e-CFR Navigation Aids Advanced Search — Boolean
Related Resources |
## Electronic Code of Federal Regulations
Title 46: Shipping
## Subpart G—Special Rules Pertaining to a Ship That Carries a Bulk Liquefied Gas Regulated Under Subchapter O of This ChapterContents §172.155 Specific applicability. §172.160 Definitions. §172.165 Intact stability calculations. §172.170 Damage stability calculations. §172.175 Character of damage. §172.180 Extent of damage. §172.185 Permeability of spaces. §172.195 Survival conditions. §172.205 Local damage. ## §172.155 Specific applicability.This subpart applies to each tankship that has on board a bulk liquefied gas listed in Table 4 of part 154 of this chapter as cargo, cargo residue, or vapor. ## §172.160 Definitions.As used in this subpart— (a) Length or L means the load line length (LLL). (b) MARVS means the Maximum Allowable Relief Valve Setting of a cargo tank. ## §172.165 Intact stability calculations.(a) Design calculations must show that 2 inches (50mm) of positive metacentric height can be maintained by each tankship when it is being loaded and unloaded. (b) For the purpose of demonstrating compliance with the requirements of paragraph (a) of this section, the effects of the addition of water ballast may be considered. ## §172.170 Damage stability calculations.(a) Each tankship must be shown by design calculations to meet the survival conditions in §172.195 in each condition of loading and operation assuming the damage specified in §172.175 for the hull type specified in Table 4 of part 154 of this chapter. (b) If a cargo listed in Table 4 of part 154 of this chapter is to be carried, the vessel must be at least the ship type specified in Table 4 of part 154 of this chapter for the cargo. ## §172.175 Character of damage.(a) If a type IG hull is required, design calculations must show that the vessel can survive damage at any location. (b) If a type IIG hull is required, design calculations must show that a vessel— (1) Longer than 492 feet (150 meters) in length can survive damage at any location; and (2) 492 feet (150 meters) or less in length can survive damage at any location except the transverse bulkheads bounding an aft machinery space. The machinery space is calculated as a single floodable compartment. (c) If a vessel has independent tanks type C with a MARVS of 100 psi (689 kPa) gauge or greater, is 492 feet (150 meters) or less in length, and Table 4 of part 154 of this chapter allows a type IIPG hull, design calculations must show that the vessel can survive damage at any location, except as prescribed in paragraph (e) of this section. (d) If a type IIIG hull is required, except as specified in paragraph (e) of this section, design calculations must show that a vessel— (1) 410 feet (125 meters) in length or longer can survive damage at any location; and (2) Less than 410 feet (125 meters) in length can survive damage at any location, except in the main machinery space. (e) The calculations in paragraphs (c) and (d) of this section need not assume damage to a transverse bulkhead unless it is spaced closer than the longitudinal extent of collision penetration specified in Table 172.180 from another transverse bulkhead. (f) If a main transverse watertight bulkhead or transverse watertight bulkhead bounding a side tank or double bottom tank has a step or a recess that is longer than 10 feet (3.05 meters) located within the extent of penetration of assumed damage, the vessel must be shown by design calculations to survive damage to this bulkhead. The step formed by the after peak bulkhead and after peak tank top is not a step for the purpose of this regulation. ## §172.180 Extent of damage.For the purpose of §172.170— (a) Design calculations must include both side and bottom damage, applied separately; and (b) Damage must consist of the penetrations having the dimensions given in Table 172.180 except that, if the most disabling penetrations would be less than the penetrations given in Table 172.180, the smaller penetration must be assumed. Table 172.180—Extent of Damage
## §172.185 Permeability of spaces.(a) When doing the calculations required in §172.170, the permeability of a floodable space other than a machinery space must be as listed in Table 172.060(b). (b) Calculations in which a machinery space is treated as a floodable space must be based on an assumed machinery space permeability of 85%, unless the use of an assumed permeability of less than 85% is justified in detail. (c) If a cargo tank would be penetrated under the assumed damage, the cargo tank must be assumed to lose all cargo and refill with salt water up to the level of the tankship's final equilibrium waterline. ## §172.195 Survival conditions.A vessel is presumed to survive assumed damage if it meets the following conditions in the final stage of flooding: (a) Final waterline. The final waterline, in the final condition of sinkage, heel, and trim, must be below the lower edge of an opening through which progressive flooding may take place, such as an air pipe, or an opening that is closed by means of a weathertight door or hatch cover. This opening does not include an opening closed by a— (1) Watertight manhole cover; (2) Flush scuttle; (3) Small watertight cargo tank hatch cover that maintains the high integrity of the deck; (4) A Class 1 door in a watertight bulkhead within the superstructure; (5) Remotely operated sliding watertight door; or (6) A side scuttle of the non-opening type. (b) Heel angle. The maximum angle of heel must not exceed 30 degrees. (c) Range of stability. Through an angle of 20 degrees beyond its position of equilibrium after flooding, a tankship must meet the following conditions: (1) The righting arm curve must be positive. (2) The maximum righting arm must be at least 3.94 inches (10 cm). (3) Each submerged opening must be weathertight. (d) Progressive flooding. If pipes, ducts, or tunnels are within the assumed extent of damage, arrangements must be made to prevent progressive flooding to a space that is not assumed to be flooded in the damaged stability calculations. (e) Buoyancy of superstructure. The buoyancy of any superstructure directly above the side damage is to be disregarded. The unflooded parts of superstructures beyond the extent of damage may be taken into consideration if they are separated from the damaged space by watertight bulkheads and no progressive flooding of these intact spaces takes place. (f) Metacentric height. After flooding, the tank ship's metacentric height must be at least 2 inches (50 mm) when the vessel is in the upright position. (g) Equalization arrangements. Equalization arrangements requiring mechanical aids such as valves or cross-flooding lines may not be considered for reducing the angle of heel. Spaces joined by ducts of large cross-sectional area are treated as common spaces. (h) Intermediate stages of flooding. If an intermediate stage of flooding is more critical than the final stage, the tank vessel must be shown by design calculations to meet the requirements in this section in the intermediate stage. ## §172.205 Local damage.(a) Each tankship must be shown by design calculations to meet the survival conditions in paragraph (b) of this section in each condition of loading and operation assuming that local damage extending 30 inches (76 cm) normal to the hull shell is applied at any location in the cargo length: (b) The vessel is presumed to survive assumed local damage if it does not heel beyond the smaller of the following angles in the final stage of flooding: (1) 30 degrees. (2) The angle at which restoration of propulsion and steering, and use of the ballast system is precluded. |