49 CFR (PARTS 400–571)
NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION
All materials are available from the Office of Rulemaking, DOT–NHTSA, 400 7th St. SW., Washington, DC 20590 | 49 CFR
|
American Association of Textile Chemists and Colorists
Post Office Box 886, Durham, NC
|
| AATCC Chart for Measuring Transference of Color | 571.209
|
| Standard Test Method 8–1961 Colorfast to Crocking | 571.209
|
| Standard Test Method 30–1957T Fungicides, Evaluation of Textiles; Mildew and Rot Resistence of Textiles: Section 1C1, Water Leaching; Section 1C2, Volatilization; Section 1B3, Soil Burial Test | 571.209
|
| Standard Test Method 107–1981 Colorfastness to Water | 571.209
|
| Geometric Gray Scale | 571.209
|
American National Standards Institute (ANSI)
25 West 43rd Street, 4th Floor, New York, NY 10036; phone: 1 (212) 642–4900; fax: 1 (212) 398–0023; http://webstore.ansi.org/ansidocstore/default.asp
Copies of certain standards may be obtained from RESNA, 1700 North Moore Street, Suite 1540, Arlington, VA22209–1903
|
| ANSI/SAE Z26.1, American National Standard for Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways—Safety Standard, 1996 | 571.5; 571.205
|
| ANSI/RESNA Standard WC/Vol. 1–1998, Section 13, “Wheelchairs: Determination of Coefficient of Friction of Test Surfaces“ | 571.5, 571.403
|
American Society of Mechanical Engineers (ASME)
Three Park Avenue, New York, NY 10016–5990; phone: 1–800–843–2763 or 1–973–882–1170; fax: 1–973–882–1717; http://www.asme.org/
|
| ASME Boiler and Pressure Vessel Code, Section IX, Article II, QW–304 and QW–305 (1992) | 571.5; 571.304
|
| ASME Boiler and Pressure Vessel Code, Section VIII, UW–12 (1989) | 571.5; 571.304
|
| ASME Boiler and Pressure Vessel Code, Section VIII, U–1 through U–3, and UW–51 through UW–53 (1989) | 571.5; 571.304
|
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA, 19428–2959, Telephone (610) 832–9585, FAX (610) 832–9555
|
| ASTM 1003–61 Haze and Luminous Transmittance of Transparent Plastic | 571.108
|
| ASTM A 166–61T Tentative Specifications for Electrodeposited Coatings of Nickel and Chromium on Steel | 571.208; 571.209
|
| ASTM A 505–87, Standard Specification for Steel, Sheet and Strip, Alloy, Hot–Rolled and Cold–Rolled, General Requirements for | 571.5; 571.304
|
| ASTM A 255–89, Standard Method for End–Quench Test for Hardenability of Steel | 571.5; 571.304
|
| ASTM B 117–64, Standard Method of Salt Spray (fog) Testing | 571.106
|
| ASTM B 117–73, Standard Method of Salt Spray (fog) Testing | 571.108; 571.125; 571.209
|
| ASTM B 117–97 Standard Practice for Operating Salt Spray (fog) Apparatus | 571.5; 571.403
|
| ASTM B 117–03 Standard Practice for Operating Salt Spray (fog) Apparatus | 571.106, S6.11
|
| ASTM B 456–79 Standard Specification for Electrodeposited Coatings of Copper Plus Nickel Plus Chromium and Nickel Plus Chronium | 571.209
|
| ASTM B 456–95 Standard Specification for Electrodeposited Coatings of Copper Plus Nickel Plus Chromium and Nickel Plus Chronium | 571.5; 571.403
|
| ASTM C 150–77 Standard Specification for Portland Cement | 571.108
|
| ASTM D 362–84 Standard Specification for Industrial Grade Toluene | 571.108; 571.205
|
| ASTM D 445–65 Standard Method of Test for Viscosity of Transparent and Opaque Liquids (Kinematic and Dynamic Viscosity), Appendix 1 | 571.116
|
| ASTM D 471–98 Standard Test Method for Rubber Property–––Effect of Liquids | 571.106, S10.7
|
| ASTM D 484–71 Standard Specifications for Hydrocarbon Dry Cleaning Solvent | 571.301
|
| ASTM D 523–62T Tentative Method of Test for Specular Glass | 571.107
|
| ASTM D 756–78 Standard Practice for Determination of Weight and Shape Changes of Plastics Under Accelerated Service Conditions | 571.209
|
| ASTM D 1056–73 Standard Specifications for Flexible Cellular Materials Sponge or Expanded Rubber | 571.213
|
| ASTM D 1121–67 Standard Method of Test for Reserve Alaklinity of Engine Antifreezes and Antirusts, Appendix A1.1, A1.2, and A1.3 | 571.116
|
| ASTM D 1123–59 Standard Method of Test for Water in Concentrated Engine Anti–Freezes by the Iodine Reagent Method | 571.116
|
| ASTM D 1193–70 Standard Specifications for Reagent Water | 571.116
|
| ASTM D 1415–68 Tentative Method of Test for International Hardness of Volcanized Natural and Synthetic Rubbers | 571.116
|
| ASTM D 1564–71 Standard Method of Testing Flexible Cellular Materials—Slab Urethane Foam | 571.213
|
| ASTM D 1565–76 Standard Specifications for Flexible Cellular Materials—Vinyl Chloride Polymers and Copolymers (Open–Cell Foam) | 571.213
|
| ASTM D 2343–67, (Reapproved 1985), Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics | 571.5; 571.304
|
| ASTM D 2344–84, (Reapproved 1989), Standard Test Method for Apparent Interlaminar Shear Strength of Parallel Fiber Composites by Short–Beam Method | 571.5; 571.304
|
| ASTM D 2515–66 Standard Specifications for Kinematic Glass Viscosity | 571.116
|
| ASTM D 4329–99, Standard Practice for Fluorescent UV Exposure of Plastics | 571.106, S12.7
|
| ASTM E 1–68 Standard Specifications for ASTM Thermometers | 571.116
|
| ASTM E 4–64 Methods of Verification of Testing Machines | 571.106; 571.209
|
| ASTM E 4–72 Methods of Verification of Testing Machines | 571.221
|
| ASTM E 4–79 Standard Methods of Load Verification of Testing Machines | 571.209
|
| ASTM E 4–03 Standard Practices for Force Verification of Testing Machines | 571.106, S6.4, 571.106, S8.9
|
| ASTM E 8–93, Standard Test Methods for Tension Testing of Metallic Materials | 571.5; 571.304
|
| ASTM E 77–66 Standard Method for Inspection, Test and Standardization of Liquid–in–Glass Thermometers | 571.116
|
| ASTM E 274–65T Skid Resistance of Pavements Using a Two Wheel Trailer | 571.208; 571.301
|
| ASTM E 274–79 Standard Test Method for Skid Resistance of Paved Surfaces Using a Full–Scale Tire | 571.105; 571.116
|
| ASTM E 298–68 Standard Methods for Assay of Organic Peroxides | 571.116
|
| ASTM E 1136–93 (1993), Standard Specification for a Radial Standard Reference Test Tire | 571.126; 571.500
|
| ASTM E 1137–90, Standard Test Method for Determining Longitudinal Peak Braking Coefficient of Paved Surfaces Using a Standard Reference Test Tire | 571.500
|
| ASTM E1337–90 (Reapproved 1996), Standard Test Method for Determining Longitudinal Peak Braking Coefficient of Paved Surfaces Using a Standard Reference Test Tire | 571.126
|
| ASTM G 23–81 Standard Practice for Operating Light Exposure Apparatus (Carbon Arc Type) with and without Water for Exposure of Nonmetallic Materials | 571.209
|
| ASTM G 151–97 Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources | 571.106, S12.7
|
| ASTM G 154–00 Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials | 571.106, S12.7
|
| 1985 Annual Book of ASTM Standards, Vol. 5.04, “Motor Fuels”, Section I, A2.3.2, A2.3.3. and A2.7 in Annex 2 | 571.108; 571.205
|
General Services Administration
Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402, Telephone 202–512–1800
|
| Federal Specification L–S–300 1965, Sheeting and Tape Reflective: Nonexposed Lens, Adhesive Backing | 571.108
|
Illuminating Engineering Society of North America
345 East 47th St., New York, NY 10017
|
| LM–45 IES Approved Method for Electrical and Photometric Measurements of General Service Incandescent Filament Lamps (April 1980) | 571.108
|
Leet–Melbrook
18810 Woodfield Road, Gaithersburg, Maryland20879(301)670–0090
|
| NHTSA 213–2003, FMVSS No. 213, dated June 3, 2003, NHTSA Standard Seat Assembly Drawing Package, including of drawings and a bill of materials:
|
| Drawing Package Cover Sheet, Drawing Package: NHTSA Standard Seat Assembly, FMVSS No. 213, NO. NHTSA–213–2003, dated June 3, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA100, Seat Assembly, NHTSA Seat, May 14, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA200, Frame Assembly, NHTSA Seat, May 14, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA201, Frame, Front and Side Assembly, NHTSA Seat, May 7, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA202, Frame, Bottom Assembly, NHTSA Seat, May 14, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA203, Frame, Top Assembly, NHTSA Seat, May 7, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA204, Anchor Points Assembly, NHTSA Seat, May 14, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA205, Frame, Back Assembly, NHTSA Seat, May 7, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA300, Cushion Assembly, NHTSA Seat, May 21, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA301, Cushion, Seat Assembly, NHTSA Seat, May 7, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA302, Cushion, Back Assembly, NHTSA Seat, May 21, 2003 | 571.5; 571.213
|
| Drawing No. 2003HA303, Backing, Seat and Back Assembly, NHTSA Seat, May 21, 2003 | 571.5; 571.213
|
National Aeronautics and Space Administration
600 Independence Ave. SW., Washington, DC 20546
|
| NASA NAS 3–6292, Computer Program for the Analysis of Filament–Reinforced Metal–Shell Pressure Vessels (May 1966) | 571.5; 571.304
|
Department of Defense
DODSSP Standardization Document Order Desk, 700 Robbins Ave., Bldg , Philadelphia, PA 19111–5098
|
| Military Specifications:
|
| MIL–S–13192, Shoes, Men's, Dress, 1976 | 571.208; 571.214
|
| MIL–S–13192P, 1988,“Military Specification, Shoes, Men's Dress, Oxford,” Amendment 1, October 14, 1994 | 571.208
|
| MIL–S–21711E, 1982,“Military Specification, Shoes, Women's,” Amendment 2, October 14, 1994 | 571.208
|
National Health Survey Data
Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402, Telephone 202–512–1800
|
| 5th Percentile adult female and 95th Percentile adult male: Public Health Service Pub. No. 1000, Series 11, No. 8, “Weight, Height, and Selected Body Dimensions of Adults”, 1965 | 571.3
|
National Highway Traffic Safety Administration
Office of Vehicle Safety Standards, DOT–NHTSA, 400 7th St. SW., Washington, DC 20590
|
| Drawing Package, SAS–100–1000, Standard Seat Assembly with Addendum A, Seat Base Weldment, dated July 1, 1993 | 571.213
|
| Drawing Package, SAS–100–1000, Addendum A, Seat Base Weldment, dated October 23, 1998 | 571.213
|
Society of Automotive Engineers
400 Commonwealth Dr., Warrendale, PA 15096–0001, Telephone: (412) 776–4841
|
| SAE Recommended Practice J100, Class A Vehicle Glazing Shade Bands, 1995 | 571.5; 571.205
|
| SAE J186a Supplemental High Mounted Stop and Rear Turn Signal Lamps, September 1977 | 571.108
|
| SAE J211–1980 Instrumentation for Impact Tests | 571.218
|
| SAE J211/1, Revised March 1995: “Instrumentation for Impact Tests— Part 1: Electronic Instrumentation” | 563.4; 563.8; 571.5; 571.202a; 571.208; 571.403
|
| SAE J211/1, Revised December 2003, “Instrumentation for Impact Tests—Part 1: Electronic Instrumentation” | 571.5; 571.209
|
| SAE J211a–1971 Instrumentation for Impact Tests | 571.213; 571.222
|
| SAE J222–1970 Parking Lamps (Position Lamps) | 571.108
|
| SAE J387–NOV 1987 Terminology–Motor Vehicle Lighting | Part 571
|
| SAE J527–1967 Brazed Double Wall Low Carbon Steel Tubing | 571.116
|
| SAE J564a–1964 Headlamp Beam Switching | 571.108
|
| SAE J565b–1969 Semi–Automatic Headlamp Beam Switching Devices | 571.108
|
| SAE J566–1960 Headlamp Mountings | 571.108
|
| SAE J567b–1970 Bulb Sockets | 571.108
|
| SAE J571d–1976 Dimensional Specification for Sealed Beam Headlamp Units | 571.108
|
| SAE J573d–1968 Lamp Bulbs and Sealed Units | 571.108
|
| SAE J575, July 1983, Tests for Motor Vehicle Lighting Devices and Components | 571.131
|
| SAE J575d–1967 Test for Motor Vehicle Lighting Devices and Components | 571.108
|
| SAE J575e–1970 Test for Motor Vehicle Lighting Devices and Components | 571.108
|
| SAE J576 JUL91 Plastic Materials for Use in Optical Parts, such as Lenses and Reflectors, of Motor Vehicle Lighting Devices | 571.108
|
| SAE J578, May 1988, Color Specification | 571.131
|
| SAE J578, June 1995, Color Specification | 571.5; 571.403
|
| SAE J578c–1977 Color Specification for Electric Signal Lighting Devices | 571.108
|
| SAE J578 MAY88 Color Specification for Electric Signal Lighting Devices | 571.108
|
| SAE J580–1986 Sealed Beam Headlamp Assembly | 571.108
|
| SAE J584–1964 Motorcycle and Motor Driven Cycle Headlamps | 571.108
|
| SAE J585d–1970 Tail Lamps (Rear Position Light) | 571.108
|
| SAE J585e–1977 Tail Lamps (Rear Position Lamps) | 571.108
|
| SAE J586b–1966 Stop Lamps | 571.108
|
| SAE J586c–1970 Stop Lamps | 571.108
|
| SAE J586 FEB84 Stop Lamps for Use on Motor Vehicles Less than 2032 mm in Overall Width | 571.108
|
| SAE J587–1981 License Plate Lamps (Rear Registration Plate Lamps) | 571.108
|
| SAE J588d–1966 Turn Signal Lamps | 571.108
|
| SAE J588e–1970 Turn Signal Lamps | 571.108
|
| SAE J588 NOV84 Turn Signal Lamps for Use on Motor Vehicles Less than 2032 mm in Overall Width | 571.108
|
| SAE J589–1964 Turn Signal Switch | 571.108
|
| SAE J590b–1965 Automotive Turn Signal Flashers | 571.108
|
| SAE J592–1992 Clearance, Side Marker and Identification Lamps | 571.121
|
| SAE J592e–1972 Clearance, Side Marker and Identification Lamps | 571.108; 571.121
|
| SAE J593c–1968 Backup Lamps | 571.108
|
| SAE J594f–1977 Reflex Reflectors | 571.108
|
| SAE J599b–1970 Lighting Inspection Code | 581.5(c)
|
| SAE J599c–1973 Lighting Inspection Code | 571.108
|
| SAE J602–1980 Headlamps Aiming Device for Mechanically Aimable Sealed Beam Headlamp Units | 571.108
|
| SAE J673–1993 Automotive Safety Glasses | 571.5; 571.205
|
| SAE J726a–1962 Recommended Practice, Air Cleaner Test Code | 571.209
|
| SAE J759–1995 Recommended Practice, Lighting Identification Code | 571.121
|
| SAE J787(g) 1966 Motor Vehicle Seat Belt Anchorage | 571.3
|
| SAE J800b–1965 Recommended Practice, Motor Vehicle Seat Belt Installations | 571.209
|
| SAE J826–Nov.1962 Manikins for Use in Defining Vehicle Seating Accomodations | 571.3(b)(3)
|
| SAE J826–1980 Devices for Use in Defining Vehicle Seating Accommodations | 571.3; 571.108; 571.208; 571.214
|
| SAE J826–May 87 Devices for Use in Defining and Measuring Vehicle Seating Accomodation | 571.210
|
| SAE J826–1992 Devices for Use in Defining and Measuring Vehicle Seating Accomodations | 571.225
|
| SAE J826–revised 1995 Devices for Use in Defining and Measuring Vehicle Seating Accomodations | 571.202a
|
| SAE J839b–1965 Passenger Car Side Door Latch System | 571.201; 571.206
|
| SAE J885a–1966 Human Tolerance to Impact Conditions as Related to Motor Vehicle Design | 571.208
|
| SAE J887–1964 School Bus Red Signal Lamps | 571.108
|
| SAE J902–1964 Recommended Practice, Passenger Car Windshield Defrosting Systems | 571.103
|
| SAE J902a–1967 Passenger Car Windshield Defrosting Systems | 571.103
|
| SAE J903a–1966 Passenger Car Windshield Wiper Systems | 571.104
|
| SAE J910–1966 Vehicle Hazard Warning Signal Flasher | 571.108
|
| SAE J921–1965 Recommended Practice, Instrument Panel Laboratory Impact Test Procedure | 571.201
|
| SAE J934–1965 Recommended Practice Vehicle Passenger Door Hinge Systems | 571.206
|
| SAE J941–1965 Passenger Car Driver's Eye Range | 571.104; 571.107
|
| SAE J942–1965 Passenger Car Windshield Washer System | 571.104
|
| SAE J944–JUN80 Steering Control System–Passenger Car–Laboratory Test Procedure | 571.203
|
| SAE J945b–1966 Vehicular Hazard Warning Signal Flashers | 571.108
|
| SAE J964a–1974 Test Procedure for Determining Reflectivity of Rear View Mirrors | 571.111
|
| SAE J972–1966 (Revised May 2000) Moving Rigid Barrier Collision Tests | 571.105
|
| SAE J977–1966 Instrumentation for Laboratory Impact Tests | 571.201
|
| SAE J1100a Motor Vehicle Dimensions | 571.3
|
| SAE J1100 Jun84 Motor Vehicle Dimensions | 571.210
|
| SAE J1100–1993 Recommended Practice, Motor Vehicle Dimensions | 571.225
|
| SAE J1132–1976 Sealed Beam Headlamp Units | 571.108
|
| SAE J1133, April 1984, School Bus Stop Arm | 571.131
|
| SAE J1383–1985 Performance Requirements for Motor Vehicle Headlamps | 571.108
|
| SAE J1395 APR85 Turn Signal Lamps for Use on Motor Vehicles 2032mm or More in Overall Width | 571.108
|
| SAE J1398 MAY85 Stop Lamps for Use on Motor Vehicles 2032 mm or More in Overall Width | 571.108
|
| SAE J1703 JAN 1995, Motor Vehicle Brake Fluid, Appendix B, SAE RM–66–04 Compatibility Fluid | 571.106; 571.116
|
| SAE J1733 1994–12, Information Report “Sign Convention for Vehicle Crash Testing,”, December 1994 | 571.121; Part 572, Subpart M; 572.120; 572.137; 572.140; 572.146; 572.150; 572.155
|
| SAE RM–66–04, Compatibility Fluid, Appendix B of SAE J1703, revised January 1995 | 571,106, S5.3.9, 571.106, S6.10.2
|
| ANSI/SAE Z26.1, American National Standard for Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways—Safety Standard, 1996 | 571.5; 571.205
|
| SAE Aero Space and Car and Body Measuring Standard | 571.202
|
Suppliers of Advanced Composite Materials Association
1600 Wilson Blvd., Suite 1008, Arlington, VA 22209
|
| SACMA SRM 16–90, Recommended Test Method for Tow Tensile Testing of Carbon Fibers | 571.5; 571.304
|
United Nations
Conference Services Division, Distribution and Sales Section, Office C.115–1, Palais des Nations, CH–1211, Geneva 10, Switzerland, http://www.unece.org/trans/main/wp29/wp29regs.html
|
| “Uniform Provisions Concerning the Approval of Vehicles with Regard to the Installation of Lighting and Light–Signalling Devices”, Economic Commission for Europe Regulation 48:E/ECE/324–E/ECE/TRANS/505, Rev.1/Add.47/Rev.1/Corr.2, p.17 (February 26, 1996) | 571.5; 571.108
|
| Regulation No. 17: Uniform Provisions Concerning the Approval of Vehicles with regard to the Seats, their Anchorages, and any Head Restraints, Revision 4, dated July 31, 2002 | 571.202 |
