.04
Zinc (T) 1.47 0.56 0.0728
Oil and grease 30 10 0.909
TSS 38 15 1.82
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (21.8/x) where x is the actual normalized process wasterwater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(i) Wet Sand Reclamation Operations.

BPT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of sand reclaimed
Copper (T) 0.217 0.12
Lead (T) 0.59 0.291
Zinc (T) 1.1 0.418
Total phenols 0.642 0.224
Oil and grease 22.4 7.47
TSS 28.4 11.2
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0485
Lead (T) 0.79 0.39 0.164
Zinc (T) 1.47 0.56 0.299
Total phenols 0.86 0.3 0.149
Oil and grease 30 10 3.73
TSS 38 15 7.47
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of sand reclaimed.
2 These concentrations must be multiplied by the ratio of (89.5/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of sand reclaimed) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

[50 FR 45247, Oct. 30, 1985; 51 FR 21761, June 16, 1986]

§ 464.33 Effluent limitations guidelines representing the degree of effluent reduction attainable by the application of the best available technology economically achievable.

Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable, except that non-continuous dischargers shall not be subject to the maximum day and maximum for monthly average mass (kg/1,000 kkg or lb/million lb of metal poured; kg/1,000 kkg or lb/million lb of sand reclaimed; kg/62.3 million Sm3 or lb/billion SCF of air scrubbed) effluent limitations for copper, lead, zinc, and total phenols. For non-continuous dischargers, annual average mass limitations and maximum day and maximum for monthly average concentration (mg/l) limitations shall apply. Concentration limitations and annual average mass limitations shall only apply to non-continuous dischargers.

(a) Casting Cleaning Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0129 0.0071
Lead (T) 0.0237 0.0116
Zinc (T) 0.0437 0.0165
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0029
Lead (T) 0.53 0.26 0.0067
Zinc (T) 0.98 0.37 0.0116
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (5.33/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0129 0.0071
Lead (T) 0.0353 0.0174
Zinc (T) 0.0656 0.025
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0029
Lead (T) 0.79 0.39 0.0098
Zinc (T) 1.47 0.56 0.0179
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (5.33/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(b) Casting Quench Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/100 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0138 0.0076
Lead (T) 0.0252 0.0124
Zinc (T) 0.0466 0.0176
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l)2 (mg/l)2
Copper (T) 0.29 0.16 0.0031
Lead (T) 0.53 0.26 0.0071
Zinc (T) 0.98 0.37 0.0124
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (5.7/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0138 0.0076
Lead (T) 0.0376 0.0185
Zinc (T) 0.0699 0.0266
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l)2 (mg/l)2
Copper (T) 0.29 0.16 0.0031
Lead (T) 0.79 0.39 0.0105
Zinc (T) 1.47 0.56 0.019
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (5.7/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(c) Dust Collection Scrubber Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 0.218 0.12
Lead (T) 0.398 0.195
Zinc (T) 0.736 0.278
Total phenols 0.646 0.225
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l)2 (mg/l)2
Copper (T) 0.29 0.16 0.0488
Lead (T) 0.53 0.26 0.113
Zinc (T) 0.98 0.37 0.195
Total phenols 0.86 0.3 0.15
1 kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed.
2 These concentrations must be multiplied by the ratio of (0.09/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 SCF of air scrubbed) for a specific plant.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 0.218 0.12
Lead (T) 0.593 0.293
Zinc (T) 1.1 0.421
Total phenols 0.656 0.225
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l)2 (mg/l)2
Copper (T) 0.29 0.16 0.0488
Lead (T) 0.79 0.39 0.165
Zinc (T) 1.47 0.56 0.3
Total phenols 0.86 0.3 0.15
1 kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed.
2 These concentrations must be multiplied by the ratio of (0.09/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 SCF of air scrubbed) for a specific plant.

(d) Grinding Scrubber Operations. No discharge of process wastewater pollutants to navigable waters.

(e) Investment Casting.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 3.19 1.76
Lead (T) 5.84 2.86
Zinc (T) 10.8 4.07
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.716
Lead (T) 0.53 0.26 1.65
Zinc (T) 0.98 0.37 2.86
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (1,320/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 3.19 1.76
Lead (T) 8.7 4.3
Zinc (T) 16.2 6.17
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.716
Lead (T) 0.79 0.39 2.42
Zinc (T) 1.47 0.56 4.41
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (1,320/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(f) Melting Furnace Scrubber Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 1.02 0.561
Lead (T) 1.86 0.911
Zinc (T) 3.44 1.3
Total Phenols 3.01 1.05
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.228
Lead (T) 0.53 0.26 0.526
Zinc (T) 0.98 0.37 0.911
Total Phenols 0.86 0.3 0.701
1 kg/62.3 million Sm 3 (pounds per billion SCF) of air scrubbed
2 These concentrations must be multiplied by the ratio of (0.42/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 SCF of air scrubbed) for a specific plant.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 1.02 0.561
Lead (T) 2.77 1.37
Zinc (T) 5.15 1.96
Total Phenols 3.01 1.05
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.228
Lead (T) 0.79 0.39 0.771
Zinc (T) 1.47 0.56 1.4
Total Phenols 0.86 0.3 0.701
1 kg/62.3 million Sm 3 (pounds per billion SCF) of air scrubbed.
2 These concentrations must be multiplied by the ratio of (0.42/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 SCF of air scrubbed) for a specific plant.

(g) Mold Cooling Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0428 0.0236
Lead (T) 0.0783 0.0384
Zinc (T) 0.145 0.0546
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0096
Lead (T) 0.53 0.26 0.0222
Zinc (T) 0.98 0.37 0.0384
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (17.7/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0428 0.0236
Lead (T) 0.117 0.0576
Zinc (T) 0.217 0.0827
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0096
Lead (T) 0.79 0.39 0.0325
Zinc (T) 1.47 0.56 0.0591
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (17.7/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(h) Slag Quench Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0527 0.0291
Lead (T) 0.0964 0.0473
Zinc (T) 0.178 0.0673
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0118
Lead (T) 0.53 0.26 0.0273
Zinc (T) 0.98 0.37 0.0473
1 Kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (21.8/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0527 0.0291
Lead (T) 0.144 0.0709
Zinc (T) 0.267 0.102
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0118
Lead (T) 0.79 0.39 0.04
Zinc (T) 1.47 0.56 0.0728
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (21.8/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(i) Wet Sand Reclamation Operations.

(1) Applicable to plants that are casting primarily ductible or gray iron and to plants that are casting malleable iron where greater than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of sand reclaimed
Copper (T) 0.217 0.12
Lead (T) 0.396 0.194
Zinc (T) 0.732 0.276
Total Phenols 0.642 0.224
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0485
Lead (T) 0.53 0.26 0.112
Zinc (T) 0.98 0.37 0.194
Total Phenols 0.86 0.3 0.149
1 kg/1000 kkg (pounds per million pounds) of sand reclaimed.
2 These concentrations must be multiplied by the ratio of (89.5/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of sand reclaimed) for a specific plant.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

BAT Effluent Limitations
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of sand reclaimed
Copper (T) 0.217 0.12
Lead (T) 0.59 0.291
Zinc (T) 1.1 0.418
Total Phenols 0.642 0.224

PSNS
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0485
Lead (T) 0.79 0.39 0.164
Zinc (T) 1.47 0.56 0.299
Total Phenols 0.86 0.3 0.149
1 kg/1000 kkg (pounds per million pounds) of sand reclaimed.
2 These concentrations must be multiplied by the ratio of (89.5/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of sand reclaimed) for a specific plant.

[50 FR 45247, Oct. 30, 1985; 51 FR 21761, June 16, 1986]

§ 464.34 New source performance standards.

Any new source subject to this subpart must achieve the following new source performance standards (NSPS), except that non-continuous dischargers shall not be subject to the maximum day and maximum for monthly average mass (kg/1,000 kkg or lb/million lb of metal poured; kg/1,000 kkg or lb/million lb of sand reclaimed; kg/62.3 million Sm3 or lb/billion SCF of air scrubbed) effluent standards for copper, lead, zinc, total phenols, oil and grease, and TSS. For non-continuous dischargers, annual average mass standards and maximum day and maximum for monthly average concentration (mg/l) standards shall apply. Concentration standards and annual average mass standards shall only apply to non-continuous dischargers.

(a) Casting Cleaning Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0129 0.0071
Lead (T) 0.0237 0.0116
Zinc (T) 0.0437 0.0165
Oil and grease 1.34 0.446
TSS 0.67 0.536
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0029
Lead (T) 0.53 0.26 0.0067
Zinc (T) 0.98 0.37 0.0116
Oil and grease 30 10 0.223
TTS 15 12 0.116
pH (3) (3) (3)
1 kg/1000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (5.33/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0129 0.0071
Lead (T) 0.0353 0.0174
Zinc (T) 0.0656 0.025
Oil and grease 1.34 0.446
TSS 1.7 0.67
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0029
Lead (T) 0.79 0.39 0.0098
Zinc (T) 1.47 0.56 0.0179
Oil and grease 30 10 0.223
TTS 38 15 0.446
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (5.35/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(b) Casting Quench Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0138 0.0076
Lead (T) 0.0252 0.0124
Zinc (T) 0.0466 0.0176
Oil and grease 1.43 0.476
TSS 0.713 0.571
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0031
Lead (T) 0.53 0.26 0.0071
Zinc (T) 0.98 0.37 0.0124
Oil and grease 30 10 0.238
TSS 15 12 0.124
pH (3) (3) (3)
1 Kg/1000 kkg (pounds per million pounds) of metal poured.
2 Within the range of 7.0 to 10.0 at all times.
3 These concentrations must be multiplied by the ratio of (5.7/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0138 0.0076
Lead (T) 0.0376 0.0185
Zinc (T) 0.0699 0.0266
Oil and grease 1.43 0.476
TSS 1.81 0.713
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0031
Lead (T) 0.79 0.39 0.0105
Zinc (T) 1.47 0.56 0.019
Oil and grease 30 10 0.238
TSS 38 15 0.476
pH (3) (3) (3)
1 Kg/1000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (5.7/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(c) Dust Collection Scrubber Operations.

(1) Applicable to plants that are casting primarily ductible or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 0.218 0.12
Lead (T) 0.398 0.195
Zinc (T) 0.736 0.278
Total Phenols 0.646 0.225
Oil and grease 22.5 7.51
TSS 11.3 9.01
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0488
Lead (T) 0.53 0.26 0.113
Zinc (T) 0.98 0.37 0.195
Total phenols 0.86 0.3 0.15
Oil and grease 30 10 3.76
TSS 15 12 1.95
pH (3) (3) (3)
1 kg/62.3 millions Sm3 (pound per billion SCF) of air scrubbed.
2 Within the range of 7.0 to 10.0 at all times.
3 These concentrations must be multiplied by the ratio of (0.09/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 SCF of air scrubbed) for a specific plant.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 0.218 0.12
Lead (T) 0.593 0.293
Zinc (T) 1.1 0.421
Total phenols 0.656 0.225
Oil and grease 22.5 7.51
TSS 28.5 11.3
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0488
Lead (T) 0.79 0.39 0.165
Zinc (T) 1.47 0.56 0.3
Total phenols 0.86 0.3 0.15
Oil and grease 30 10 3.76
TSS 38 15 7.51
pH (3) (3) (3)
1 kg/62.3 millions Sm3 (pound per billion SCF) of air scrubbed.
2 Within the range of 7.0 to 10.0 at all times.
3 These concentrations must be multiplied by the ratio of (0.09/) where is the actual normalized process wastewater flow (in gallons per 1,000 SCF of air scrubbed) for a specific plant.

(d) Grinding Scrubber Operations. No discharge of process wastewater pollutants to navigable waters.

(e) Investment Casting.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 3.19 1.76
Lead (T) 5.84 2.86
Zinc (T) 10.8 4.07
Oil and grease 330 110
TSS 165 132
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.716
Lead (T) 0.53 0.26 1.65
Zinc (T) 0.98 0.37 2.86
Oil and grease 30 10 55.1
TSS 15 12 28.6
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (1,320/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 3.19 1.76
Lead (T) 8.7 4.3
Zinc (T) 16.2 6.17
Oil and grease 330 110
TSS 419 165
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.716
Lead (T) 0.79 0.39 2.42
Zinc (T) 1.47 0.56 4.41
Oil and grease 30 10 55.1
TSS 38 15 110
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (1,320/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(f) Melting Furnace Scrubber Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm 3 (pounds per billion SCF) of air scrubbed
Copper (T) 1.02 0.561
Lead (T) 1.86 0.911
Zinc (T) 3.44 1.30
Total phenols 3.01 1.05
Oil and grease 105 35
TSS 52.6 42.1
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.228
Lead (T) 0.53 0.26 0.526
Zinc (T) 0.98 0.37 0.911
Total phenols 0.86 0.3 0.701
Oil and grease 30 10 17.5
TSS 15 12 9.11
pH (3) (3) (3)
1 kg/62.3 million Sm 3 (pounds per billion SCF) of air scrubbed.
2 These concentrations must be multiplied by the ratio of (0.42/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 SCF of air scrubbed) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm 3 (pounds per billion SCF) of air scrubbed
Copper (T) 1.02 0.561
Lead (T) 2.77 1.37
Zinc (T) 5.15 1.96
Total phenols 3.01 1.05
Oil and grease 105 35
TSS 133 52.6
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.228
Lead (T) 0.79 0.39 0.771
Zinc (T) 1.47 0.56 1.4
Total phenols 0.38 0.3 0.701
Oil and grease 30 10 17.5
TSS 38 15 35
pH (3) (3) (3)
1 kg/62.3 million Sm 3 (pounds per billion SCF) of air scrubbed.
2 These concentrations must be multiplied by the ratio of (0.42/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 SCF of air scrubbed) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(g) Mold Cooling Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0428 0.0236
Lead (T) 0.0783 0.0384
Zinc (T) 0.0145 0.0546
Oil and grease 4.43 1.48
TSS 2.22 1.77
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 1
Copper (T) 0.29 0.16 0.0096
Lead (T) 0.53 0.26 0.0222
Zinc (T) 0.98 0.37 0.0384
Oil and grease 30 10 0.738
TSS 15 12 0.384
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million) pounds of metal poured.
2 These concentrations must be multiplied by the ratio of (17.7/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0428 0.0236
Lead (T) 0.117 0.0576
Zinc (T) 0.217 0.0827
Oil and grease 4.43 1.48
TSS 5.61 2.22
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maxium for monthly average Annual average 1
(mg/1) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0096
Lead (T) 0.79 0.39 0.0325
Zinc (T) 1.47 0.56 0.0591
Oil and grease 30 10 0.738
TSS 38 15 1.48
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million) pounds of metal poured.
2 These concentrations must be multiplied by the ratio of (17.7/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(h) Slag Quench Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0527 0.0291
Lead (T) 0.0964 0.0473
Zinc (T) 0.178 0.0673
Oil and grease 5.46 1.82
TSS 2.73 2.18
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l) 2 (mg/l) 2
Copper (T) 0.29 0.16 0.0118
Lead (T) 0.53 0.26 0.0273
Zinc (T) 0.98 0.37 0.0473
Oil and grease 30 10 0.909
TSS 15 12 0.473
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (21.8/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0527 0.0291
Lead (T) 0.144 0.0709
Zinc (T) 0.267 0.102
Oil and grease 5.46 1.82
TSS 6.91 2.73
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average
(mg/l) 2 (mg/1) 2
Copper (T) 0.29 0.16 0.0118
Lead (T) 0.79 0.39 0.04
Zinc (T) 1.47 0.56 0.0728
Oil and grease 30 10 0.909
TSS 38 15 1.82
pH (3) (3) (3)
1 kg/1000 kkg (pounds per million pounds) of metal poured.
2 These concentrations must be multiplied by the ratio of (21.8/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of metal poured) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(i) Wet Sand Reclamation Operations.

(1) Applicable to plants that are casting primarily ductile or gray iron and to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of sand reclaimed
Copper (T) 0.217 0.12
Lead (T) 0.396 0.194
Zinc (T) 0.732 0.276
Total phenols 0.642 0.224
Oil and grease 22.4 7.47
TSS 11.2 8.96
pH (1) (1)
1 Within the range of 7.0 to 10.0 at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l)2 (mg/l)2
Copper (T) 0.29 0.16 0.0485
Lead (T) 0.53 0.26 0.112
Zinc (T) 0.98 0.37 0.194
Total phenols 0.86 0.3 0.149
Oil and grease 30 10 3.73
TSS 15 12 1.94
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of sand reclaimed.
2 These concentrations must be multiplied by the ratio of (89.5/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of sand reclaimed) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

(2) Applicable to plants that are casting primarily steel and to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year.

NSPS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of sand reclaimed
Copper (T) 0.217 0.12
Lead (T) 0.59 0.291
Zinc (T) 1.1 0.418
Total phenols 0.642 0.224
Oil and grease 22.4 7.47
TSS 28.4 11.2
pH (1) (1)
1 Within the range of 7.0 to at all times.
Maximum for any 1 day Maximum for monthly average Annual average 1
(mg/l)2 (mg/l)2
Copper (T) 0.29 0.16 0.0485
Lead (T) 0.79 0.39 0.164
Zinc (T) 1.47 0.56 0.299
Total phenols 0.86 0.3 0.149
Oil and grease 30 10 3.73
TSS 38 15 7.47
pH (3) (3) (3)
1 kg/1,000 kkg (pounds per million pounds) of sand reclaimed.
2 These concentrations must be multiplied by the ratio of (89.5/x) where x is the actual normalized process wastewater flow (in gallons per 1,000 pounds of sand reclaimed) for a specific plant.
3 Within the range of 7.0 to 10.0 at all times.

[50 FR 45247, Oct. 30, 1985; 51 FR 21761, June 16, 1986]

§ 464.35 Pretreatment standards for existing sources.

Except as provided in 40 CFR 403.7 and 403.13, any existing source subject to this subpart which introduces pollutants into a publicly owned treatment works must comply with 40 CFR part 403 and achieve the following pretreatment standards for existing sources.

(a) Casting Cleaning Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0129 0.0071
Lead (T) 0.0237 0.0116
Zinc (T) 0.0437 0.0165

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0129 0.0071
Lead (T) 0.0353 0.0174
Zinc (T) 0.0656 0.025

(b) Casting Quench Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0138 0.0076
Lead (T) 0.0252 0.0124
Zinc (T) 0.0466 0.0176
TTO 0.0257 0.00838
Oil and grease (for alternate monitoring) 1.43 0.476

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0138 0.0076
Lead (T) 0.0376 0.0185
Zinc (T) 0.0699 0.0266
TTO 0.0257 0.00838
Oil and grease (for alternate monitoring) 1.43 0.476

(c) Dust Collection Scrubber Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm 3 (pounds per billion SCF) of air scrubbed
Copper (T) 0.218 0.12
Lead (T) 0.398 0.195
Zinc (T) 0.736 0.278
Total Phenols 0.646 0.225
TTO 2.04 0.664
Oil and Grease (for alternate monitoring) 22.5 7.51

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm 3 (pounds per billion SCF) of air scrubbed
Copper (T) 0.218 0.12
Lead (T) 0.593 0.293
Zinc (T) 1.1 0.421
Total Phenols 0.656 0.225
TTO 2.04 0.664
Oil and Grease (for alternate monitoring) 22.5 7.51

(d) Grinding Scrubber Operations. No discharge of process wastewater pollutants to a POTW.

(e) Investment Casting.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 3.19 1.76
Lead (T) 5.84 2.86
Zinc (T) 10.8 4.07
TTO 13.2 4.3
Oil and Grease (for alternate monitoring) 330 110

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 3.19 1.76
Lead (T) 8.7 4.3
Zinc (T) 16.2 6.17
TTO 13.2 4.3
Oil and Grease (for alternate monitoring) 330 110

(f) Melting Furnace Scrubber Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 1.02 0.561
Lead (T) 1.86 0.911
Zinc (T) 3.44 1.30
Total phenols 3.01 1.05
TTO 8.34 2.73
Oil and grease (for alternate monitoring) 105 35

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm 3 (pounds per billion SCF) of air scrubbed
Copper (T) 1.02 0.561
Lead (T) 2.77 1.37
Zinc (T) 5.15 1.96
Total phenols 3.01 1.05
TTO 8.34 2.73
Oil and grease (for alternate monitoring) 105 35

(g) Mold Cooling Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0428 0.0236
Lead (T) 0.0783 0.0384
Zinc (T) 0.145 0.0546
TTO 0.0797 0.026
Oil and grease (for alternate monitoring) 4.43 1.48

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0428 0.0236
Lead (T) 0.117 0.0576
Zinc (T) 0.217 0.0827
TTO 0.0797 0.026
Oil and grease (for alternate monitoring) 4.43 1.48

(h) Slag Quench Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0527 0.0291
Lead (T) 0.0964 0.0473
Zinc (T) 0.178 0.0673
TTO 0.0257 0.00838
Oil and grease (for alternate monitoring) 5.46 1.82

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0527 0.0291
Lead (T) 0.144 0.0709
Zinc (T) 0.267 0.102
TTO 0.0257 0.00838
Oil and grease (for alternate monitoring) 5.46 1.82

(i) West Sand Reclamation Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting gray iron where greater than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of sand reclaimed
Copper (T) 0.217 0.12
Lead (T) 0.396 0.194
Zinc (T) 0.732 0.276
Total Phenols 0.642 0.224
TTO 1.18 0.386
Oil and grease (for alternate monitoring) 22.4 7.47

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSES
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of sand reclaimed
Copper (T) 0.217 0.12
Lead (T) 0.59 0.291
Zinc (T) 1.1 0.418
Total Phenols 0.642 0.224
TTO 1.18 0.386
Oil and grease (for alternate monitoring) 22.4 7.47

[50 FR 45247, Oct. 30, 1985; 51 FR 21762, June 16, 1986]

§ 464.36 Pretreatment standards for new sources.

Except as provided in 40 CFR 403.7, any new source subject to this subpart which introduces pollutants into publicly owned treatment works must comply with 40 CFR part 403 and achieve the following pretreatment standards for new sources.

(a) Casting Cleaning Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0129 0.0071
Lead (T) 0.0237 0.0116
Zinc (T) 0.0437 0.0165

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0129 0.0071
Lead (T) 0.0353 0.0174
Zinc (T) 0.0656 0.025

(b) Casting Quench Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0138 0.0076
Lead (T) 0.0252 0.0124
Zinc (T) 0.0466 0.0176
TTO 0.0257 0.00838
Oil and Grease (for alternate monitoring) 1.43 0.476

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0138 0.0076
Lead (T) 0.0376 0.0185
Zinc (T) 0.0699 0.0266
TTO 0.0257 0.00838
Oil and Grease (for alternate monitoring) 1.43 0.476

(c) Dust Collection Scrubber Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 0.218 0.12
Lead (T) 0.398 0.195
Zinc (T) 0.736 0.278
Total Phenols 0.646 0.225
TTO 2.04 0.664
Oil and Grease (for alternate monitoring) 22.5 7.51

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 0.218 0.12
Lead (T) 0.593 0.293
Zinc (T) 1.1 0.421
Total Phenols 0.656 0.225
TTO 2.04 0.664
Oil and Grease (for alternate monitoring) 22.5 7.51

(d) Grinding Scrubber Operations. No discharge of process wastewater pollutants to a POTW.

(e) Investment Casting.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 3.19 1.76
Lead (T) 5.84 2.86
Zinc (T) 10.8 4.07
TTO 13.2 4.3
Oil and Grease (for alternate monitoring) 330 110

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 3.19 1.76
Lead (T) 8.7 4.3
Zinc (T) 16.2 6.17
TTO 13.2 4.3
Oil and Grease (for alternate monitoring) 330 110

(f) Melting Furnace Scrubber Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 1.02 0.561
Lead (T) 1.86 0.911
Zinc (T) 3.44 1.3
Total Phenols 3.01 1.05
TTO 8.34 2.73
Oil and Grease (for alternate monitoring) 105 35

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/62.3 million Sm3 (pounds per billion SCF) of air scrubbed
Copper (T) 1.02 0.561
Lead (T) 2.77 1.37
Zinc (T) 5.15 1.96
Total Phenols 3.01 1.05
TTO 8.34 2.73
Oil and Grease (for alternate monitoring) 105 35

(g) Mold Cooling Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0428 0.0236
Lead (T) 0.0783 0.0384
Zinc (T) 0.145 0.0546
TTO 0.0797 0.026
Oil and Grease (for alternate monitoring) 4.43 1.48

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0428 0.0236
Lead (T) 0.117 0.0576
Zinc (T) 0.217 0.0827
TTO 0.0797 0.026
Oil and Grease (for alternate monitoring) 4.43 1.48

(h) Slag Quench Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0527 0.0291
Lead (T) 0.0964 0.0473
Zinc (T) 0.178 0.0673
TTO 0.0257 0.00838
Oil and grease (for alternate monitoring) 5.46 1.82

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of metal poured
Copper (T) 0.0527 0.0291
Lead (T) 0.144 0.0709
Zinc (T) 0.267 0.102
TTO 0.0257 0.00838
Oil and grease (for alternate monitoring) 5.46 1.82

(i) Wet Sand Reclamation Operations.

(1) Applicable to plants that are casting primarily ductile iron, to plants that are casting primarily malleable iron where greater than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of sand reclaimed
Copper (T) 0.217 0.12
Lead (T) 0.396 0.194
Zinc (T) 0.732 0.276
Total phenols 0.642 0.224
TTO 1.18 0.386
Oil and grease (for alternate monitoring) 22.4 7.47

(2) Applicable to plants that are casting primarily steel, to plants that are casting primarily malleable iron where equal to or less than 3,557 tons of metal are poured per year, and to plants that are casting primarily gray iron where equal to or less than 1,784 tons of metal are poured per year.

PSNS
Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average
kg/1,000 kkg (pounds per million pounds) of sand reclaimed
Copper (T) 0.217 0.12
Lead (T) 0.59 0.291
Zinc (T) 1.10 0.418
Total phenols 0.642 0.224
TTO 1.18 0.386
Oil and grease (for alternate monitoring) 22.4 7.47

§ 464.37 Effluent limitations guidelines representing the degree of effluent reduction attainable by the application of the best conventional pollutant control technology. [Reserved]

eCFR Content