About GPO   |   Newsroom/Media   |   Congressional Relations   |   Inspector General   |   Careers   |   Contact   |   askGPO   |   Help  
 
Home   |   Customers   |   Vendors   |   Libraries  

The Electronic Code of Federal Regulations (e-CFR) is a regularly updated, unofficial editorial compilation of CFR material and Federal Register amendments produced by the National Archives and Records Administration's Office of the Federal Register (OFR) and the Government Printing Office.

Parallel Table of Authorities and Rules for the Code of Federal Regulations and the United States Code
Text | PDF

Find, review, and submit comments on Federal rules that are open for comment and published in the Federal Register using Regulations.gov.

Purchase individual CFR titles from the U.S. Government Online Bookstore.

Find issues of the CFR (including issues prior to 1996) at a local Federal depository library.

[1]
 
 

Electronic Code of Federal Regulations

e-CFR Data is current as of October 22, 2014

Title 40Chapter ISubchapter C → Part 60


Title 40: Protection of Environment


PART 60—STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES


Contents

Subpart A—General Provisions

§60.1   Applicability.
§60.2   Definitions.
§60.3   Units and abbreviations.
§60.4   Address.
§60.5   Determination of construction or modification.
§60.6   Review of plans.
§60.7   Notification and record keeping.
§60.8   Performance tests.
§60.9   Availability of information.
§60.10   State authority.
§60.11   Compliance with standards and maintenance requirements.
§60.12   Circumvention.
§60.13   Monitoring requirements.
§60.14   Modification.
§60.15   Reconstruction.
§60.16   Priority list.
§60.17   Incorporations by reference.
§60.18   General control device and work practice requirements.
§60.19   General notification and reporting requirements.
Table 1 to Subpart A of Part 60-Detection Sensitivity Levels (grams per hour)

Subpart B—Adoption and Submittal of State Plans for Designated Facilities

§60.20   Applicability.
§60.21   Definitions.
§60.22   Publication of guideline documents, emission guidelines, and final compliance times.
§60.23   Adoption and submittal of State plans; public hearings.
§60.24   Emission standards and compliance schedules.
§60.25   Emission inventories, source surveillance, reports.
§60.26   Legal authority.
§60.27   Actions by the Administrator.
§60.28   Plan revisions by the State.
§60.29   Plan revisions by the Administrator.

Subpart C—Emission Guidelines and Compliance Times

§60.30   Scope.
§60.31   Definitions.

Subpart Ca [Reserved]

Subpart Cb—Emissions Guidelines and Compliance Times for Large Municipal Waste Combustors That are Constructed on or Before September 20, 1994

§60.30b   Scope and delegation of authority.
§60.31b   Definitions.
§60.32b   Designated facilities.
§60.33b   Emission guidelines for municipal waste combustor metals, acid gases, organics, and nitrogen oxides.
§60.34b   Emission guidelines for municipal waste combustor operating practices.
§60.35b   Emission guidelines for municipal waste combustor operator training and certification.
§60.36b   Emission guidelines for municipal waste combustor fugitive ash emissions.
§60.37b   Emission guidelines for air curtain incinerators.
§60.38b   Compliance and performance testing.
§60.39b   Reporting and recordkeeping guidelines and compliance schedules.
Table 1 to Subpart Cb of Part 60—Nitrogen Oxides Guidelines for Designated Facilities
Table 2 to Subpart Cb of Part 60—Nitrogen Oxides Limits for Existing Designated Facilities Included in an Emissions Averaging Plan at a Municipal Waste Combustor Plant
Table 3 to Subpart Cb of Part 60—Municipal Waste Combustor Operating Guidelines

Subpart Cc—Emission Guidelines and Compliance Times for Municipal Solid Waste Landfills

§60.30c   Scope.
§60.31c   Definitions.
§60.32c   Designated facilities.
§60.33c   Emission guidelines for municipal solid waste landfill emissions.
§60.34c   Test methods and procedures.
§60.35c   Reporting and recordkeeping guidelines.
§60.36c   Compliance times.

Subpart Cd—Emissions Guidelines and Compliance Times for Sulfuric Acid Production Units

§60.30d   Designated facilities.
§60.31d   Emissions guidelines.
§60.32d   Compliance times.

Subpart Ce—Emission Guidelines and Compliance Times for Hospital/Medical/Infectious Waste Incinerators

§60.30e   Scope.
§60.31e   Definitions.
§60.32e   Designated facilities.
§60.33e   Emissions guidelines.
§60.34e   Operator training and qualification guidelines.
§60.35e   Waste management guidelines.
§60.36e   Inspection guidelines.
§60.37e   Compliance, performance testing, and monitoring guidelines.
§60.38e   Reporting and recordkeeping guidelines.
§60.39e   Compliance times.
Table 1A to Subpart Ce of Part 60—Emissions Limits for Small, Medium, and Large HMIWI at Designated Facilities as Defined in §60.32e(a)(1)
Table 1B to Subpart Ce of Part 60—Emissions Limits for Small, Medium, and Large HMIWI at Designated Facilities as Defined in §60.32e(a)(1) and (a)(2)
Table 2A to Subpart Ce of Part 60—Emissions Limits for Small HMIWI Which Meet the Criteria Under §60.33e(b)(1)
Table 2B to Subpart Ce of Part 60—Emissions Limits for Small HMIWI Which Meet the Criteria Under §60.33e(b)(2)

Subpart D—Standards of Performance for Fossil-Fuel-Fired Steam Generators

§60.40   Applicability and designation of affected facility.
§60.41   Definitions.
§60.42   Standard for particulate matter (PM).
§60.43   Standard for sulfur dioxide (SO2).
§60.44   Standard for nitrogen oxides (NOX).
§60.45   Emissions and fuel monitoring.
§60.46   Test methods and procedures.

Subpart Da—Standards of Performance for Electric Utility Steam Generating Units

§60.40Da   Applicability and designation of affected facility.
§60.41Da   Definitions.
§60.42Da   Standards for particulate matter (PM).
§60.43Da   Standards for sulfur dioxide (SO2).
§60.44Da   Standards for nitrogen oxides (NOX).
§60.45Da   Alternative standards for combined nitrogen oxides (NOX) and carbon monoxide (CO).
§60.46Da   [Reserved]
§60.47Da   Commercial demonstration permit.
§60.48Da   Compliance provisions.
§60.49Da   Emission monitoring.
§60.50Da   Compliance determination procedures and methods.
§60.51Da   Reporting requirements.
§60.52Da   Recordkeeping requirements.

Subpart Db—Standards of Performance for Industrial-Commercial-Institutional Steam Generating Units

§60.40b   Applicability and delegation of authority.
§60.41b   Definitions.
§60.42b   Standard for sulfur dioxide (SO2).
§60.43b   Standard for particulate matter (PM).
§60.44b   Standard for nitrogen oxides (NOX).
§60.45b   Compliance and performance test methods and procedures for sulfur dioxide.
§60.46b   Compliance and performance test methods and procedures for particulate matter and nitrogen oxides.
§60.47b   Emission monitoring for sulfur dioxide.
§60.48b   Emission monitoring for particulate matter and nitrogen oxides.
§60.49b   Reporting and recordkeeping requirements.

Subpart Dc—Standards of Performance for Small Industrial-Commercial-Institutional Steam Generating Units

§60.40c   Applicability and delegation of authority.
§60.41c   Definitions.
§60.42c   Standard for sulfur dioxide (SO2).
§60.43c   Standard for particulate matter (PM).
§60.44c   Compliance and performance test methods and procedures for sulfur dioxide.
§60.45c   Compliance and performance test methods and procedures for particulate matter.
§60.46c   Emission monitoring for sulfur dioxide.
§60.47c   Emission monitoring for particulate matter.
§60.48c   Reporting and recordkeeping requirements.

Subpart E—Standards of Performance for Incinerators

§60.50   Applicability and designation of affected facility.
§60.51   Definitions.
§60.52   Standard for particulate matter.
§60.53   Monitoring of operations.
§60.54   Test methods and procedures.

Subpart Ea—Standards of Performance for Municipal Waste Combustors for Which Construction Is Commenced After December 20, 1989 and On or Before September 20, 1994

§60.50a   Applicability and delegation of authority.
§60.51a   Definitions.
§60.52a   Standard for municipal waste combustor metals.
§60.53a   Standard for municipal waste combustor organics.
§60.54a   Standard for municipal waste combustor acid gases.
§60.55a   Standard for nitrogen oxides.
§60.56a   Standards for municipal waste combustor operating practices.
§60.57a   [Reserved]
§60.58a   Compliance and performance testing.
§60.59a   Reporting and recordkeeping requirements.

Subpart Eb—Standards of Performance for Large Municipal Waste Combustors for Which Construction is Commenced After September 20, 1994 or for Which Modification or Reconstruction is Commenced After June 19, 1996

§60.50b   Applicability and delegation of authority.
§60.51b   Definitions.
§60.52b   Standards for municipal waste combustor metals, acid gases, organics, and nitrogen oxides.
§60.53b   Standards for municipal waste combustor operating practices.
§60.54b   Standards for municipal waste combustor operator training and certification.
§60.55b   Standards for municipal waste combustor fugitive ash emissions.
§60.56b   Standards for air curtain incinerators.
§60.57b   Siting requirements.
§60.58b   Compliance and performance testing.
§60.59b   Reporting and recordkeeping requirements.

Subpart Ec—Standards of Performance for New Stationary Sources: Hospital/Medical/Infectious Waste Incinerators

§60.50c   Applicability and delegation of authority.
§60.51c   Definitions.
§60.52c   Emission limits.
§60.53c   Operator training and qualification requirements.
§60.54c   Siting requirements.
§60.55c   Waste management plan.
§60.56c   Compliance and performance testing.
§60.57c   Monitoring requirements.
§60.58c   Reporting and recordkeeping requirements.
Table 1A to Subpart Ec of Part 60—Emissions Limits for Small, Medium, and Large HMIWI at Affected Facilities as Defined in §60.50c(a)(1) and (2)
Table 1B to Subpart Ec of Part 60—Emissions Limits for Small, Medium, and Large HMIWI at Affected Facilities as Defined in §60.50c(a)(3) and (4)
Table 2 of Subpart Ec of Part 60—Toxic Equivalency Factors
Table 3 to Subpart Ec of Part 60—Operating Parameters To Be Monitored and Minimum Measurement and Recording Frequencies

Subpart F—Standards of Performance for Portland Cement Plants

§60.60   Applicability and designation of affected facility.
§60.61   Definitions.
§60.62   Standards.
§60.63   Monitoring of operations.
§60.64   Test methods and procedures.
§60.65   Recordkeeping and reporting requirements.
§60.66   Delegation of authority.

Subpart G—Standards of Performance for Nitric Acid Plants

§60.70   Applicability and designation of affected facility.
§60.71   Definitions.
§60.72   Standard for nitrogen oxides.
§60.73   Emission monitoring.
§60.74   Test methods and procedures.

Subpart Ga—Standards of Performance for Nitric Acid Plants for Which Construction, Reconstruction, or Modification Commenced After October 14, 2011

§60.70a   Applicability and designation of affected facility.
§60.71a   Definitions.
§60.72a   Standards.
§60.73a   Emissions testing and monitoring.
§60.74a   Affirmative defense for violations of emission standards during malfunction.
§60.75a   Calculations.
§60.76a   Recordkeeping.
§60.77a   Reporting.

Subpart H—Standards of Performance for Sulfuric Acid Plants

§60.80   Applicability and designation of affected facility.
§60.81   Definitions.
§60.82   Standard for sulfur dioxide.
§60.83   Standard for acid mist.
§60.84   Emission monitoring.
§60.85   Test methods and procedures.

Subpart I—Standards of Performance for Hot Mix Asphalt Facilities

§60.90   Applicability and designation of affected facility.
§60.91   Definitions.
§60.92   Standard for particulate matter.
§60.93   Test methods and procedures.

Subpart J—Standards of Performance for Petroleum Refineries

§60.100   Applicability, designation of affected facility, and reconstruction.
§60.101   Definitions.
§60.102   Standard for particulate matter.
§60.103   Standard for carbon monoxide.
§60.104   Standards for sulfur oxides.
§60.105   Monitoring of emissions and operations.
§60.106   Test methods and procedures.
§60.107   Reporting and recordkeeping requirements.
§60.108   Performance test and compliance provisions.
§60.109   Delegation of authority.

Subpart Ja—Standards of Performance for Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007

§60.100a   Applicability, designation of affected facility, and reconstruction.
§60.101a   Definitions.
§60.102a   Emissions limitations.
§60.103a   Design, equipment, work practice or operational standards.
§60.104a   Performance tests.
§60.105a   Monitoring of emissions and operations for fluid catalytic cracking units (FCCU) and fluid coking units (FCU).
§60.106a   Monitoring of emissions and operations for sulfur recovery plants.
§60.107a   Monitoring of emissions and operations for fuel gas combustion devices and flares.
§60.108a   Recordkeeping and reporting requirements.
§60.109a   Delegation of authority.
Table 1 to Subpart Ja of Part 60—Molar Exhaust Volumes and Molar Heat Content of Fuel Gas Constituents

Subpart K—Standards of Performance for Storage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978

§60.110   Applicability and designation of affected facility.
§60.111   Definitions.
§60.112   Standard for volatile organic compounds (VOC).
§60.113   Monitoring of operations.

Subpart Ka—Standards of Performance for Storage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984

§60.110a   Applicability and designation of affected facility.
§60.111a   Definitions.
§60.112a   Standard for volatile organic compounds (VOC).
§60.113a   Testing and procedures.
§60.114a   Alternative means of emission limitation.
§60.115a   Monitoring of operations.

Subpart Kb—Standards of Performance for Volatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984

§60.110b   Applicability and designation of affected facility.
§60.111b   Definitions.
§60.112b   Standard for volatile organic compounds (VOC).
§60.113b   Testing and procedures.
§60.114b   Alternative means of emission limitation.
§60.115b   Reporting and recordkeeping requirements.
§60.116b   Monitoring of operations.
§60.117b   Delegation of authority.

Subpart L—Standards of Performance for Secondary Lead Smelters

§60.120   Applicability and designation of affected facility.
§60.121   Definitions.
§60.122   Standard for particulate matter.
§60.123   Test methods and procedures.

Subpart M—Standards of Performance for Secondary Brass and Bronze Production Plants

§60.130   Applicability and designation of affected facility.
§60.131   Definitions.
§60.132   Standard for particulate matter.
§60.133   Test methods and procedures.

Subpart N—Standards of Performance for Primary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973

§60.140   Applicability and designation of affected facility.
§60.141   Definitions.
§60.142   Standard for particulate matter.
§60.143   Monitoring of operations.
§60.144   Test methods and procedures.

Subpart Na—Standards of Performance for Secondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983

§60.140a   Applicability and designation of affected facilities.
§60.141a   Definitions.
§60.142a   Standards for particulate matter.
§60.143a   Monitoring of operations.
§60.144a   Test methods and procedures.
§60.145a   Compliance provisions.

Subpart O—Standards of Performance for Sewage Treatment Plants

§60.150   Applicability and designation of affected facility.
§60.151   Definitions.
§60.152   Standard for particulate matter.
§60.153   Monitoring of operations.
§60.154   Test methods and procedures.
§60.155   Reporting.
§60.156   Delegation of authority.

Subpart P—Standards of Performance for Primary Copper Smelters

§60.160   Applicability and designation of affected facility.
§60.161   Definitions.
§60.162   Standard for particulate matter.
§60.163   Standard for sulfur dioxide.
§60.164   Standard for visible emissions.
§60.165   Monitoring of operations.
§60.166   Test methods and procedures.

Subpart Q—Standards of Performance for Primary Zinc Smelters

§60.170   Applicability and designation of affected facility.
§60.171   Definitions.
§60.172   Standard for particulate matter.
§60.173   Standard for sulfur dioxide.
§60.174   Standard for visible emissions.
§60.175   Monitoring of operations.
§60.176   Test methods and procedures.

Subpart R—Standards of Performance for Primary Lead Smelters

§60.180   Applicability and designation of affected facility.
§60.181   Definitions.
§60.182   Standard for particulate matter.
§60.183   Standard for sulfur dioxide.
§60.184   Standard for visible emissions.
§60.185   Monitoring of operations.
§60.186   Test methods and procedures.

Subpart S—Standards of Performance for Primary Aluminum Reduction Plants

§60.190   Applicability and designation of affected facility.
§60.191   Definitions.
§60.192   Standard for fluorides.
§60.193   Standard for visible emissions.
§60.194   Monitoring of operations.
§60.195   Test methods and procedures.

Subpart T—Standards of Performance for the Phosphate Fertilizer Industry: Wet-Process Phosphoric Acid Plants

§60.200   Applicability and designation of affected facility.
§60.201   Definitions.
§60.202   Standard for fluorides.
§60.203   Monitoring of operations.
§60.204   Test methods and procedures.

Subpart U—Standards of Performance for the Phosphate Fertilizer Industry: Superphosphoric Acid Plants

§60.210   Applicability and designation of affected facility.
§60.211   Definitions.
§60.212   Standard for fluorides.
§60.213   Monitoring of operations.
§60.214   Test methods and procedures.

Subpart V—Standards of Performance for the Phosphate Fertilizer Industry: Diammonium Phosphate Plants

§60.220   Applicability and designation of affected facility.
§60.221   Definitions.
§60.222   Standard for fluorides.
§60.223   Monitoring of operations.
§60.224   Test methods and procedures.

Subpart W—Standards of Performance for the Phosphate Fertilizer Industry: Triple Superphosphate Plants

§60.230   Applicability and designation of affected facility.
§60.231   Definitions.
§60.232   Standard for fluorides.
§60.233   Monitoring of operations.
§60.234   Test methods and procedures.

Subpart X—Standards of Performance for the Phosphate Fertilizer Industry: Granular Triple Superphosphate Storage Facilities

§60.240   Applicability and designation of affected facility.
§60.241   Definitions.
§60.242   Standard for fluorides.
§60.243   Monitoring of operations.
§60.244   Test methods and procedures.

Subpart Y—Standards of Performance for Coal Preparation and Processing Plants

§60.250   Applicability and designation of affected facility.
§60.251   Definitions.
§60.252   Standards for thermal dryers.
§60.253   Standards for pneumatic coal-cleaning equipment.
§60.254   Standards for coal processing and conveying equipment, coal storage systems, transfer and loading systems, and open storage piles.
§60.255   Performance tests and other compliance requirements.
§60.256   Continuous monitoring requirements.
§60.257   Test methods and procedures.
§60.258   Reporting and recordkeeping.

Subpart Z—Standards of Performance for Ferroalloy Production Facilities

§60.260   Applicability and designation of affected facility.
§60.261   Definitions.
§60.262   Standard for particulate matter.
§60.263   Standard for carbon monoxide.
§60.264   Emission monitoring.
§60.265   Monitoring of operations.
§60.266   Test methods and procedures.

Subpart AA—Standards of Performance for Steel Plants: Electric Arc Furnaces Constructed After October 21, 1974, and On or Before August 17, 1983

§60.270   Applicability and designation of affected facility.
§60.271   Definitions.
§60.272   Standard for particulate matter.
§60.273   Emission monitoring.
§60.274   Monitoring of operations.
§60.275   Test methods and procedures.
§60.276   Recordkeeping and reporting requirements.

Subpart AAa—Standards of Performance for Steel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 17, 1983

§60.270a   Applicability and designation of affected facility.
§60.271a   Definitions.
§60.272a   Standard for particulate matter.
§60.273a   Emission monitoring.
§60.274a   Monitoring of operations.
§60.275a   Test methods and procedures.
§60.276a   Recordkeeping and reporting requirements.

Subpart BB—Standards of Performance for Kraft Pulp Mills

§60.280   Applicability and designation of affected facility.
§60.281   Definitions.
§60.282   Standard for particulate matter.
§60.283   Standard for total reduced sulfur (TRS).
§60.284   Monitoring of emissions and operations.
§60.285   Test methods and procedures.

Subpart BBa—Standards of Performance for Kraft Pulp Mill Affected Sources for Which Construction, Reconstruction, or Modification Commenced After May 23, 2013

§60.280a   Applicability and designation of affected facility.
§60.281a   Definitions.
§60.282a   Standard for filterable particulate matter.
§60.283a   Standard for total reduced sulfur (TRS).
§60.284a   Monitoring of emissions and operations.
§60.285a   Test methods and procedures.
§60.286a   Affirmative defense for violations of emission standards during malfunction.
§60.287a   Recordkeeping.
§60.288a   Reporting.

Subpart CC—Standards of Performance for Glass Manufacturing Plants

§60.290   Applicability and designation of affected facility.
§60.291   Definitions.
§60.292   Standards for particulate matter.
§60.293   Standards for particulate matter from glass melting furnace with modified-processes.
§§60.294-60.295   [Reserved]
§60.296   Test methods and procedures.

Subpart DD—Standards of Performance for Grain Elevators

§60.300   Applicability and designation of affected facility.
§60.301   Definitions.
§60.302   Standard for particulate matter.
§60.303   Test methods and procedures.
§60.304   Modifications.

Subpart EE—Standards of Performance for Surface Coating of Metal Furniture

§60.310   Applicability and designation of affected facility.
§60.311   Definitions and symbols.
§60.312   Standard for volatile organic compounds (VOC).
§60.313   Performance tests and compliance provisions.
§60.314   Monitoring of emissions and operations.
§60.315   Reporting and recordkeeping requirements.
§60.316   Test methods and procedures.

Subpart FF [Reserved]

Subpart GG—Standards of Performance for Stationary Gas Turbines

§60.330   Applicability and designation of affected facility.
§60.331   Definitions.
§60.332   Standard for nitrogen oxides.
§60.333   Standard for sulfur dioxide.
§60.334   Monitoring of operations.
§60.335   Test methods and procedures.

Subpart HH—Standards of Performance for Lime Manufacturing Plants

§60.340   Applicability and designation of affected facility.
§60.341   Definitions.
§60.342   Standard for particulate matter.
§60.343   Monitoring of emissions and operations.
§60.344   Test methods and procedures.

Subpart KK—Standards of Performance for Lead-Acid Battery Manufacturing Plants

§60.370   Applicability and designation of affected facility.
§60.371   Definitions.
§60.372   Standards for lead.
§60.373   Monitoring of emissions and operations.
§60.374   Test methods and procedures.

Subpart LL—Standards of Performance for Metallic Mineral Processing Plants

§60.380   Applicability and designation of affected facility.
§60.381   Definitions.
§60.382   Standard for particulate matter.
§60.383   Reconstruction.
§60.384   Monitoring of operations.
§60.385   Recordkeeping and reporting requirements.
§60.386   Test methods and procedures.

Subpart MM—Standards of Performance for Automobile and Light Duty Truck Surface Coating Operations

§60.390   Applicability and designation of affected facility.
§60.391   Definitions.
§60.392   Standards for volatile organic compounds.
§60.393   Performance test and compliance provisions.
§60.394   Monitoring of emissions and operations.
§60.395   Reporting and recordkeeping requirements.
§60.396   Reference methods and procedures.
§60.397   Modifications.
§60.398   Innovative technology waivers.

Subpart NN—Standards of Performance for Phosphate Rock Plants

§60.400   Applicability and designation of affected facility.
§60.401   Definitions.
§60.402   Standard for particulate matter.
§60.403   Monitoring of emissions and operations.
§60.404   Test methods and procedures.

Subpart PP—Standards of Performance for Ammonium Sulfate Manufacture

§60.420   Applicability and designation of affected facility.
§60.421   Definitions.
§60.422   Standards for particulate matter.
§60.423   Monitoring of operations.
§60.424   Test methods and procedures.

Subpart QQ—Standards of Performance for the Graphic Arts Industry: Publication Rotogravure Printing

§60.430   Applicability and designation of affected facility.
§60.431   Definitions and notations.
§60.432   Standard for volatile organic compounds.
§60.433   Performance test and compliance provisions.
§60.434   Monitoring of operations and recordkeeping.
§60.435   Test methods and procedures.

Subpart RR—Standards of Performance for Pressure Sensitive Tape and Label Surface Coating Operations

§60.440   Applicability and designation of affected facility.
§60.441   Definitions and symbols.
§60.442   Standard for volatile organic compounds.
§60.443   Compliance provisions.
§60.444   Performance test procedures.
§60.445   Monitoring of operations and recordkeeping.
§60.446   Test methods and procedures.
§60.447   Reporting requirements.

Subpart SS—Standards of Performance for Industrial Surface Coating: Large Appliances

§60.450   Applicability and designation of affected facility.
§60.451   Definitions.
§60.452   Standard for volatile organic compounds.
§60.453   Performance test and compliance provisions.
§60.454   Monitoring of emissions and operations.
§60.455   Reporting and recordkeeping requirements.
§60.456   Test methods and procedures.

Subpart TT—Standards of Performance for Metal Coil Surface Coating

§60.460   Applicability and designation of affected facility.
§60.461   Definitions.
§60.462   Standards for volatile organic compounds.
§60.463   Performance test and compliance provisions.
§60.464   Monitoring of emissions and operations.
§60.465   Reporting and recordkeeping requirements.
§60.466   Test methods and procedures.

Subpart UU—Standards of Performance for Asphalt Processing and Asphalt Roofing Manufacture

§60.470   Applicability and designation of affected facilities.
§60.471   Definitions.
§60.472   Standards for particulate matter.
§60.473   Monitoring of operations.
§60.474   Test methods and procedures.

Subpart VV—Standards of Performance for Equipment Leaks of VOC in the Synthetic Organic Chemicals Manufacturing Industry for which Construction, Reconstruction, or Modification Commenced After January 5, 1981, and on or Before November 7, 2006

§60.480   Applicability and designation of affected facility.
§60.481   Definitions.
§60.482-1   Standards: General.
§60.482-2   Standards: Pumps in light liquid service.
§60.482-3   Standards: Compressors.
§60.482-4   Standards: Pressure relief devices in gas/vapor service.
§60.482-5   Standards: Sampling connection systems.
§60.482-6   Standards: Open-ended valves or lines.
§60.482-7   Standards: Valves in gas/vapor service and in light liquid service.
§60.482-8   Standards: Pumps and valves in heavy liquid service, pressure relief devices in light liquid or heavy liquid service, and connectors.
§60.482-9   Standards: Delay of repair.
§60.482-10   Standards: Closed vent systems and control devices.
§60.483-1   Alternative standards for valves—allowable percentage of valves leaking.
§60.483-2   Alternative standards for valves—skip period leak detection and repair.
§60.484   Equivalence of means of emission limitation.
§60.485   Test methods and procedures.
§60.486   Recordkeeping requirements.
§60.487   Reporting requirements.
§60.488   Reconstruction.
§60.489   List of chemicals produced by affected facilities.

Subpart VVa—Standards of Performance for Equipment Leaks of VOC in the Synthetic Organic Chemicals Manufacturing Industry for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006

§60.480a   Applicability and designation of affected facility.
§60.481a   Definitions.
§60.482-1a   Standards: General.
§60.482-2a   Standards: Pumps in light liquid service.
§60.482-3a   Standards: Compressors.
§60.482-4a   Standards: Pressure relief devices in gas/vapor service.
§60.482-5a   Standards: Sampling connection systems.
§60.482-6a   Standards: Open-ended valves or lines.
§60.482-7a   Standards: Valves in gas/vapor service and in light liquid service.
§60.482-8a   Standards: Pumps, valves, and connectors in heavy liquid service and pressure relief devices in light liquid or heavy liquid service.
§60.482-9a   Standards: Delay of repair.
§60.482-10a   Standards: Closed vent systems and control devices.
§60.482-11a   Standards: Connectors in gas/vapor service and in light liquid service.
§60.483-1a   Alternative standards for valves—allowable percentage of valves leaking.
§60.483-2a   Alternative standards for valves—skip period leak detection and repair.
§60.484a   Equivalence of means of emission limitation.
§60.485a   Test methods and procedures.
§60.486a   Recordkeeping requirements.
§60.487a   Reporting requirements.
§60.488a   Reconstruction.
§60.489a   List of chemicals produced by affected facilities.

Subpart WW—Standards of Performance for the Beverage Can Surface Coating Industry

§60.490   Applicability and designation of affected facility.
§60.491   Definitions.
§60.492   Standards for volatile organic compounds.
§60.493   Performance test and compliance provisions.
§60.494   Monitoring of emissions and operations.
§60.495   Reporting and recordkeeping requirements.
§60.496   Test methods and procedures.

Subpart XX—Standards of Performance for Bulk Gasoline Terminals

§60.500   Applicability and designation of affected facility.
§60.501   Definitions.
§60.502   Standard for Volatile Organic Compound (VOC) emissions from bulk gasoline terminals.
§60.503   Test methods and procedures.
§60.504   [Reserved]
§60.505   Reporting and recordkeeping.
§60.506   Reconstruction.

Subpart AAA—Standards of Performance for New Residential Wood Heaters

§60.530   Applicability and designation of affected facility.
§60.531   Definitions.
§60.532   Standards for particulate matter.
§60.533   Compliance and certification.
§60.534   Test methods and procedures.
§60.535   Laboratory accreditation.
§60.536   Permanent label, temporary label, and owner's manual.
§60.537   Reporting and recordkeeping.
§60.538   Prohibitions.
§60.539   Hearing and appeal procedures.
§60.539a   Delegation of authority.
§60.539b   General provisions exclusions.

Subpart BBB—Standards of Performance for the Rubber Tire Manufacturing Industry

§60.540   Applicability and designation of affected facilities.
§60.541   Definitions.
§60.542   Standards for volatile organic compounds.
§60.542a   Alternate standard for volatile organic compounds.
§60.543   Performance test and compliance provisions.
§60.544   Monitoring of operations.
§60.545   Recordkeeping requirements.
§60.546   Reporting requirements.
§60.547   Test methods and procedures.
§60.548   Delegation of authority.

Subpart CCC [Reserved]

Subpart DDD—Standards of Performance for Volatile Organic Compound (VOC) Emissions from the Polymer Manufacturing Industry

§60.560   Applicability and designation of affected facilities.
§60.561   Definitions.
§60.562-1   Standards: Process emissions.
§60.562-2   Standards: Equipment leaks of VOC.
§60.563   Monitoring requirements.
§60.564   Test methods and procedures.
§60.565   Reporting and recordkeeping requirements.
§60.566   Delegation of authority.

Subpart EEE [Reserved]

Subpart FFF—Standards of Performance for Flexible Vinyl and Urethane Coating and Printing

§60.580   Applicability and designation of affected facility.
§60.581   Definitions and symbols.
§60.582   Standard for volatile organic compounds.
§60.583   Test methods and procedures.
§60.584   Monitoring of operations and recordkeeping requirements.
§60.585   Reporting requirements.

Subpart GGG—Standards of Performance for Equipment Leaks of VOC in Petroleum Refineries for which Construction, Reconstruction, or Modification Commenced After January 4, 1983, and on or Before November 7, 2006

§60.590   Applicability and designation of affected facility.
§60.591   Definitions.
§60.592   Standards.
§60.593   Exceptions.

Subpart GGGa—Standards of Performance for Equipment Leaks of VOC in Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006

§60.590a   Applicability and designation of affected facility.
§60.591a   Definitions.
§60.592a   Standards.
§60.593a   Exceptions.

Subpart HHH—Standards of Performance for Synthetic Fiber Production Facilities

§60.600   Applicability and designation of affected facility.
§60.601   Definitions.
§60.602   Standard for volatile organic compounds.
§60.603   Performance test and compliance provisions.
§60.604   Reporting requirements.

Subpart III—Standards of Performance for Volatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit Processes

§60.610   Applicability and designation of affected facility.
§60.611   Definitions.
§60.612   Standards.
§60.613   Monitoring of emissions and operations.
§60.614   Test methods and procedures.
§60.615   Reporting and recordkeeping requirements.
§60.616   Reconstruction.
§60.617   Chemicals affected by subpart III.
§60.618   Delegation of authority.

Subpart JJJ—Standards of Performance for Petroleum Dry Cleaners

§60.620   Applicability and designation of affected facility.
§60.621   Definitions.
§60.622   Standards for volatile organic compounds.
§60.623   Equivalent equipment and procedures.
§60.624   Test methods and procedures.
§60.625   Recordkeeping requirements.

Subpart KKK—Standards of Performance for Equipment Leaks of VOC From Onshore Natural Gas Processing Plants for Which Construction, Reconstruction, or Modification Commenced After January 20, 1984, and on or Before August 23, 2011

§60.630   Applicability and designation of affected facility.
§60.631   Definitions.
§60.632   Standards.
§60.633   Exceptions.
§60.634   Alternative means of emission limitation.
§60.635   Recordkeeping requirements.
§60.636   Reporting requirements.

Subpart LLL—Standards of Performance for SO2 Emissions From Onshore Natural Gas Processing for Which Construction, Reconstruction, or Modification Commenced After January 20, 1984, and on or Before August 23, 2011

§60.640   Applicability and designation of affected facilities.
§60.641   Definitions.
§60.642   Standards for sulfur dioxide.
§60.643   Compliance provisions.
§60.644   Test methods and procedures.
§60.645   [Reserved]
§60.646   Monitoring of emissions and operations.
§60.647   Recordkeeping and reporting requirements.
§60.648   Optional procedure for measuring hydrogen sulfide in acid gas—Tutwiler Procedure.

Subpart MMM [Reserved]

Subpart NNN—Standards of Performance for Volatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation Operations

§60.660   Applicability and designation of affected facility.
§60.661   Definitions.
§60.662   Standards.
§60.663   Monitoring of emissions and operations.
§60.664   Test methods and procedures.
§60.665   Reporting and recordkeeping requirements.
§60.666   Reconstruction.
§60.667   Chemicals affected by subpart NNN.
§60.668   Delegation of authority.

Subpart OOO—Standards of Performance for Nonmetallic Mineral Processing Plants

§60.670   Applicability and designation of affected facility.
§60.671   Definitions.
§60.672   Standard for particulate matter (PM).
§60.673   Reconstruction.
§60.674   Monitoring of operations.
§60.675   Test methods and procedures.
§60.676   Reporting and recordkeeping.
Table 1 to Subpart OOO of Part 60—Exceptions to Applicability of Subpart A to Subpart OOO
Table 2 to Subpart OOO of Part 60—Stack Emission Limits for Affected Facilities With Capture Systems
Table 3 to Subpart OOO of Part 60—Fugitive Emission Limits

Subpart PPP—Standard of Performance for Wool Fiberglass Insulation Manufacturing Plants

§60.680   Applicability and designation of affected facility.
§60.681   Definitions.
§60.682   Standard for particulate matter.
§60.683   Monitoring of operations.
§60.684   Recordkeeping and reporting requirements.
§60.685   Test methods and procedures.

Subpart QQQ—Standards of Performance for VOC Emissions From Petroleum Refinery Wastewater Systems

§60.690   Applicability and designation of affected facility.
§60.691   Definitions.
§60.692-1   Standards: General.
§60.692-2   Standards: Individual drain systems.
§60.692-3   Standards: Oil-water separators.
§60.692-4   Standards: Aggregate facility.
§60.692-5   Standards: Closed vent systems and control devices.
§60.692-6   Standards: Delay of repair.
§60.692-7   Standards: Delay of compliance.
§60.693-1   Alternative standards for individual drain systems.
§60.693-2   Alternative standards for oil-water separators.
§60.694   Permission to use alternative means of emission limitation.
§60.695   Monitoring of operations.
§60.696   Performance test methods and procedures and compliance provisions.
§60.697   Recordkeeping requirements.
§60.698   Reporting requirements.
§60.699   Delegation of authority.

Subpart RRR—Standards of Performance for Volatile Organic Compound Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor Processes

§60.700   Applicability and designation of affected facility.
§60.701   Definitions.
§60.702   Standards.
§60.703   Monitoring of emissions and operations.
§60.704   Test methods and procedures.
§60.705   Reporting and recordkeeping requirements.
§60.706   Reconstruction.
§60.707   Chemicals affected by subpart RRR.
§60.708   Delegation of authority.

Subpart SSS—Standards of Performance for Magnetic Tape Coating Facilities

§60.710   Applicability and designation of affected facility.
§60.711   Definitions, symbols, and cross reference tables.
§60.712   Standards for volatile organic compounds.
§60.713   Compliance provisions.
§60.714   Installation of monitoring devices and recordkeeping.
§60.715   Test methods and procedures.
§60.716   Permission to use alternative means of emission limitation.
§60.717   Reporting and monitoring requirements.
§60.718   Delegation of authority.

Subpart TTT—Standards of Performance for Industrial Surface Coating: Surface Coating of Plastic Parts for Business Machines

§60.720   Applicability and designation of affected facility.
§60.721   Definitions.
§60.722   Standards for volatile organic compounds.
§60.723   Performance tests and compliance provisions.
§60.724   Reporting and recordkeeping requirements.
§60.725   Test methods and procedures.
§60.726   Delegation of authority.

Subpart UUU—Standards of Performance for Calciners and Dryers in Mineral Industries

§60.730   Applicability and designation of affected facility.
§60.731   Definitions.
§60.732   Standards for particulate matter.
§60.733   Reconstruction.
§60.734   Monitoring of emissions and operations.
§60.735   Recordkeeping and reporting requirements.
§60.736   Test methods and procedures.
§60.737   Delegation of authority.

Subpart VVV—Standards of Performance for Polymeric Coating of Supporting Substrates Facilities

§60.740   Applicability and designation of affected facility.
§60.741   Definitions, symbols, and cross-reference tables.
§60.742   Standards for volatile organic compounds.
§60.743   Compliance provisions.
§60.744   Monitoring requirements.
§60.745   Test methods and procedures.
§60.746   Permission to use alternative means of emission limitation.
§60.747   Reporting and recordkeeping requirements.
§60.748   Delegation of authority.

Subpart WWW—Standards of Performance for Municipal Solid Waste Landfills

§60.750   Applicability, designation of affected facility, and delegation of authority.
§60.751   Definitions.
§60.752   Standards for air emissions from municipal solid waste landfills.
§60.753   Operational standards for collection and control systems.
§60.754   Test methods and procedures.
§60.755   Compliance provisions.
§60.756   Monitoring of operations.
§60.757   Reporting requirements.
§60.758   Recordkeeping requirements.
§60.759   Specifications for active collection systems.

Subpart AAAA—Standards of Performance for Small Municipal Waste Combustion Units for Which Construction is Commenced After August 30, 1999 or for Which Modification or Reconstruction is Commenced After June 6, 2001

Introduction

§60.1000   What does this subpart do?
§60.1005   When does this subpart become effective?

Applicability

§60.1010   Does this subpart apply to my municipal waste combustion unit?
§60.1015   What is a new municipal waste combustion unit?
§60.1020   Does this subpart allow any exemptions?
§60.1025   Do subpart E new source performance standards also apply to my municipal waste combustion unit?
§60.1030   Can the Administrator delegate authority to enforce these Federal new source performance standards to a State agency?
§60.1035   How are these new source performance standards structured?
§60.1040   Do all five components of these new source performance standards apply at the same time?
§60.1045   Are there different subcategories of small municipal waste combustion units within this subpart?

Preconstruction Requirements: Materials Separation Plan

§60.1050   Who must submit a materials separation plan?
§60.1055   What is a materials separation plan?
§60.1060   What steps must I complete for my materials separation plan?
§60.1065   What must I include in my draft materials separation plan?
§60.1070   How do I make my draft materials separation plan available to the public?
§60.1075   When must I accept comments on the materials separation plan?
§60.1080   Where and when must I hold a public meeting on my draft materials separation plan?
§60.1085   What must I do with any public comments I receive during the public comment period on my draft materials separation plan?
§60.1090   What must I do with my revised materials separation plan?
§60.1095   What must I include in the public meeting on my revised materials separation plan?
§60.1100   What must I do with any public comments I receive on my revised materials separation plan?
§60.1105   How do I submit my final materials separation plan?

Preconstruction Requirements: Siting Analysis

§60.1110   Who must submit a siting analysis?
§60.1115   What is a siting analysis?
§60.1120   What steps must I complete for my siting analysis?
§60.1125   What must I include in my siting analysis?
§60.1130   How do I make my siting analysis available to the public?
§60.1135   When must I accept comments on the siting analysis and revised materials separation plan?
§60.1140   Where and when must I hold a public meeting on the siting analysis?
§60.1145   What must I do with any public comments I receive during the public comment period on my siting analysis?
§60.1150   How do I submit my siting analysis?

Good Combustion Practices: Operator Training

§60.1155   What types of training must I do?
§60.1160   Who must complete the operator training course? By when?
§60.1165   Who must complete the plant-specific training course?
§60.1170   What plant-specific training must I provide?
§60.1175   What information must I include in the plant-specific operating manual?
§60.1180   Where must I keep the plant-specific operating manual?

Good Combustion Practices: Operator Certification

§60.1185   What types of operator certification must the chief facility operator and shift supervisor obtain and by when must they obtain it?
§60.1190   After the required date for operator certification, who may operate the municipal waste combustion unit?
§60.1195   What if all the certified operators must be temporarily offsite?

Good Combustion Practices: Operating Requirements

§60.1200   What are the operating practice requirements for my municipal waste combustion unit?
§60.1205   What happens to the operating requirements during periods of startup, shutdown, and malfunction?

Emission Limits

§60.1210   What pollutants are regulated by this subpart?
§60.1215   What emission limits must I meet? By when?
§60.1220   What happens to the emission limits during periods of startup, shutdown, and malfunction?

Continuous Emission Monitoring

§60.1225   What types of continuous emission monitoring must I perform?
§60.1230   What continuous emission monitoring systems must I install for gaseous pollutants?
§60.1235   How are the data from the continuous emission monitoring systems used?
§60.1240   How do I make sure my continuous emission monitoring systems are operating correctly?
§60.1245   Am I exempt from any appendix B or appendix F requirements to evaluate continuous emission monitoring systems?
§60.1250   What is my schedule for evaluating continuous emission monitoring systems?
§60.1255   What must I do if I choose to monitor carbon dioxide instead of oxygen as a diluent gas?
§60.1260   What is the minimum amount of monitoring data I must collect with my continuous emission monitoring systems and is the data collection requirement enforceable?
§60.1265   How do I convert my 1-hour arithmetic averages into the appropriate averaging times and units?
§60.1270   What is required for my continuous opacity monitoring system and how are the data used?
§60.1275   What additional requirements must I meet for the operation of my continuous emission monitoring systems and continuous opacity monitoring system?
§60.1280   What must I do if any of my continuous emission monitoring systems are temporarily unavailable to meet the data collection requirements?

Stack Testing

§60.1285   What types of stack tests must I conduct?
§60.1290   How are the stack test data used?
§60.1295   What schedule must I follow for the stack testing?
§60.1300   What test methods must I use to stack test?
§60.1305   May I conduct stack testing less often?
§60.1310   May I deviate from the 13-month testing schedule if unforeseen circumstances arise?

Other Monitoring Requirements

§60.1315   Must I meet other requirements for continuous monitoring?
§60.1320   How do I monitor the load of my municipal waste combustion unit?
§60.1325   How do I monitor the temperature of flue gases at the inlet of my particulate matter control device?
§60.1330   How do I monitor the injection rate of activated carbon?
§60.1335   What is the minimum amount of monitoring data I must collect with my continuous parameter monitoring systems and is the data collection requirement enforceable?

Recordkeeping

§60.1340   What records must I keep?
§60.1345   Where must I keep my records and for how long?
§60.1350   What records must I keep for the materials separation plan and siting analysis?
§60.1355   What records must I keep for operator training and certification?
§60.1360   What records must I keep for stack tests?
§60.1365   What records must I keep for continuously monitored pollutants or parameters?
§60.1370   What records must I keep for municipal waste combustion units that use activated carbon?

Reporting

§60.1375   What reports must I submit before I submit my notice of construction?
§60.1380   What must I include in my notice of construction?
§60.1385   What reports must I submit after I submit my notice of construction and in what form?
§60.1390   What are the appropriate units of measurement for reporting my data?
§60.1395   When must I submit the initial report?
§60.1400   What must I include in my initial report?
§60.1405   When must I submit the annual report?
§60.1410   What must I include in my annual report?
§60.1415   What must I do if I am out of compliance with the requirements of this subpart?
§60.1420   If a semiannual report is required, when must I submit it?
§60.1425   What must I include in the semiannual out-of-compliance reports?
§60.1430   Can reporting dates be changed?

Air Curtain Incinerators that Burn 100 Percent Yard Waste

§60.1435   What is an air curtain incinerator?
§60.1440   What is yard waste?
§60.1445   What are the emission limits for air curtain incinerators that burn 100 percent yard waste?
§60.1450   How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?
§60.1455   What are the recordkeeping and reporting requirements for air curtain incinerators that burn 100 percent yard waste?

Equations

§60.1460   What equations must I use?

Definitions

§60.1465   What definitions must I know?
Table 1 to Subpart AAAA of Part 60—Emission Limits for New Small Municipal Waste Combustion Units
Table 2 to Subpart AAAA of Part 60—Carbon Monoxide Emission Limits for New Small Municipal Waste Combustion Units
Table 3 of Subpart AAAA of Part 60—Requirements for Validating Continuous Emission Monitoring Systems (CEMS)
Table 4 of Subpart AAAA of Part 60—Requirements for Continuous Emission Monitoring Systems (CEMS)
Table 5 of Subpart AAAA of Part 60—Requirements for Stack Tests

Subpart BBBB—Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999

Introduction

§60.1500   What is the purpose of this subpart?
§60.1505   Am I affected by this subpart?
§60.1510   Is a State plan required for all States?
§60.1515   What must I include in my State plan?
§60.1520   Is there an approval process for my State plan?
§60.1525   What if my State plan is not approvable?
§60.1530   Is there an approval process for a negative declaration letter?
§60.1535   What compliance schedule must I include in my State plan?
§60.1540   Are there any State plan requirements for this subpart that supersede the requirements specified in subpart B?
§60.1545   Does this subpart directly affect municipal waste combustion unit owners and operators in my State?

Applicability of State Plans

§60.1550   What municipal waste combustion units must I address in my State plan?
§60.1555   Are any small municipal waste combustion units exempt from my State plan?
§60.1560   Can an affected municipal waste combustion unit reduce its capacity to less than 35 tons per day rather than comply with my State plan?
§60.1565   What subcategories of small municipal waste combustion units must I include in my State plan?

Use of Model Rule

§60.1570   What is the “model rule” in this subpart?
§60.1575   How does the model rule relate to the required elements of my State plan?
§60.1580   What are the principal components of the model rule?

Model Rule—Increments of Progress

§60.1585   What are my requirements for meeting increments of progress and achieving final compliance?
§60.1590   When must I complete each increment of progress?
§60.1595   What must I include in the notifications of achievement of my increments of progress?
§60.1600   When must I submit the notifications of achievement of increments of progress?
§60.1605   What if I do not meet an increment of progress?
§60.1610   How do I comply with the increment of progress for submittal of a control plan?
§60.1615   How do I comply with the increment of progress for awarding contracts?
§60.1620   How do I comply with the increment of progress for initiating onsite construction?
§60.1625   How do I comply with the increment of progress for completing onsite construction?
§60.1630   How do I comply with the increment of progress for achieving final compliance?
§60.1635   What must I do if I close my municipal waste combustion unit and then restart my municipal waste combustion unit?
§60.1640   What must I do if I plan to permanently close my municipal waste combustion unit and not restart it?

Model Rule—Good Combustion Practices: Operator Training

§60.1645   What types of training must I do?
§60.1650   Who must complete the operator training course? By when?
§60.1655   Who must complete the plant-specific training course?
§60.1660   What plant-specific training must I provide?
§60.1665   What information must I include in the plant-specific operating manual?
§60.1670   Where must I keep the plant-specific operating manual?

Model Rule—Good Combustion Practices: Operator Certification

§60.1675   What types of operator certification must the chief facility operator and shift supervisor obtain and by when must they obtain it?
§60.1680   After the required date for operator certification, who may operate the municipal waste combustion unit?
§60.1685   What if all the certified operators must be temporarily offsite?

Model Rule—Good Combustion Practices: Operating Requirements

§60.1690   What are the operating practice requirements for my municipal waste combustion unit?
§60.1695   What happens to the operating requirements during periods of startup, shutdown, and malfunction?

Model Rule—Emission Limits

§60.1700   What pollutants are regulated by this subpart?
§60.1705   What emission limits must I meet? By when?
§60.1710   What happens to the emission limits during periods of startup, shutdown, and malfunction?

Model Rule—Continuous Emission Monitoring

§60.1715   What types of continuous emission monitoring must I perform?
§60.1720   What continuous emission monitoring systems must I install for gaseous pollutants?
§60.1725   How are the data from the continuous emission monitoring systems used?
§60.1730   How do I make sure my continuous emission monitoring systems are operating correctly?
§60.1735   Am I exempt from any appendix B or appendix F requirements to evaluate continuous emission monitoring systems?
§60.1740   What is my schedule for evaluating continuous emission monitoring systems?
§60.1745   What must I do if I choose to monitor carbon dioxide instead of oxygen as a diluent gas?
§60.1750   What is the minimum amount of monitoring data I must collect with my continuous emission monitoring systems and is the data collection requirement enforceable?
§60.1755   How do I convert my 1-hour arithmetic averages into appropriate averaging times and units?
§60.1760   What is required for my continuous opacity monitoring system and how are the data used?
§60.1765   What additional requirements must I meet for the operation of my continuous emission monitoring systems and continuous opacity monitoring system?
§60.1770   What must I do if any of my continuous emission monitoring systems are temporarily unavailable to meet the data collection requirements?

Model Rule—Stack Testing

§60.1775   What types of stack tests must I conduct?
§60.1780   How are the stack test data used?
§60.1785   What schedule must I follow for the stack testing?
§60.1790   What test methods must I use to stack test?
§60.1795   May I conduct stack testing less often?
§60.1800   May I deviate from the 13-month testing schedule if unforeseen circumstances arise?

Model Rule—Other Monitoring Requirements

§60.1805   Must I meet other requirements for continuous monitoring?
§60.1810   How do I monitor the load of my municipal waste combustion unit?
§60.1815   How do I monitor the temperature of flue gases at the inlet of my particulate matter control device?
§60.1820   How do I monitor the injection rate of activated carbon?
§60.1825   What is the minimum amount of monitoring data I must collect with my continuous parameter monitoring systems and is the data collection requirement enforceable?

Model Rule—Recordkeeping

§60.1830   What records must I keep?
§60.1835   Where must I keep my records and for how long?
§60.1840   What records must I keep for operator training and certification?
§60.1845   What records must I keep for stack tests?
§60.1850   What records must I keep for continuously monitored pollutants or parameters?
§60.1855   What records must I keep for municipal waste combustion units that use activated carbon?

Model Rule—Reporting

§60.1860   What reports must I submit and in what form?
§60.1865   What are the appropriate units of measurement for reporting my data?
§60.1870   When must I submit the initial report?
§60.1875   What must I include in my initial report?
§60.1880   When must I submit the annual report?
§60.1885   What must I include in my annual report?
§60.1890   What must I do if I am out of compliance with the requirements of this subpart?
§60.1895   If a semiannual report is required, when must I submit it?
§60.1900   What must I include in the semiannual out-of-compliance reports?
§60.1905   Can reporting dates be changed?

Model Rule—Air Curtain Incinerators That Burn 100 Percent Yard Waste

§60.1910   What is an air curtain incinerator?
§60.1915   What is yard waste?
§60.1920   What are the emission limits for air curtain incinerators that burn 100 percent yard waste?
§60.1925   How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?
§60.1930   What are the recordkeeping and reporting requirements for air curtain incinerators that burn 100 percent yard waste?

Equations

§60.1935   What equations must I use?

Definitions

§60.1940   What definitions must I know?
Table 1 to Subpart BBBB of Part 60—Model Rule—Compliance Schedules and Increments of Progress
Table 2 to Subpart BBBB of Part 60—Model Rule—Class I Emission Limits for Existing Small Municipal Waste Combustion Units
Table 3 to Subpart BBBB of Part 60—Model Rule—Class I Nitrogen Oxides Emission Limits for Existing Small Municipal Waste Combustion Units
Table 4 to Subpart BBBB of Part 60—Model Rule—Class II Emission Limits for Existing Small Municipal Waste Combustion Unit
Table 5 to Subpart BBBB of Part 60—Model Rule—Carbon Monoxide Emission Limits for Existing Small Municipal Waste Combustion Units
Table 6 to Subpart BBBB of Part 60—Model Rule—Requirements for Validating Continuous Emission Monitoring Systems (CEMS)
Table 7 to Subpart BBBB of Part 60—Model Rule—Requirements for Continuous Emission Monitoring Systems (CEMS)
Table 8 to Subpart BBBB of Part 60—Model Rule—Requirements for Stack Tests

Subpart CCCC—Standards of Performance for Commercial and Industrial Solid Waste Incineration Units

Introduction

§60.2000   What does this subpart do?
§60.2005   When does this subpart become effective?

Applicability

§60.2010   Does this subpart apply to my incineration unit?
§60.2015   What is a new incineration unit?
§60.2020   What combustion units are exempt from this subpart?
§60.2030   Who implements and enforces this subpart?
§60.2035   How are these new source performance standards structured?
§60.2040   Do all eleven components of these new source performance standards apply at the same time?

Preconstruction Siting Analysis

§60.2045   Who must prepare a siting analysis?
§60.2050   What is a siting analysis?

Waste Management Plan

§60.2055   What is a waste management plan?
§60.2060   When must I submit my waste management plan?
§60.2065   What should I include in my waste management plan?

Operator Training and Qualification

§60.2070   What are the operator training and qualification requirements?
§60.2075   When must the operator training course be completed?
§60.2080   How do I obtain my operator qualification?
§60.2085   How do I maintain my operator qualification?
§60.2090   How do I renew my lapsed operator qualification?
§60.2095   What site-specific documentation is required?
§60.2100   What if all the qualified operators are temporarily not accessible?

Emission Limitations and Operating Limits

§60.2105   What emission limitations must I meet and by when?
§60.2110   What operating limits must I meet and by when?
§60.2115   What if I do not use a wet scrubber, fabric filter, activated carbon injection, selective noncatalytic reduction, an electrostatic precipitator, or a dry scrubber to comply with the emission limitations?
§60.2120   Affirmative defense for violation of emission standards during malfunction.

Performance Testing

§60.2125   How do I conduct the initial and annual performance test?
§60.2130   How are the performance test data used?

Initial Compliance Requirements

§60.2135   How do I demonstrate initial compliance with the emission limitations and establish the operating limits?
§60.2140   By what date must I conduct the initial performance test?
§60.2141   By what date must I conduct the initial air pollution control device inspection?

Continuous Compliance Requirements

§60.2145   How do I demonstrate continuous compliance with the emission limitations and the operating limits?
§60.2150   By what date must I conduct the annual performance test?
§60.2151   By what date must I conduct the annual air pollution control device inspection?
§60.2155   May I conduct performance testing less often?
§60.2160   May I conduct a repeat performance test to establish new operating limits?

Monitoring

§60.2165   What monitoring equipment must I install and what parameters must I monitor?
§60.2170   Is there a minimum amount of monitoring data I must obtain?

Recordkeeping and Reporting

§60.2175   What records must I keep?
§60.2180   Where and in what format must I keep my records?
§60.2185   What reports must I submit?
§60.2190   What must I submit prior to commencing construction?
§60.2195   What information must I submit prior to initial startup?
§60.2200   What information must I submit following my initial performance test?
§60.2205   When must I submit my annual report?
§60.2210   What information must I include in my annual report?
§60.2215   What else must I report if I have a deviation from the operating limits or the emission limitations?
§60.2220   What must I include in the deviation report?
§60.2225   What else must I report if I have a deviation from the requirement to have a qualified operator accessible?
§60.2230   Are there any other notifications or reports that I must submit?
§60.2235   In what form can I submit my reports?
§60.2240   Can reporting dates be changed?

Title V Operating Permits

§60.2242   Am I required to apply for and obtain a Title V operating permit for my unit?

Air Curtain Incinerators

§60.2245   What is an air curtain incinerator?
§60.2250   What are the emission limitations for air curtain incinerators?
§60.2255   How must I monitor opacity for air curtain incinerators?
§60.2260   What are the recordkeeping and reporting requirements for air curtain incinerators?

Definitions

§60.2265   What definitions must I know?
Table 1 to Subpart CCCC of Part 60—Emission Limitations for CISWI Units for Which Construction is Commenced After November 30, 1999, But no Later Than June 4, 2010, or for Which Modification or Reconstruction is Commenced on or After June 1, 2001, But no Later Than August 7, 2013
Table 2 to Subpart CCCC of Part 60—Operating Limits for Wet Scrubbers
Table 3 to Subpart CCCC of Part 60—Toxic Equivalency Factors
Table 4 to Subpart CCCC of Part 60—Summary of Reporting Requirements
Table 5 to Subpart CCCC of Part 60—Emission Limitations for Incinerators That Commenced Construction After June 4, 2010, or That Commenced Reconstruction or Modification After August 7, 2013
Table 6 to Subpart CCCC of Part 60—Emission Limitations for Energy Recovery Units That Commenced Construction After June 4, 2010, or That Commenced Reconstruction or Modification After August 7, 2013
Table 7 to Subpart CCCC of Part 60—Emission Limitations for Waste-burning Kilns That Commenced Construction After June 4, 2010, or Reconstruction or Modification After August 7, 2013
Table 8 to Subpart CCCC of Part 60—Emission Limitations for Small, Remote Incinerators That Commenced Construction After June 4, 2010, Or That Commenced Reconstruction or Modification After August 7, 2013

Subpart DDDD—Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units

Introduction

§60.2500   What is the purpose of this subpart?
§60.2505   Am I affected by this subpart?
§60.2510   Is a State plan required for all States?
§60.2515   What must I include in my State plan?
§60.2520   Is there an approval process for my State plan?
§60.2525   What if my state plan is not approvable?
§60.2530   Is there an approval process for a negative declaration letter?
§60.2535   What compliance schedule must I include in my State plan?
§60.2540   Are there any State plan requirements for this subpart that apply instead of the requirements specified in subpart B?
§60.2541   In lieu of a state plan submittal, are there other acceptable option(s) for a state to meet its Clean Air Act section 111(d)/129(b)(2) obligations?
§60.2542   What authorities will not be delegated to state, local, or tribal agencies?
§60.2545   Does this subpart directly affect CISWI unit owners and operators in my State?

Applicability of State Plans

§60.2550   What CISWI units must I address in my State plan?
§60.2555   What combustion units are exempt from my State plan?

Use of Model Rule

§60.2560   What is the “model rule” in this subpart?
§60.2565   How does the model rule relate to the required elements of my State plan?
§60.2570   What are the principal components of the model rule?

Model Rule—Increments of Progress

§60.2575   What are my requirements for meeting increments of progress and achieving final compliance?
§60.2580   When must I complete each increment of progress?
§60.2585   What must I include in the notifications of achievement of increments of progress?
§60.2590   When must I submit the notifications of achievement of increments of progress?
§60.2595   What if I do not meet an increment of progress?
§60.2600   How do I comply with the increment of progress for submittal of a control plan?
§60.2605   How do I comply with the increment of progress for achieving final compliance?
§60.2610   What must I do if I close my CISWI unit and then restart it?
§60.2615   What must I do if I plan to permanently close my CISWI unit and not restart it?

Model Rule—Waste Management Plan

§60.2620   What is a waste management plan?
§60.2625   When must I submit my waste management plan?
§60.2630   What should I include in my waste management plan?

Model Rule—Operator Training and Qualification

§60.2635   What are the operator training and qualification requirements?
§60.2640   When must the operator training course be completed?
§60.2645   How do I obtain my operator qualification?
§60.2650   How do I maintain my operator qualification?
§60.2655   How do I renew my lapsed operator qualification?
§60.2660   What site-specific documentation is required?
§60.2665   What if all the qualified operators are temporarily not accessible?

Model Rule—Emission Limitations and Operating Limits

§60.2670   What emission limitations must I meet and by when?
§60.2675   What operating limits must I meet and by when?
§60.2680   What if I do not use a wet scrubber, fabric filter, activated carbon injection, selective noncatalytic reduction, an electrostatic precipitator, or a dry scrubber to comply with the emission limitations?
§60.2685   Affirmative defense for violation of emission standards during malfunction.

Model Rule—Performance Testing

§60.2690   How do I conduct the initial and annual performance test?
§60.2695   How are the performance test data used?

Model Rule—Initial Compliance Requirements

§60.2700   How do I demonstrate initial compliance with the amended emission limitations and establish the operating limits?
§60.2705   By what date must I conduct the initial performance test?
§60.2706   By what date must I conduct the initial air pollution control device inspection?

Model Rule—Continuous Compliance Requirements

§60.2710   How do I demonstrate continuous compliance with the amended emission limitations and the operating limits?
§60.2715   By what date must I conduct the annual performance test?
§60.2716   By what date must I conduct the annual air pollution control device inspection?
§60.2720   May I conduct performance testing less often?
§60.2725   May I conduct a repeat performance test to establish new operating limits?

Model Rule—Monitoring

§60.2730   What monitoring equipment must I install and what parameters must I monitor?
§60.2735   Is there a minimum amount of monitoring data I must obtain?

Model Rule—Recordkeeping and Reporting

§60.2740   What records must I keep?
§60.2745   Where and in what format must I keep my records?
§60.2750   What reports must I submit?
§60.2755   When must I submit my waste management plan?
§60.2760   What information must I submit following my initial performance test?
§60.2765   When must I submit my annual report?
§60.2770   What information must I include in my annual report?
§60.2775   What else must I report if I have a deviation from the operating limits or the emission limitations?
§60.2780   What must I include in the deviation report?
§60.2785   What else must I report if I have a deviation from the requirement to have a qualified operator accessible?
§60.2790   Are there any other notifications or reports that I must submit?
§60.2795   In what form can I submit my reports?
§60.2800   Can reporting dates be changed?

Model Rule—Title V Operating Permits

§60.2805   Am I required to apply for and obtain a Title V operating permit for my unit?

Model Rule—Air Curtain Incinerators

§60.2810   What is an air curtain incinerator?
§60.2815   What are my requirements for meeting increments of progress and achieving final compliance?
§60.2820   When must I complete each increment of progress?
§60.2825   What must I include in the notifications of achievement of increments of progress?
§60.2830   When must I submit the notifications of achievement of increments of progress?
§60.2835   What if I do not meet an increment of progress?
§60.2840   How do I comply with the increment of progress for submittal of a control plan?
§60.2845   How do I comply with the increment of progress for achieving final compliance?
§60.2850   What must I do if I close my air curtain incinerator and then restart it?
§60.2855   What must I do if I plan to permanently close my air curtain incinerator and not restart it?
§60.2860   What are the emission limitations for air curtain incinerators?
§60.2865   How must I monitor opacity for air curtain incinerators?
§60.2870   What are the recordkeeping and reporting requirements for air curtain incinerators?

Model Rule—Definitions

§60.2875   What definitions must I know?
Table 1 to Subpart DDDD of Part 60—Model Rule—Increments of Progress and Compliance Schedules
Table 2 to Subpart DDDD of Part 60—Model Rule—Emission Limitations That Apply to Incinerators Before [Date to be specified in state plan]
Table 3 to Subpart DDDD of Part 60—Model Rule—Operating Limits for Wet Scrubbers
Table 4 to Subpart DDDD of Part 60—Model Rule—Toxic Equivalency Factors
Table 5 to Subpart DDDD of Part 60—Model Rule—Summary of Reporting Requirements
Table 6 to Subpart DDDD of Part 60—Model Rule—Emission Limitations That Apply to Incinerators on and After [Date to be specified in state plan]
Table 7 to Subpart DDDD of Part 60—Model Rule—Emission Limitations That Apply to Energy Recovery Units After May 20, 2011
Table 8 to Subpart DDDD of Part 60—Model Rule—Emission Limitations That Apply to Waste-Burning Kilns After May 20, 2011
Table 9 to Subpart DDDD of Part 60—Model Rule—Emission Limitations That Apply to Small, Remote Incinerators After May 20, 2011

Subpart EEEE—Standards of Performance for Other Solid Waste Incineration Units for Which Construction is Commenced After December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006

Introduction

§60.2880   What does this subpart do?
§60.2881   When does this subpart become effective?

Applicability

§60.2885   Does this subpart apply to my incineration unit?
§60.2886   What is a new incineration unit?
§60.2887   What combustion units are excluded from this subpart?
§60.2888   Are air curtain incinerators regulated under this subpart?
§60.2889   Who implements and enforces this subpart?
§60.2890   How are these new source performance standards structured?
§60.2891   Do all components of these new source performance standards apply at the same time?

Preconstruction Siting Analysis

§60.2894   Who must prepare a siting analysis?
§60.2895   What is a siting analysis?

Waste Management Plan

§60.2899   What is a waste management plan?
§60.2900   When must I submit my waste management plan?
§60.2901   What should I include in my waste management plan?

Operator Training and Qualification

§60.2905   What are the operator training and qualification requirements?
§60.2906   When must the operator training course be completed?
§60.2907   How do I obtain my operator qualification?
§60.2908   How do I maintain my operator qualification?
§60.2909   How do I renew my lapsed operator qualification?
§60.2910   What site-specific documentation is required?
§60.2911   What if all the qualified operators are temporarily not accessible?

Emission Limitations and Operating Limits

§60.2915   What emission limitations must I meet and by when?
§60.2916   What operating limits must I meet and by when?
§60.2917   What if I do not use a wet scrubber to comply with the emission limitations?
§60.2918   What happens during periods of startup, shutdown, and malfunction?

Performance Testing

§60.2922   How do I conduct the initial and annual performance test?
§60.2923   How are the performance test data used?

Initial Compliance Requirements

§60.2927   How do I demonstrate initial compliance with the emission limitations and establish the operating limits?
§60.2928   By what date must I conduct the initial performance test?

Continuous Compliance Requirements

§60.2932   How do I demonstrate continuous compliance with the emission limitations and the operating limits?
§60.2933   By what date must I conduct the annual performance test?
§60.2934   May I conduct performance testing less often?
§60.2935   May I conduct a repeat performance test to establish new operating limits?

Monitoring

§60.2939   What continuous emission monitoring systems must I install?
§60.2940   How do I make sure my continuous emission monitoring systems are operating correctly?
§60.2941   What is my schedule for evaluating continuous emission monitoring systems?
§60.2942   What is the minimum amount of monitoring data I must collect with my continuous emission monitoring systems, and is the data collection requirement enforceable?
§60.2943   How do I convert my 1-hour arithmetic averages into the appropriate averaging times and units?
§60.2944   What operating parameter monitoring equipment must I install, and what operating parameters must I monitor?
§60.2945   Is there a minimum amount of operating parameter monitoring data I must obtain?

Recordkeeping and Reporting

§60.2949   What records must I keep?
§60.2950   Where and in what format must I keep my records?
§60.2951   What reports must I submit?
§60.2952   What must I submit prior to commencing construction?
§60.2953   What information must I submit prior to initial startup?
§60.2954   What information must I submit following my initial performance test?
§60.2955   When must I submit my annual report?
§60.2956   What information must I include in my annual report?
§60.2957   What else must I report if I have a deviation from the operating limits or the emission limitations?
§60.2958   What must I include in the deviation report?
§60.2959   What else must I report if I have a deviation from the requirement to have a qualified operator accessible?
§60.2960   Are there any other notifications or reports that I must submit?
§60.2961   In what form can I submit my reports?
§60.2962   Can reporting dates be changed?

Title V Operating Permits

§60.2966   Am I required to apply for and obtain a title V operating permit for my unit?
§60.2967   When must I submit a title V permit application for my new unit?

Temporary-Use Incinerators and Air Curtain Incinerators Used in Disaster Recovery

§60.2969   What are the requirements for temporary-use incinerators and air curtain incinerators used in disaster recovery?

Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste

§60.2970   What is an air curtain incinerator?
§60.2971   What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste?
§60.2972   How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste?
§60.2973   What are the recordkeeping and reporting requirements for air curtain incinerators that burn only wood waste, clean lumber, and yard waste?
§60.2974   Am I required to apply for and obtain a title V operating permit for my air curtain incinerator that burns only wood waste, clean lumber, and yard waste?

Equations

§60.2975   What equations must I use?

Definitions

§60.2977   What definitions must I know?
Table 1 to Subpart EEEE of Part 60—Emission Limitations
Table 2 to Subpart EEEE of Part 60—Operating Limits for Incinerators and Wet Scrubbers
Table 3 to Subpart EEEE of Part 60—Requirements for Continuous Emission Monitoring Systems (CEMS)
Table 4 to Subpart EEEE of Part 60—Summary of Reporting Requirements

Subpart FFFF—Emission Guidelines and Compliance Times for Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004

Introduction

§60.2980   What is the purpose of this subpart?
§60.2981   Am I affected by this subpart?
§60.2982   Is a State plan required for all States?
§60.2983   What must I include in my State plan?
§60.2984   Is there an approval process for my State plan?
§60.2985   What if my State plan is not approvable?
§60.2986   Is there an approval process for a negative declaration letter?
§60.2987   What compliance schedule must I include in my State plan?
§60.2988   Are there any State plan requirements for this subpart that apply instead of the requirements specified in subpart B of this part?
§60.2989   Does this subpart directly affect incineration unit owners and operators in my State?
§60.2990   What Authorities are withheld by EPA?

Applicability of State Plans

§60.2991   What incineration units must I address in my State plan?
§60.2992   What is an existing incineration unit?
§60.2993   Are any combustion units excluded from my State plan?
§60.2994   Are air curtain incinerators regulated under this subpart?

Model Rule—Use of Model Rule

§60.2996   What is the purpose of the “model rule” in this subpart?
§60.2997   How does the model rule relate to the required elements of my State plan?
§60.2998   What are the principal components of the model rule?

Model Rule—Compliance Schedule

§60.3000   When must I comply?
§60.3001   What must I do if I close my OSWI unit and then restart it?
§60.3002   What must I do if I plan to permanently close my OSWI unit and not restart it?

Model Rule—Waste Management Plan

§60.3010   What is a waste management plan?
§60.3011   When must I submit my waste management plan?
§60.3012   What should I include in my waste management plan?

Model Rule—Operator Training and Qualification

§60.3014   What are the operator training and qualification requirements?
§60.3015   When must the operator training course be completed?
§60.3016   How do I obtain my operator qualification?
§60.3017   How do I maintain my operator qualification?
§60.3018   How do I renew my lapsed operator qualification?
§60.3019   What site-specific documentation is required?
§60.3020   What if all the qualified operators are temporarily not accessible?

Model Rule—Emission Limitations and Operating Limits

§60.3022   What emission limitations must I meet and by when?
§60.3023   What operating limits must I meet and by when?
§60.3024   What if I do not use a wet scrubber to comply with the emission limitations?
§60.3025   What happens during periods of startup, shutdown, and malfunction?

Model Rule—Performance Testing

§60.3027   How do I conduct the initial and annual performance test?
§60.3028   How are the performance test data used?

Model Rule—Initial Compliance Requirements

§60.3030   How do I demonstrate initial compliance with the emission limitations and establish the operating limits?
§60.3031   By what date must I conduct the initial performance test?

Model Rule—Continuous Compliance Requirements

§60.3033   How do I demonstrate continuous compliance with the emission limitations and the operating limits?
§60.3034   By what date must I conduct the annual performance test?
§60.3035   May I conduct performance testing less often?
§60.3036   May I conduct a repeat performance test to establish new operating limits?

Model Rule—Monitoring

§60.3038   What continuous emission monitoring systems must I install?
§60.3039   How do I make sure my continuous emission monitoring systems are operating correctly?
§60.3040   What is my schedule for evaluating continuous emission monitoring systems?
§60.3041   What is the minimum amount of monitoring data I must collect with my continuous emission monitoring systems, and is the data collection requirement enforceable?
§60.3042   How do I convert my 1-hour arithmetic averages into the appropriate averaging times and units?
§60.3043   What operating parameter monitoring equipment must I install, and what operating parameters must I monitor?
§60.3044   Is there a minimum amount of operating parameter monitoring data I must obtain?

Model Rule—Recordkeeping and Reporting

§60.3046   What records must I keep?
§60.3047   Where and in what format must I keep my records?
§60.3048   What reports must I submit?
§60.3049   What information must I submit following my initial performance test?
§60.3050   When must I submit my annual report?
§60.3051   What information must I include in my annual report?
§60.3052   What else must I report if I have a deviation from the operating limits or the emission limitations?
§60.3053   What must I include in the deviation report?
§60.3054   What else must I report if I have a deviation from the requirement to have a qualified operator accessible?
§60.3055   Are there any other notifications or reports that I must submit?
§60.3056   In what form can I submit my reports?
§60.3057   Can reporting dates be changed?

Model Rule—Title V Operating Permits

§60.3059   Am I required to apply for and obtain a title V operating permit for my unit?
§60.3060   When must I submit a title V permit application for my existing unit?

Model Rule—Temporary-Use Incinerators and Air Curtain Incinerators Used in Disaster Recovery

§60.3061   What are the requirements for temporary-use incinerators and air curtain incinerators used in disaster recovery?

Model Rule—Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste

§60.3062   What is an air curtain incinerator?
§60.3063   When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard waste?
§60.3064   What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber, and yard waste and then restart it?
§60.3065   What must I do if I plan to permanently close my air curtain incinerator that burns only wood waste, clean lumber, and yard waste and not restart it?
§60.3066   What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste?
§60.3067   How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste?
§60.3068   What are the recordkeeping and reporting requirements for air curtain incinerators that burn only wood waste, clean lumber, and yard waste?
§60.3069   Am I required to apply for and obtain a title V operating permit for my air curtain incinerator that burns only wood waste, clean lumber, and yard waste?

Model Rule—Equations

§60.3076   What equations must I use?

Model Rule—Definitions

§60.3078   What definitions must I know?
Table 1 to Subpart FFFF of Part 60—Model Rule—Compliance Schedule
Table 2 to Subpart FFFF of Part 60—Model Rule—Emission Limitations
Table 3 to Subpart FFFF of Part 60—Model Rule—Operating Limits for Incinerators and Wet Scrubbers
Table 4 to Subpart FFFF of Part 60—Model Rule—Requirements for Continuous Emission Monitoring Systems (CEMS)
Table 5 to Subpart FFFF of Part 60—Model Rule—Summary of Reporting Requirements

Subparts GGGG-HHHH [Reserved]

Subpart IIII—Standards of Performance for Stationary Compression Ignition Internal Combustion Engines

What This Subpart Covers

§60.4200   Am I subject to this subpart?

Emission Standards for Manufacturers

§60.4201   What emission standards must I meet for non-emergency engines if I am a stationary CI internal combustion engine manufacturer?
§60.4202   What emission standards must I meet for emergency engines if I am a stationary CI internal combustion engine manufacturer?
§60.4203   How long must my engines meet the emission standards if I am a manufacturer of stationary CI internal combustion engines?

Emission Standards for Owners and Operators

§60.4204   What emission standards must I meet for non-emergency engines if I am an owner or operator of a stationary CI internal combustion engine?
§60.4205   What emission standards must I meet for emergency engines if I am an owner or operator of a stationary CI internal combustion engine?
§60.4206   How long must I meet the emission standards if I am an owner or operator of a stationary CI internal combustion engine?

Fuel Requirements for Owners and Operators

§60.4207   What fuel requirements must I meet if I am an owner or operator of a stationary CI internal combustion engine subject to this subpart?

Other Requirements for Owners and Operators

§60.4208   What is the deadline for importing or installing stationary CI ICE produced in previous model years?
§60.4209   What are the monitoring requirements if I am an owner or operator of a stationary CI internal combustion engine?

Compliance Requirements

§60.4210   What are my compliance requirements if I am a stationary CI internal combustion engine manufacturer?
§60.4211   What are my compliance requirements if I am an owner or operator of a stationary CI internal combustion engine?

Testing Requirements for Owners and Operators

§60.4212   What test methods and other procedures must I use if I am an owner or operator of a stationary CI internal combustion engine with a displacement of less than 30 liters per cylinder?
§60.4213   What test methods and other procedures must I use if I am an owner or operator of a stationary CI internal combustion engine with a displacement of greater than or equal to 30 liters per cylinder?

Notification, Reports, and Records for Owners and Operators

§60.4214   What are my notification, reporting, and recordkeeping requirements if I am an owner or operator of a stationary CI internal combustion engine?

Special Requirements

§60.4215   What requirements must I meet for engines used in Guam, American Samoa, or the Commonwealth of the Northern Mariana Islands?
§60.4216   What requirements must I meet for engines used in Alaska?
§60.4217   What emission standards must I meet if I am an owner or operator of a stationary internal combustion engine using special fuels?

General Provisions

§60.4218   What parts of the General Provisions apply to me?
§60.4219   What definitions apply to this subpart?
Table 1 to Subpart IIII of Part 60—Emission Standards for Stationary Pre-2007 Model Year Engines With a Displacement of <10 Liters per Cylinder and 2007-2010 Model Year Engines >2,237 KW (3,000 HP) and With a Displacement of <10 Liters per Cylinder
Table 2 to Subpart IIII of Part 60—Emission Standards for 2008 Model Year and Later Emergency Stationary CI ICE <37 KW (50 HP) With a Displacement of <10 Liters per Cylinder
Table 3 to Subpart IIII of Part 60—Certification Requirements for Stationary Fire Pump Engines
Table 4 to Subpart IIII of Part 60—Emission Standards for Stationary Fire Pump Engines
Table 5 to Subpart IIII of Part 60—Labeling and Recordkeeping Requirements for New Stationary Emergency Engines
Table 6 to Subpart IIII of Part 60—Optional 3-Mode Test Cycle for Stationary Fire Pump Engines
Table 7 to Subpart IIII of Part 60—Requirements for Performance Tests for Stationary CI ICE With a Displacement of 30 Liters per Cylinder
Table 8 to Subpart IIII of Part 60—Applicability of General Provisions to Subpart IIII

Subpart JJJJ—Standards of Performance for Stationary Spark Ignition Internal Combustion Engines

What This Subpart Covers

§60.4230   Am I subject to this subpart?

Emission Standards for Manufacturers

§60.4231   What emission standards must I meet if I am a manufacturer of stationary SI internal combustion engines or equipment containing such engines?
§60.4232   How long must my engines meet the emission standards if I am a manufacturer of stationary SI internal combustion engines?

Emission Standards for Owners and Operators

§60.4233   What emission standards must I meet if I am an owner or operator of a stationary SI internal combustion engine?
§60.4234   How long must I meet the emission standards if I am an owner or operator of a stationary SI internal combustion engine?

Other Requirements for Owners and Operators

§60.4235   What fuel requirements must I meet if I am an owner or operator of a stationary SI gasoline fired internal combustion engine subject to this subpart?
§60.4236   What is the deadline for importing or installing stationary SI ICE produced in previous model years?
§60.4237   What are the monitoring requirements if I am an owner or operator of an emergency stationary SI internal combustion engine?

Compliance Requirements for Manufacturers

§60.4238   What are my compliance requirements if I am a manufacturer of stationary SI internal combustion engines ≤19 KW (25 HP) or a manufacturer of equipment containing such engines?
§60.4239   What are my compliance requirements if I am a manufacturer of stationary SI internal combustion engines >19 KW (25 HP) that use gasoline or a manufacturer of equipment containing such engines?
§60.4240   What are my compliance requirements if I am a manufacturer of stationary SI internal combustion engines >19 KW (25 HP) that are rich burn engines that use LPG or a manufacturer of equipment containing such engines?
§60.4241   What are my compliance requirements if I am a manufacturer of stationary SI internal combustion engines participating in the voluntary certification program or a manufacturer of equipment containing such engines?
§60.4242   What other requirements must I meet if I am a manufacturer of stationary SI internal combustion engines or equipment containing stationary SI internal combustion engines or a manufacturer of equipment containing such engines?

Compliance Requirements for Owners and Operators

§60.4243   What are my compliance requirements if I am an owner or operator of a stationary SI internal combustion engine?

Testing Requirements for Owners and Operators

§60.4244   What test methods and other procedures must I use if I am an owner or operator of a stationary SI internal combustion engine?

Notification, Reports, and Records for Owners and Operators

§60.4245   What are my notification, reporting, and recordkeeping requirements if I am an owner or operator of a stationary SI internal combustion engine?

General Provisions

§60.4246   What parts of the General Provisions apply to me?

Mobile Source Provisions

§60.4247   What parts of the mobile source provisions apply to me if I am a manufacturer of stationary SI internal combustion engines or a manufacturer of equipment containing such engines?

Definitions

§60.4248   What definitions apply to this subpart?
Table 1 to Subpart JJJJ of Part 60—NOX, CO, and VOC Emission Standards for Stationary Non-Emergency SI Engines 100 HP (Except Gasoline and Rich Burn LPG), Stationary SI Landfill/Digester Gas Engines, and Stationary Emergency Engines >25 HP
Table 2 to Subpart JJJJ of Part 60—Requirements for Performance Tests
Table 3 to Subpart JJJJ of Part 60—Applicability of General Provisions to Subpart JJJJ
Table 4 to Subpart JJJJ of Part 60—Applicability of Mobile Source Provisions for Manufacturers Participating in the Voluntary Certification Program and Certifying Stationary SI ICE to Emission Standards in Table 1 of Subpart JJJJ

Subpart KKKK—Standards of Performance for Stationary Combustion Turbines

Introduction

§60.4300   What is the purpose of this subpart?

Applicability

§60.4305   Does this subpart apply to my stationary combustion turbine?
§60.4310   What types of operations are exempt from these standards of performance?

Emission Limits

§60.4315   What pollutants are regulated by this subpart?
§60.4320   What emission limits must I meet for nitrogen oxides (NOX)?
§60.4325   What emission limits must I meet for NOX if my turbine burns both natural gas and distillate oil (or some other combination of fuels)?
§60.4330   What emission limits must I meet for sulfur dioxide (SO2)?

General Compliance Requirements

§60.4333   What are my general requirements for complying with this subpart?

Monitoring

§60.4335   How do I demonstrate compliance for NOX if I use water or steam injection?
§60.4340   How do I demonstrate continuous compliance for NOX if I do not use water or steam injection?
§60.4345   What are the requirements for the continuous emission monitoring system equipment, if I choose to use this option?
§60.4350   How do I use data from the continuous emission monitoring equipment to identify excess emissions?
§60.4355   How do I establish and document a proper parameter monitoring plan?
§60.4360   How do I determine the total sulfur content of the turbine's combustion fuel?
§60.4365   How can I be exempted from monitoring the total sulfur content of the fuel?
§60.4370   How often must I determine the sulfur content of the fuel?

Reporting

§60.4375   What reports must I submit?
§60.4380   How are excess emissions and monitor downtime defined for NOX?
§60.4385   How are excess emissions and monitoring downtime defined for SO2?
§60.4390   What are my reporting requirements if I operate an emergency combustion turbine or a research and development turbine?
§60.4395   When must I submit my reports?

Performance Tests

§60.4400   How do I conduct the initial and subsequent performance tests, regarding NOX?
§60.4405   How do I perform the initial performance test if I have chosen to install a NOX-diluent CEMS?
§60.4410   How do I establish a valid parameter range if I have chosen to continuously monitor parameters?
§60.4415   How do I conduct the initial and subsequent performance tests for sulfur?

Definitions

§60.4420   What definitions apply to this subpart?
Table 1 to Subpart KKKK of Part 60—Nitrogen Oxide Emission Limits for New Stationary Combustion Turbines

Subpart LLLL—Standards of Performance for New Sewage Sludge Incineration Units

Introduction

§60.4760   What does this subpart do?
§60.4765   When does this subpart become effective?

Applicability and Delegation of Authority

§60.4770   Does this subpart apply to my sewage sludge incineration unit?
§60.4775   What is a new sewage sludge incineration unit?
§60.4780   What sewage sludge incineration units are exempt from this subpart?
§60.4785   Who implements and enforces this subpart?
§60.4790   How are these new source performance standards structured?
§60.4795   Do all nine components of these new source performance standards apply at the same time?

Preconstruction Siting Analysis

§60.4800   Who must prepare a siting analysis?
§60.4805   What is a siting analysis?

Operator Training and Qualification

§60.4810   What are the operator training and qualification requirements?
§60.4815   When must the operator training course be completed?
§60.4820   How do I obtain my operator qualification?
§60.4825   How do I maintain my operator qualification?
§60.4830   How do I renew my lapsed operator qualification?
§60.4835   What if all the qualified operators are temporarily not accessible?
§60.4840   What site-specific documentation is required and how often must it be reviewed by qualified operators and plant personnel?

Emission Limits, Emission Standards, and Operating Limits and Requirements

§60.4845   What emission limits and standards must I meet and by when?
§60.4850   What operating limits and requirements must I meet and by when?
§60.4855   How do I establish operating limits if I do not use a wet scrubber, fabric filter, electrostatic precipitator, or activated carbon injection, or if I limit emissions in some other manner, to comply with the emission limits?
§60.4860   Do the emission limits, emission standards, and operating limits apply during periods of startup, shutdown, and malfunction?
§60.4861   How do I establish an affirmative defense for exceedance of an emission limit or standard during malfunction?

Initial Compliance Requirements

§60.4865   How and when do I demonstrate initial compliance with the emission limits and standards?
§60.4870   How do I establish my operating limits?
§60.4875   By what date must I conduct the initial air pollution control device inspection and make any necessary repairs?
§60.4880   How do I develop a site-specific monitoring plan for my continuous monitoring, bag leak detection, and ash handling systems, and by what date must I conduct an initial performance evaluation?

Continuous Compliance Requirements

§60.4885   How and when do I demonstrate continuous compliance with the emission limits and standards?
§60.4890   How do I demonstrate continuous compliance with my operating limits?
§60.4895   By what date must I conduct annual air pollution control device inspections and make any necessary repairs?

Performance Testing, Monitoring, and Calibration Requirements

§60.4900   What are the performance testing, monitoring, and calibration requirements for compliance with the emission limits and standards?
§60.4905   What are the monitoring and calibration requirements for compliance with my operating limits?

Recordkeeping and Reporting

§60.4910   What records must I keep?
§60.4915   What reports must I submit?

Title V Operating Permits

§60.4920   Am I required to apply for and obtain a title V operating permit for my unit?
§60.4925   When must I submit a title V permit application for my new SSI unit?

Definitions

§60.4930   What definitions must I know?
Table 1 to Subpart LLLL of Part 60—Emission Limits and Standards for New Fluidized Bed Sewage Sludge Incineration Units
Table 2 to Subpart LLLL of Part 60—Emission Limits and Standards for New Multiple Hearth Sewage Sludge Incineration Units
Table 3 to Subpart LLLL of Part 60—Operating Parameters for New Sewage Sludge Incineration Units
Table 4 to Subpart LLLL of Part 60—Toxic Equivalency Factors
Table 5 to Subpart LLLL of Part 60—Summary of Reporting Requirements for New Sewage Sludge Incineration Units

Subpart MMMM—Emission Guidelines and Compliance Times for Existing Sewage Sludge Incineration Units

Introduction

§60.5000   What is the purpose of this subpart?
§60.5005   Am I affected by this subpart?
§60.5010   Is a state plan required for all states?
§60.5015   What must I include in my state plan?
§60.5020   Is there an approval process for my state plan?
§60.5025   What if my state plan is not approvable?
§60.5030   Is there an approval process for a negative declaration letter?
§60.5035   What compliance schedule must I include in my state plan?
§60.5040   Are there any state plan requirements for this subpart that apply instead of the requirements specified in subpart B?
§60.5045   In lieu of a state plan submittal, are there other acceptable option(s) for a state to meet its section 111(d)/129 (b)(2) obligations?
§60.5050   What authorities will not be delegated to state, local, or tribal agencies?
§60.5055   Does this subpart directly affect SSI unit owners and operators in my state?

Applicability of State Plans

§60.5060   What SSI units must I address in my state plan?
§60.5065   What SSI units are exempt from my state plan?

Use of Model Rule

§60.5070   What is the “model rule” in this subpart?
§60.5075   How does the model rule relate to the required elements of my state plan?
§60.5080   What are the principal components of the model rule?

Model Rule—Increments of Progress

§60.5085   What are my requirements for meeting increments of progress and achieving final compliance?
§60.5090   When must I complete each increment of progress?
§60.5095   What must I include in the notifications of achievement of increments of progress?
§60.5100   When must I submit the notifications of achievement of increments of progress?
§60.5105   What if I do not meet an increment of progress?
§60.5110   How do I comply with the increment of progress for submittal of a control plan?
§60.5115   How do I comply with the increment of progress for achieving final compliance?
§60.5120   What must I do if I close my SSI unit and then restart it?
§60.5125   What must I do if I plan to permanently close my SSI unit and not restart it?

Model Rule—Operator Training and Qualification

§60.5130   What are the operator training and qualification requirements?
§60.5135   When must the operator training course be completed?
§60.5140   How do I obtain my operator qualification?
§60.5145   How do I maintain my operator qualification?
§60.5150   How do I renew my lapsed operator qualification?
§60.5155   What if all the qualified operators are temporarily not accessible?
§60.5160   What site-specific documentation is required and how often must it be reviewed by qualified operators and plant personnel?

Model Rule—Emission Limits, Emission Standards, and Operating Limits and Requirements

§60.5165   What emission limits and standards must I meet and by when?
§60.5170   What operating limits and requirements must I meet and by when?
§60.5175   How do I establish operating limits if I do not use a wet scrubber, fabric filter, electrostatic precipitator, activated carbon injection, or afterburner, or if I limit emissions in some other manner, to comply with the emission limits?
§60.5180   Do the emission limits, emission standards, and operating limits apply during periods of startup, shutdown, and malfunction?
§60.5181   How do I establish an affirmative defense for exceedance of an emission limit or standard during malfunction?

Model Rule—Initial Compliance Requirements

§60.5185   How and when do I demonstrate initial compliance with the emission limits and standards?
§60.5190   How do I establish my operating limits?
§60.5195   By what date must I conduct the initial air pollution control device inspection and make any necessary repairs?
§60.5200   How do I develop a site-specific monitoring plan for my continuous monitoring, bag leak detection, and ash handling systems, and by what date must I conduct an initial performance evaluation?

Model Rule—Continuous Compliance Requirements

§60.5205   How and when do I demonstrate continuous compliance with the emission limits and standards?
§60.5210   How do I demonstrate continuous compliance with my operating limits?
§60.5215   By what date must I conduct annual air pollution control device inspections and make any necessary repairs?

Model Rule—Performance Testing, Monitoring, and Calibration Requirements

§60.5220   What are the performance testing, monitoring, and calibration requirements for compliance with the emission limits and standards?
§60.5225   What are the monitoring and calibration requirements for compliance with my operating limits?

Model Rule—Recordkeeping and Reporting

§60.5230   What records must I keep?
§60.5235   What reports must I submit?

Model Rule—Title V Operating Permits

§60.5240   Am I required to apply for and obtain a Title V operating permit for my existing SSI unit?
§60.5245   When must I submit a title V permit application for my existing SSI unit?

Model Rule-Definitions

§60.5250   What definitions must I know?
Table 1 to Subpart MMMM of Part 60—Model Rule—Increments of Progress and Compliance Schedules for Existing Sewage Sludge Incineration Units
Table 2 to Subpart MMMM of Part 60—Model Rule—Emission Limits and Standards for Existing Fluidized Bed Sewage Sludge Incineration Units
Table 3 to Subpart MMMM of Part 60—Model Rule—Emission Limits and Standards for Existing Multiple Hearth Sewage Sludge Incineration Units
Table 4 to Subpart MMMM of Part 60—Model Rule—Operating Parameters for Existing Sewage Sludge Incineration Units
Table 5 to Subpart MMMM of Part 60—Model Rule—Toxic Equivalency Factors
Table 6 to Subpart MMMM of Part 60—Model Rule—Summary of Reporting Requirements for Existing Sewage Sludge Incineration Units

Subpart OOOO—Standards of Performance for Crude Oil and Natural Gas Production, Transmission and Distribution

§60.5360   What is the purpose of this subpart?
§60.5365   Am I subject to this subpart?
§60.5370   When must I comply with this subpart?
§60.5375   What standards apply to gas well affected facilities?
§60.5380   What standards apply to centrifugal compressor affected facilities?
§60.5385   What standards apply to reciprocating compressor affected facilities?
§60.5390   What standards apply to pneumatic controller affected facilities?
§60.5395   What standards apply to storage vessel affected facilities?
§60.5400   What equipment leak standards apply to affected facilities at an onshore natural gas processing plant?
§60.5401   What are the exceptions to the equipment leak standards for affected facilities at onshore natural gas processing plants?
§60.5402   What are the alternative emission limitations for equipment leaks from onshore natural gas processing plants?
§60.5405   What standards apply to sweetening units at onshore natural gas processing plants?
§60.5406   What test methods and procedures must I use for my sweetening units affected facilities at onshore natural gas processing plants?
§60.5407   What are the requirements for monitoring of emissions and operations from my sweetening unit affected facilities at onshore natural gas processing plants?
§60.5408   What is an optional procedure for measuring hydrogen sulfide in acid gas—Tutwiler Procedure?
§60.5410   How do I demonstrate initial compliance with the standards for my gas well affected facility, my centrifugal compressor affected facility, my reciprocating compressor affected facility, my pneumatic controller affected facility, my storage vessel affected facility, and my equipment leaks and sweetening unit affected facilities at onshore natural gas processing plants?
§60.5411   What additional requirements must I meet to determine initial compliance for my covers and closed vent systems routing materials from storage vessels and centrifugal compressor wet seal degassing systems?
§60.5412   What additional requirements must I meet for determining initial compliance with control devices used to comply with the emission standards for my storage vessel or centrifugal compressor affected facility?
§60.5413   What are the performance testing procedures for control devices used to demonstrate compliance at my storage vessel or centrifugal compressor affected facility?
§60.5415   How do I demonstrate continuous compliance with the standards for my gas well affected facility, my centrifugal compressor affected facility, my stationary reciprocating compressor affected facility, my pneumatic controller affected facility, my storage vessel affected facility, and my affected facilities at onshore natural gas processing plants?
§60.5416   What are the initial and continuous cover and closed vent system inspection and monitoring requirements for my storage vessel and centrifugal compressor affected facility?
§60.5417   What are the continuous control device monitoring requirements for my storage vessel or centrifugal compressor affected facility?
§60.5420   What are my notification, reporting, and recordkeeping requirements?
§60.5421   What are my additional recordkeeping requirements for my affected facility subject to VOC requirements for onshore natural gas processing plants?
§60.5422   What are my additional reporting requirements for my affected facility subject to VOC requirements for onshore natural gas processing plants?
§60.5423   What additional recordkeeping and reporting requirements apply to my sweetening unit affected facilities at onshore natural gas processing plants?
§60.5425   What part of the General Provisions apply to me?
§60.5430   What definitions apply to this subpart?
§§60.5431-60.5499   [Reserved]
Table 1 to Subpart OOOO of Part 60—Required Minimum Initial SO2 Emission Reduction Efficiency (Zi)
Table 2 to Subpart OOOO of Part 60—Required Minimum SO2 Emission Reduction Efficiency (Zc)
Table 3 to Subpart OOOO of Part 60—Applicability of General Provisions to Subpart OOOO

Authority: 42 U.S.C. 7401 et seq.

Source: 36 FR 24877, Dec. 23, 1971, unless otherwise noted.

Subpart A—General Provisions

§60.1   Applicability.

(a) Except as provided in subparts B and C, the provisions of this part apply to the owner or operator of any stationary source which contains an affected facility, the construction or modification of which is commenced after the date of publication in this part of any standard (or, if earlier, the date of publication of any proposed standard) applicable to that facility.

(b) Any new or revised standard of performance promulgated pursuant to section 111(b) of the Act shall apply to the owner or operator of any stationary source which contains an affected facility, the construction or modification of which is commenced after the date of publication in this part of such new or revised standard (or, if earlier, the date of publication of any proposed standard) applicable to that facility.

(c) In addition to complying with the provisions of this part, the owner or operator of an affected facility may be required to obtain an operating permit issued to stationary sources by an authorized State air pollution control agency or by the Administrator of the U.S. Environmental Protection Agency (EPA) pursuant to Title V of the Clean Air Act (Act) as amended November 15, 1990 (42 U.S.C. 7661). For more information about obtaining an operating permit see part 70 of this chapter.

(d) Site-specific standard for Merck & Co., Inc.'s Stonewall Plant in Elkton, Virginia. (1) This paragraph applies only to the pharmaceutical manufacturing facility, commonly referred to as the Stonewall Plant, located at Route 340 South, in Elkton, Virginia (“site”).

(2) Except for compliance with 40 CFR 60.49b(u), the site shall have the option of either complying directly with the requirements of this part, or reducing the site-wide emissions caps in accordance with the procedures set forth in a permit issued pursuant to 40 CFR 52.2454. If the site chooses the option of reducing the site-wide emissions caps in accordance with the procedures set forth in such permit, the requirements of such permit shall apply in lieu of the otherwise applicable requirements of this part.

(3) Notwithstanding the provisions of paragraph (d)(2) of this section, for any provisions of this part except for Subpart Kb, the owner/operator of the site shall comply with the applicable provisions of this part if the Administrator determines that compliance with the provisions of this part is necessary for achieving the objectives of the regulation and the Administrator notifies the site in accordance with the provisions of the permit issued pursuant to 40 CFR 52.2454.

[40 FR 53346, Nov. 17, 1975, as amended at 55 FR 51382, Dec. 13, 1990; 59 FR 12427, Mar. 16, 1994; 62 FR 52641, Oct. 8, 1997]

§60.2   Definitions.

The terms used in this part are defined in the Act or in this section as follows:

Act means the Clean Air Act (42 U.S.C. 7401 et seq.)

Administrator means the Administrator of the Environmental Protection Agency or his authorized representative.

Affected facility means, with reference to a stationary source, any apparatus to which a standard is applicable.

Alternative method means any method of sampling and analyzing for an air pollutant which is not a reference or equivalent method but which has been demonstrated to the Administrator's satisfaction to, in specific cases, produce results adequate for his determination of compliance.

Approved permit program means a State permit program approved by the Administrator as meeting the requirements of part 70 of this chapter or a Federal permit program established in this chapter pursuant to Title V of the Act (42 U.S.C. 7661).

Capital expenditure means an expenditure for a physical or operational change to an existing facility which exceeds the product of the applicable “annual asset guideline repair allowance percentage” specified in the latest edition of Internal Revenue Service (IRS) Publication 534 and the existing facility's basis, as defined by section 1012 of the Internal Revenue Code. However, the total expenditure for a physical or operational change to an existing facility must not be reduced by any “excluded additions” as defined in IRS Publication 534, as would be done for tax purposes.

Clean coal technology demonstration project means a project using funds appropriated under the heading ‘Department of Energy-Clean Coal Technology’, up to a total amount of $2,500,000,000 for commercial demonstrations of clean coal technology, or similar projects funded through appropriations for the Environmental Protection Agency.

Commenced means, with respect to the definition of new source in section 111(a)(2) of the Act, that an owner or operator has undertaken a continuous program of construction or modification or that an owner or operator has entered into a contractual obligation to undertake and complete, within a reasonable time, a continuous program of construction or modification.

Construction means fabrication, erection, or installation of an affected facility.

Continuous monitoring system means the total equipment, required under the emission monitoring sections in applicable subparts, used to sample and condition (if applicable), to analyze, and to provide a permanent record of emissions or process parameters.

Electric utility steam generating unit means any steam electric generating unit that is constructed for the purpose of supplying more than one-third of its potential electric output capacity and more than 25 MW electrical output to any utility power distribution system for sale. Any steam supplied to a steam distribution system for the purpose of providing steam to a steam-electric generator that would produce electrical energy for sale is also considered in determining the electrical energy output capacity of the affected facility.

Equivalent method means any method of sampling and analyzing for an air pollutant which has been demonstrated to the Administrator's satisfaction to have a consistent and quantitatively known relationship to the reference method, under specified conditions.

Excess Emissions and Monitoring Systems Performance Report is a report that must be submitted periodically by a source in order to provide data on its compliance with stated emission limits and operating parameters, and on the performance of its monitoring systems.

Existing facility means, with reference to a stationary source, any apparatus of the type for which a standard is promulgated in this part, and the construction or modification of which was commenced before the date of proposal of that standard; or any apparatus which could be altered in such a way as to be of that type.

Force majeure means, for purposes of §60.8, an event that will be or has been caused by circumstances beyond the control of the affected facility, its contractors, or any entity controlled by the affected facility that prevents the owner or operator from complying with the regulatory requirement to conduct performance tests within the specified timeframe despite the affected facility's best efforts to fulfill the obligation. Examples of such events are acts of nature, acts of war or terrorism, or equipment failure or safety hazard beyond the control of the affected facility.

Isokinetic sampling means sampling in which the linear velocity of the gas entering the sampling nozzle is equal to that of the undisturbed gas stream at the sample point.

Issuance of a part 70 permit will occur, if the State is the permitting authority, in accordance with the requirements of part 70 of this chapter and the applicable, approved State permit program. When the EPA is the permitting authority, issuance of a Title V permit occurs immediately after the EPA takes final action on the final permit.

Malfunction means any sudden, infrequent, and not reasonably preventable failure of air pollution control equipment, process equipment, or a process to operate in a normal or usual manner. Failures that are caused in part by poor maintenance or careless operation are not malfunctions.

Modification means any physical change in, or change in the method of operation of, an existing facility which increases the amount of any air pollutant (to which a standard applies) emitted into the atmosphere by that facility or which results in the emission of any air pollutant (to which a standard applies) into the atmosphere not previously emitted.

Monitoring device means the total equipment, required under the monitoring of operations sections in applicable subparts, used to measure and record (if applicable) process parameters.

Nitrogen oxides means all oxides of nitrogen except nitrous oxide, as measured by test methods set forth in this part.

One-hour period means any 60-minute period commencing on the hour.

Opacity means the degree to which emissions reduce the transmission of light and obscure the view of an object in the background.

Owner or operator means any person who owns, leases, operates, controls, or supervises an affected facility or a stationary source of which an affected facility is a part.

Part 70 permit means any permit issued, renewed, or revised pursuant to part 70 of this chapter.

Particulate matter means any finely divided solid or liquid material, other than uncombined water, as measured by the reference methods specified under each applicable subpart, or an equivalent or alternative method.

Permit program means a comprehensive State operating permit system established pursuant to title V of the Act (42 U.S.C. 7661) and regulations codified in part 70 of this chapter and applicable State regulations, or a comprehensive Federal operating permit system established pursuant to title V of the Act and regulations codified in this chapter.

Permitting authority means:

(1) The State air pollution control agency, local agency, other State agency, or other agency authorized by the Administrator to carry out a permit program under part 70 of this chapter; or

(2) The Administrator, in the case of EPA-implemented permit programs under title V of the Act (42 U.S.C. 7661).

Proportional sampling means sampling at a rate that produces a constant ratio of sampling rate to stack gas flow rate.

Reactivation of a very clean coal-fired electric utility steam generating unit means any physical change or change in the method of operation associated with the commencement of commercial operations by a coal-fired utility unit after a period of discontinued operation where the unit:

(1) Has not been in operation for the two-year period prior to the enactment of the Clean Air Act Amendments of 1990, and the emissions from such unit continue to be carried in the permitting authority's emissions inventory at the time of enactment;

(2) Was equipped prior to shut-down with a continuous system of emissions control that achieves a removal efficiency for sulfur dioxide of no less than 85 percent and a removal efficiency for particulates of no less than 98 percent;

(3) Is equipped with low-NOX burners prior to the time of commencement of operations following reactivation; and

(4) Is otherwise in compliance with the requirements of the Clean Air Act.

Reference method means any method of sampling and analyzing for an air pollutant as specified in the applicable subpart.

Repowering means replacement of an existing coal-fired boiler with one of the following clean coal technologies: atmospheric or pressurized fluidized bed combustion, integrated gasification combined cycle, magnetohydrodynamics, direct and indirect coal-fired turbines, integrated gasification fuel cells, or as determined by the Administrator, in consultation with the Secretary of Energy, a derivative of one or more of these technologies, and any other technology capable of controlling multiple combustion emissions simultaneously with improved boiler or generation efficiency and with significantly greater waste reduction relative to the performance of technology in widespread commercial use as of November 15, 1990. Repowering shall also include any oil and/or gas-fired unit which has been awarded clean coal technology demonstration funding as of January 1, 1991, by the Department of Energy.

Run means the net period of time during which an emission sample is collected. Unless otherwise specified, a run may be either intermittent or continuous within the limits of good engineering practice.

Shutdown means the cessation of operation of an affected facility for any purpose.

Six-minute period means any one of the 10 equal parts of a one-hour period.

Standard means a standard of performance proposed or promulgated under this part.

Standard conditions means a temperature of 293 K (68F) and a pressure of 101.3 kilopascals (29.92 in Hg).

Startup means the setting in operation of an affected facility for any purpose.

State means all non-Federal authorities, including local agencies, interstate associations, and State-wide programs, that have delegated authority to implement: (1) The provisions of this part; and/or (2) the permit program established under part 70 of this chapter. The term State shall have its conventional meaning where clear from the context.

Stationary source means any building, structure, facility, or installation which emits or may emit any air pollutant.

Title V permit means any permit issued, renewed, or revised pursuant to Federal or State regulations established to implement title V of the Act (42 U.S.C. 7661). A title V permit issued by a State permitting authority is called a part 70 permit in this part.

Volatile Organic Compound means any organic compound which participates in atmospheric photochemical reactions; or which is measured by a reference method, an equivalent method, an alternative method, or which is determined by procedures specified under any subpart.

[44 FR 55173, Sept. 25, 1979, as amended at 45 FR 5617, Jan. 23, 1980; 45 FR 85415, Dec. 24, 1980; 54 FR 6662, Feb. 14, 1989; 55 FR 51382, Dec. 13, 1990; 57 FR 32338, July 21, 1992; 59 FR 12427, Mar. 16, 1994; 72 FR 27442, May 16, 2007]

§60.3   Units and abbreviations.

Used in this part are abbreviations and symbols of units of measure. These are defined as follows:

(a) System International (SI) units of measure:

A—ampere

g—gram

Hz—hertz

J—joule

K—degree Kelvin

kg—kilogram

m—meter

m3—cubic meter

mg—milligram—10−3 gram

mm—millimeter—10−3 meter

Mg—megagram—106 gram

mol—mole

N—newton

ng—nanogram—10−9 gram

nm—nanometer—10−9 meter

Pa—pascal

s—second

V—volt

W—watt

Ω—ohm

µg—microgram—10−6 gram

(b) Other units of measure:

Btu—British thermal unit

°C—degree Celsius (centigrade)

cal—calorie

cfm—cubic feet per minute

cu ft—cubic feet

dcf—dry cubic feet

dcm—dry cubic meter

dscf—dry cubic feet at standard conditions

dscm—dry cubic meter at standard conditions

eq—equivalent

°F—degree Fahrenheit

ft—feet

gal—gallon

gr—grain

g-eq—gram equivalent

hr—hour

in—inch

k—1,000

l—liter

lpm—liter per minute

lb—pound

meq—milliequivalent

min—minute

ml—milliliter

mol. wt.—molecular weight

ppb—parts per billion

ppm—parts per million

psia—pounds per square inch absolute

psig—pounds per square inch gage

°R—degree Rankine

scf—cubic feet at standard conditions

scfh—cubic feet per hour at standard conditions

scm—cubic meter at standard conditions

sec—second

sq ft—square feet

std—at standard conditions

(c) Chemical nomenclature:

CdS—cadmium sulfide

CO—carbon monoxide

CO2—carbon dioxide

HCl—hydrochloric acid

Hg—mercury

H2O—water

H2S—hydrogen sulfide

H2SO4—sulfuric acid

N2—nitrogen

NO—nitric oxide

NO2—nitrogen dioxide

NOX—nitrogen oxides

O2—oxygen

SO2—sulfur dioxide

SO3—sulfur trioxide

SOX—sulfur oxides

(d) Miscellaneous:

A.S.T.M.—American Society for Testing and Materials

[42 FR 37000, July 19, 1977; 42 FR 38178, July 27, 1977]

§60.4   Address.

Link to an amendment published at 79 FR 60995, Oct. 9, 2014.

(a) All requests, reports, applications, submittals, and other communications to the Administrator pursuant to this part shall be submitted in duplicate to the appropriate Regional Office of the U.S. Environmental Protection Agency to the attention of the Director of the Division indicated in the following list of EPA Regional Offices.

Region I (Connecticut, Maine, Massachusetts, New Hampshire, Rhode Island, Vermont), Director, Office of Ecosystem Protection, U.S. Environmental Protection Agency, 5 Post Office Square—Suite 100, Boston, MA 02109-3912.

Region II (New Jersey, New York, Puerto Rico, Virgin Islands), Director, Air and Waste Management Division, U.S. Environmental Protection Agency, Federal Office Building, 26 Federal Plaza (Foley Square), New York, NY 10278.

Region III (Delaware, District of Columbia, Maryland, Pennsylvania, Virginia, West Virginia), Director, Air Protection Division, Mail Code 3AP00, 1650 Arch Street, Philadelphia, PA 19103-2029.

Region IV (Alabama, Florida, Georgia, Kentucky, Mississippi, North Carolina, South Carolina, Tennessee), Director, Air, Pesticides and Toxics Management Division, U.S. Environmental Protection Agency, 61 Forsyth St. SW., Suite 9T43, Atlanta, Georgia 30303-8960.

Region V (Illinois, Indiana, Michigan, Minnesota, Ohio, Wisconsin), Director, Air and Radiation Division, U.S. Environmental Protection Agency, 77 West Jackson Boulevard, Chicago, IL 60604-3590.

Region VI (Arkansas, Louisiana, New Mexico, Oklahoma, Texas); Director; Air, Pesticides, and Toxics Division; U.S. Environmental Protection Agency, 1445 Ross Avenue, Dallas, TX 75202.

Region VII (Iowa, Kansas, Missouri, Nebraska), Director, Air and Waste Management Division, 11201 Renner Boulevard, Lenexa, Kansas 66219.

Region VIII (Colorado, Montana, North Dakota, South Dakota, Utah, Wyoming) Director, Air and Toxics Technical Enforcement Program, Office of Enforcement, Compliance and Environmental Justice, Mail Code 8ENF-AT, 1595 Wynkoop Street, Denver, CO 80202-1129.

Region IX (Arizona, California, Hawaii and Nevada; the territories of American Samoa and Guam; the Commonwealth of the Northern Mariana Islands; the territories of Baker Island, Howland Island, Jarvis Island, Johnston Atoll, Kingman Reef, Midway Atoll, Palmyra Atoll, and Wake Islands; and certain U.S. Government activities in the freely associated states of the Republic of the Marshall Islands, the Federated States of Micronesia, and the Republic of Palau), Director, Air Division, U.S. Environmental Protection Agency, 75 Hawthorne Street, San Francisco, CA 94105.

Region X (Alaska, Oregon, Idaho, Washington), Director, Air and Waste Management Division, U.S. Environmental Protection Agency, 1200 Sixth Avenue, Seattle, WA 98101.

(b) Section 111(c) directs the Administrator to delegate to each State, when appropriate, the authority to implement and enforce standards of performance for new stationary sources located in such State. All information required to be submitted to EPA under paragraph (a) of this section, must also be submitted to the appropriate State Agency of any State to which this authority has been delegated (provided, that each specific delegation may except sources from a certain Federal or State reporting requirement). The appropriate mailing address for those States whose delegation request has been approved is as follows:

(A) [Reserved]

(B) State of Alabama: Alabama Department of Environmental Management, P.O. Box 301463, Montgomery, Alabama 36130-1463.

(C) State of Alaska, Department of Environmental Conservation, Pouch O, Juneau, AK 99811.

(D) Arizona:

Arizona Department of Environmental Quality, 1110 West Washington Street, Phoenix, AZ 85007.

Maricopa County Air Quality Department, 1001 North Central Avenue, Suite 900, Phoenix, AZ 85004.

Pima County Department of Environmental Quality, 33 North Stone Avenue, Suite 700, Tucson, AZ 85701.

Pinal County Air Quality Control District, 31 North Pinal Street, Building F, Florence, AZ 85132.

Note: For tables listing the delegation status of agencies in Region IX, see paragraph (d) of this section.

(E) State of Arkansas: Chief, Division of Air Pollution Control, Arkansas Department of Pollution Control and Ecology, 8001 National Drive, P.O. Box 9583, Little Rock, AR 72209.

(F) California:

Amador County Air Pollution Control District, 12200-B Airport Road, Jackson, CA 95642.

Antelope Valley Air Quality Management District, 43301 Division Street, Suite 206, Lancaster, CA 93535.

Bay Area Air Quality Management District, 939 Ellis Street, San Francisco, CA 94109.

Butte County Air Quality Management District, 2525 Dominic Drive, Suite J, Chico, CA 95928.

Calaveras County Air Pollution Control District, 891 Mountain Ranch Road, San Andreas, CA 95249.

Colusa County Air Pollution Control District, 100 Sunrise Blvd., Suite A-3, Colusa, CA 95932-3246.

El Dorado County Air Quality Management District, 2850 Fairlane Court, Bldg. C, Placerville, CA 95667-4100.

Eastern Kern Air Pollution Control District, 2700 “M” Street, Suite 302, Bakersfield, CA 93301-2370.

Feather River Air Quality Management District, 1007 Live Oak Blvd., Suite B-3, Yuba City, CA 95991.

Glenn County Air Pollution Control District, 720 N. Colusa Street, P.O. Box 351, Willows, CA 95988-0351.

Great Basin Unified Air Pollution Control District, 157 Short Street, Suite 6, Bishop, CA 93514-3537.

Imperial County Air Pollution Control District, 150 South Ninth Street, El Centro, CA 92243-2801.

Lake County Air Quality Management District, 885 Lakeport Blvd., Lakeport, CA 95453-5405.

Lassen County Air Pollution Control District, 707 Nevada Street, Suite 1, Susanville, CA 96130.

Mariposa County Air Pollution Control District, P.O. Box 5, Mariposa, CA 95338.

Mendocino County Air Quality Management District, 306 E. Gobbi Street, Ukiah, CA 95482-5511.

Modoc County Air Pollution Control District, 619 North Main Street, Alturas, CA 96101.

Mojave Desert Air Quality Management District, 14306 Park Avenue, Victorville, CA 92392-2310.

Monterey Bay Unified Air Pollution Control District, 24580 Silver Cloud Court, Monterey, CA 93940.

North Coast Unified Air Quality Management District, 2300 Myrtle Avenue, Eureka, CA 95501-3327.

Northern Sierra Air Quality Management District, 200 Litton Drive, Suite 320, P.O. Box 2509, Grass Valley, CA 95945-2509.

Northern Sonoma County Air Pollution Control District, 150 Matheson Street, Healdsburg, CA 95448-4908.

Placer County Air Pollution Control District, 3091 County Center Drive, Suite 240, Auburn, CA 95603.

Sacramento Metropolitan Air Quality Management District, 777 12th Street, Third Floor, Sacramento, CA 95814-1908.

San Diego County Air Pollution Control District, 10124 Old Grove Road, San Diego, CA 92131-1649.

San Joaquin Valley Air Pollution Control District, 1990 E. Gettysburg, Fresno, CA 93726.

San Luis Obispo County Air Pollution Control District, 3433 Roberto Court, San Luis Obispo, CA 93401-7126.

Santa Barbara County Air Pollution Control District, 260 North San Antonio Road, Suite A, Santa Barbara, CA 93110-1315.

Shasta County Air Quality Management District, 1855 Placer Street, Suite 101, Redding, CA 96001-1759.

Siskiyou County Air Pollution Control District, 525 So. Foothill Drive, Yreka, CA 96097-3036.

South Coast Air Quality Management District, 21865 Copley Drive, Diamond Bar, CA 91765-4182.

Tehama County Air Pollution Control District, P.O. Box 8069 (1750 Walnut Street), Red Bluff, CA 96080-0038.

Tuolumne County Air Pollution Control District, 22365 Airport, Columbia, CA 95310.

Ventura County Air Pollution Control District, 669 County Square Drive, 2nd Floor, Ventura, CA 93003-5417.

Yolo-Solano Air Quality Management District, 1947 Galileo Court, Suite 103, Davis, CA 95616-4882.

Note: For tables listing the delegation status of agencies in Region IX, see paragraph (d) of this section.

(G) State of Colorado, Department of Public Health and Environment, 4300 Cherry Creek Drive South, Denver, CO 80222-1530.

Note: For a table listing Region VIII's NSPS delegation status, see paragraph (c) of this section.

(H) State of Connecticut, Bureau of Air Management, Department of Environmental Protection, State Office Building, 165 Capitol Avenue, Hartford, CT 06106.

(I) State of Delaware, Department of Natural Resources & Environmental Control, 89 Kings Highway, P.O. Box 1401, Dover, Delaware 19903.

(J) District of Columbia, Department of Public Health, Air Quality Division, 51 N Street, NE., Washington, DC 20002.

(K) State of Florida: Florida Department of Environmental Protection, Division of Air Resources Management, 2600 Blair Stone Road, MS 5500, Tallahassee, Florida 32399-2400.

(L) State of Georgia: Georgia Department of Natural Resources, Environmental Protection Division, Air Protection Branch, 4244 International Parkway, Suite 120, Atlanta, Georgia 30354.

(M) Hawaii:

Clean Air Branch, Hawaii Department of Health, 919 Ala Moana Blvd., Suite 203, Honolulu, HI 96814.

Note: For tables listing the delegation status of agencies in Region IX, see paragraph (d) of this section.

(N) State of Idaho, Department of Health and Welfare, Statehouse, Boise, ID 83701.

(O) State of Illinois: Illinois Environmental Protection Agency, 1021 North Grand Avenue East, Springfield, Illinois 62794.

(P) State of Indiana: Indiana Department of Environmental Management, Office of Air Quality, 100 North Senate Avenue, Indianapolis, Indiana 46204.

(Q) State of Iowa: Iowa Department of Natural Resources, Environmental Protection Division, Air Quality Bureau, 7900 Hickman Road, Suite 1, Urbandale, IA 50322.

(R) State of Kansas: Kansas Department of Health and Environment, Bureau of Air and Radiation, 1000 S.W. Jackson, Suite 310, Topeka, KS 66612-1366.

(S) Commonwealth of Kentucky: Commonwealth of Kentucky, Energy and Environment Cabinet, Department of Environmental Protection, Division for Air Quality, 200 Fair Oaks Lane, 1st Floor, Frankfort, Kentucky 40610-1403.

Louisville Metro Air Pollution Control District, 850 Barret Avenue, Louisville, Kentucky 40204.

(T) State Louisiana: Louisiana Department of Environmental Quality, P.O. Box 4301, Baton Rouge, Louisiana 70821-4301. For a list of delegated standards for Louisiana (excluding Indian country), see paragraph (e)(2) of this section.

(U) State of Maine, Bureau of Air Quality Control, Department of Environmental Protection, State House, Station No. 17, Augusta, ME 04333.

(V) State of Maryland, Department of the Environment, 1800 Washington Boulevard, Suite 705, Baltimore, Maryland 21230.

(W) Commonwealth of Massachusetts, Division of Air Quality Control, Department of Environmental Protection, One Winter Street, 7th floor, Boston, MA 02108.

(X) State of Michigan: Michigan Department of Natural Resources and Environment, Air Quality Division, P.O. Box 30028, Lansing, Michigan 48909.

(Y) State of Minnesota: Minnesota Pollution Control Agency, Division of Air Quality, 520 Lafayette Road North, St. Paul, Minnesota 55155.

(Z) State of Mississippi: Hand Deliver or Courier: Mississippi Department of Environmental Quality, Office of Pollution Control, Air Division, 515 East Amite Street, Jackson, Mississippi 39201, Mailing Address: Mississippi Department of Environmental Quality, Office of Pollution Control, Air Division, P.O. Box 2261, Jackson, Mississippi 39225.

(AA) State of Missouri: Missouri Department of Natural Resources, Division of Environmental Quality, P.O. Box 176, Jefferson City, MO 65102.

(BB) State of Montana, Department of Environmental Quality, 1520 E. 6th Ave., PO Box 200901, Helena, MT 59620-0901.

Note: For a table listing Region VIII's NSPS delegation status, see paragraph (c) of this section.

(CC) State of Nebraska, Nebraska Department of Environmental Control, P.O. Box 94877, State House Station, Lincoln, NE 68509.

Lincoln-Lancaster County Health Department, Division of Environmental Health, 2200 St. Marys Avenue, Lincoln, NE 68502

(DD) Nevada:

Nevada Division of Environmental Protection, 901 South Stewart Street, Suite 4001, Carson City, NV 89701-5249.

Clark County Department of Air Quality and Environmental Management, 500 S. Grand Central Parkway, 1st Floor, P.O. Box 555210, Las Vegas, NV 89155-5210.

Washoe County Health District, Air Quality Management Division, 1001 E. 9th Street, Building A, Suite 115A, Reno, NV 89520.

Note: For tables listing the delegation status of agencies in Region IX, see paragraph (d) of this section.

(EE) State of New Hampshire, Air Resources Division, Department of Environmental Services, 64 North Main Street, Caller Box 2033, Concord, NH 03302-2033.

(FF) State of New Jersey: New Jersey Department of Environmental Protection, Division of Environmental Quality, Enforcement Element, John Fitch Plaza, CN-027, Trenton, NJ 08625.

(1) The following table lists the specific source and pollutant categories that have been delegated to the states in Region II. The (X) symbol is used to indicate each category that has been delegated.

  Subpart State
New JerseyNew YorkPuerto RicoVirgin Islands
DFossil-Fuel Fired Steam Generators for Which Construction Commenced After August 17, 1971 (Steam Generators and Lignite Fired Steam Generators)XXXX
DaElectric Utility Steam Generating Units for Which Construction Commenced After September 18, 1978XX
DbIndustrial-Commercial-Institutional Steam Generating UnitsXXXX
EIncineratorsXXXX
FPortland Cement PlantsXXXX
GNitric Acid PlantsXXXX
HSulfuric Acid PlantsXXXX
IAsphalt Concrete PlantsXXXX
JPetroleum Refineries—(All Categories)XXXX
KStorage Vessels for Petroleum Liquids Constructed After June 11, 1973, and prior to May 19, 1978XXXX
KaStorage Vessels for Petroleum Liquids Constructed After May 18, 1978XXX
LSecondary Lead SmeltersXXXX
MSecondary Brass and Bronze Ingot Production PlantsXXXX
NIron and Steel PlantsXXXX
OSewage Treatment PlantsXXXX
PPrimary Copper SmeltersXXXX
QPrimary Zinc SmeltersXXXX
RPrimary Lead SmeltersXXXX
SPrimary Aluminum Reduction PlantsXXXX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsXXXX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsXXXX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsXXXX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsXXXX
XPhosphate Fertilizer Industry: Granular Triple SuperphosphateXXXX
YCoal Preparation PlantsXXXX
ZFerroally Production FacilitiesXXXX
AASteel Plants: Electric Arc FurnacesXXXX
AAaElectric Arc Furnaces and Argon-Oxygen Decarburization Vessels in Steel PlantsXXX
BBKraft Pulp MillsXXX
CCGlass Manufacturing PlantsXXX
DDGrain ElevatorsXXX
EESurface Coating of Metal FurnitureXXX
GGStationary Gas TurbinesXXX
HHLime PlantsXXX
KKLead Acid Battery Manufacturing PlantsXX
LLMetallic Mineral Processing PlantsXXX
MMAutomobile and Light-Duty Truck Surface Coating OperationsXX
NNPhosphate Rock PlantsXX
PPAmmonium Sulfate Manufacturing PlantsXX
QQGraphic Art Industry Publication Rotogravure PrintingXXXX
RRPressure Sensitive Tape and Label Surface Coating OperationsXXX
SSIndustrial Surface Coating: Large AppliancesXXX
TTMetal Coil Surface CoatingXXX
UUAsphalt Processing and Asphalt Roofing ManufactureXXX
VVEquipment Leaks of Volatile Organic Compounds in Synthetic Organic Chemical Manufacturing IndustryXX
WWBeverage Can Surface Coating IndustryXXX
XXBulk Gasoline TerminalsXXX
FFFFlexible Vinyl and Urethane Coating and PrintingXXX
GGGEquipment Leaks of VOC in Petroleum RefineriesXX
HHHSynthetic Fiber Production FacilitiesXX
JJJPetroleum Dry ClearnersXXX
KKKEquipment Leaks of VOC from Onshore Natural Gas Processing Plants
LLLOnshore Natural Gas Processing Plants; SO2 EmissionsX
OOONonmetallic Mineral Processing PlantsXX
PPPWool Fiberglass Insulation Manufacturing PlantsXX

(GG) State of New Mexico: New Mexico Environment Department, 1190 St. Francis Drive, P.O. Box 26110, Santa Fe, New Mexico 87502. Note: For a list of delegated standards for New Mexico (excluding Bernalillo County and Indian country), see paragraph (e)(1) of this section.

(i) Albuquerque-Bernalillo County Air Quality Control Board, c/o Environmental Health Department, P.O. Box 1293, Albuquerque, New Mexico 87103.

(ii) [Reserved]

(HH) New York: New York State Department of Environmental Conservation, 50 Wolf Road Albany, New York 12233, attention: Division of Air Resources.

(II) State of North Carolina: North Carolina Department of Environment and Natural Resources, Division of Air Quality, 1641 Mail Service Center, Raleigh, North Carolina 27699-1641 or local agencies, Forsyth County Environmental Affairs, 201 North Chestnut Street, Winston-Salem, North Carolina 27101 or Forsyth County Air Quality Section, 537 North Spruce Street, Winston-Salem, North Carolina 27101; Mecklenburg County Land Use & Environmental Services Agency, Air Quality, 700 N. Tryon St., Suite 205, Charlotte, North Carolina 28202-2236; Western North Carolina Regional Air Quality Agency, 49 Mount Carmel Road, Asheville, North Carolina 28806.

(JJ) State of North Dakota, Division of Air Quality, North Dakota Department of Health, P.O. Box 5520, Bismarck, ND 58506-5520.

Note: For a table listing Region VIII's NSPS delegation status, see paragraph (c) of this section.

(KK) State of Ohio:

(i) Medina, Summit and Portage Counties; Director, Akron Regional Air Quality Management District, 146 South High Street, Room 904, Akron, OH 44308.

(ii) Stark County; Director, Canton City Health Department, Air Pollution Control Division, 420 Market Avenue North, Canton, Ohio 44702-1544.

(iii) Butler, Clermont, Hamilton, and Warren Counties; Director, Hamilton County Department of Environmental Services, 250 William Howard Taft Road, Cincinnati, Ohio 45219-2660.

(iv) Cuyahoga County; Commissioner, Cleveland Department of Public Health, Division of Air Quality, 75 Erieview Plaza 2nd Floor, Cleveland, Ohio 44114.

(v) Clark, Darke, Greene, Miami, Montgomery, and Preble Counties; Director, Regional Air Pollution Control Agency, 117 South Main Street, Dayton, Ohio 45422-1280.

(vi) Lucas County and the City of Rossford (in Wood County); Director, City of Toledo, Division of Environmental Services, 348 South Erie Street, Toledo, OH 43604.

(vii) Adams, Brown, Lawrence, and Scioto Counties; Portsmouth Local Air Agency, 605 Washington Street, Third Floor, Portsmouth, OH 45662.

(viii) Allen, Ashland, Auglaize, Crawford, Defiance, Erie, Fulton, Hancock, Hardin, Henry, Huron, Marion, Mercer, Ottawa, Paulding, Putnam, Richland, Sandusky, Seneca, Van Wert Williams, Wood (Except City of Rossford), and Wyandot Counties; Ohio Environmental Protection Agency, Northwest District Office, Air Pollution Control, 347 North Dunbridge Road, Bowling Green, Ohio 43402.

(ix) Ashtabula, Caroll, Colombiana, Holmes, Lorain, and Wayne Counties; Ohio Environmental Protection Agency, Northeast District Office, Air Pollution Unit, 2110 East Aurora Road, Twinsburg, OH 44087.

(x) Athens, Belmont, Coshocton, Gallia, Guemsey, Harrison, Hocking, Jackson, Jefferson, Meigs, Monroe, Morgan, Muskingum, Noble, Perry, Pike, Ross, Tuscarawas, Vinton, and Washington Counties; Ohio Environmental Protection Agency, Southeast District Office, Air Pollution Unit, 2195 Front Street, Logan, OH 43138.

(xi) Champaign, Clinton, Highland, Logan, and Shelby Counties; Ohio Environmental Protection Agency, Southwest District Office, Air Pollution Unit, 401 East Fifth Street, Dayton, Ohio 45402-2911.

(xii) Delaware, Fairfield, Fayette, Franklin, Knox, Licking, Madison, Morrow, Pickaway, and Union Counties; Ohio Environmental Protection Agency, Central District Office, Air Pollution control, 50 West Town Street, Suite 700, Columbus, Ohio 43215.

(xiii) Geauga and Lake Counties; Lake County General Health District, Air Pollution Control, 33 Mill Street, Painesville, OH 44077.

(xiv) Mahoning and Trumbull Counties; Mahoning-Trumbull Air Pollution Control Agency, 345 Oak Hill Avenue, Suite 200, Youngstown, OH 44502.

(LL) State of Oklahoma, Oklahoma State Department of Health, Air Quality Service, P.O. Box 53551, Oklahoma City, OK 73152.

(i) Oklahoma City and County: Director, Oklahoma City-County Health Department, 921 Northeast 23rd Street, Oklahoma City, OK 73105.

(ii) Tulsa County: Tulsa City-County Health Department, 4616 East Fifteenth Street, Tulsa, OK 74112.

(MM) State of Oregon. (i) Oregon Department of Environmental Quality (ODEQ), 811 SW Sixth Avenue, Portland, OR 97204-1390, http://www.deq.state.or.us.

(ii) Lane Regional Air Pollution Authority (LRAPA), 1010 Main Street, Springfield, Oregon 97477, http://www.lrapa.org.

(NN)(i) City of Philadelphia, Department of Public Health, Air Management Services, 321 University Avenue, Philadelphia, Pennsylvania 19104.

(ii) Commonwealth of Pennsylvania, Department of Environmental Protection, Bureau of Air Quality Control, P.O. Box 8468, 400 Market Street, Harrisburg, Pennsylvania 17105.

(iii) Allegheny County Health Department, Bureau of Environmental Quality, Division of Air Quality, 301 39th Street, Pittsburgh, Pennsylvania 15201.

(OO) State of Rhode Island, Division of Air and Hazardous Materials, Department of Environmental Management, 291 Promenade Street, Providence, RI 02908.

(PP) State of South Carolina: South Carolina Department of Health and Environmental Control, 2600 Bull Street, Columbia, South Carolina 29201.

(QQ) State of South Dakota, Air Quality Program, Department of Environment and Natural Resources, Joe Foss Building, 523 East Capitol, Pierre, SD 57501-3181.

Note: For a table listing Region VIII's NSPS delegation status, see paragragh (c) of this section.

(RR) State of Tennessee: Tennessee Department of Environment and Conservation, Division of Air Pollution Control, 401 Church Street, 9th Floor, L&C Annex, Nashville, Tennessee 37243-1531.

Knox County Air Quality Management—Department of Public Health, 140 Dameron Avenue, Knoxville, TN 37917.

Air Pollution Control Bureau, Metropolitan Health Department, 311 23rd Avenue North, Nashville, TN 37203.

Chattanooga-Hamilton County Air Pollution Control Bureau, 6125 Preservation Drive, Chattanooga, TN 37416.

Memphis-Shelby County Health Department—Air Pollution Control Program, 814 Jefferson Avenue, Memphis, TN 38105.

(SS) State of Texas, Texas Air Control Board, 6330 Highway 290 East, Austin, TX 78723.

(TT) State of Utah, Division of Air Quality, Department of Environmental Quality, P.O. Box 144820, Salt Lake City, UT 84114-4820.

Note: For a table listing Region VIII's NSPS delegation status, see paragraph (c) of this section.

(UU) State of Vermont, Air Pollution Control Division, Agency of Natural Resources, Building 3 South, 103 South Main Street, Waterbury, VT 05676.

(VV) Commonwealth of Virginia, Department of Environmental Quality, 629 East Main Street, Richmond, Virginia 23219.

(WW) State of Washington. (i) Washington State Department of Ecology (Ecology), P.O. Box 47600, Olympia, WA 98504-7600, http://www.ecy.wa.gov/

(ii) Benton Clean Air Authority (BCAA), 650 George Washington Way, Richland, WA 99352-4289, http://www.bcaa.net/

(iii) Northwest Air Pollution Control Authority (NWAPA), 1600 South Second St., Mount Vernon, WA 98273-5202, http://www.nwair.org/

(iv) Olympic Regional Clean Air Agency (ORCAA), 909 Sleater-Kinney Road S.E., Suite 1, Lacey, WA 98503-1128, http://www.orcaa.org/

(v) Puget Sound Clean Air Agency (PSCAA), 110 Union Street, Suite 500, Seattle, WA 98101-2038, http://www.pscleanair.org/

(vi) Spokane County Air Pollution Control Authority (SCAPCA), West 1101 College, Suite 403, Spokane, WA 99201, http://www.scapca.org/

(vii) Southwest Clean Air Agency (SWCAA), 1308 NE. 134th St., Vancouver, WA 98685-2747, http://www.swcleanair.org/

(viii) Yakima Regional Clean Air Authority (YRCAA), 6 South 2nd Street, Suite 1016, Yakima, WA 98901, http://co.yakima.wa.us/cleanair/default.htm

(ix) The following table lists the delegation status of the New Source Performance Standards for the State of Washington. An “X” indicates the subpart has been delegated, subject to all the conditions and limitations set forth in Federal law and the letters granting delegation. Some authorities cannot be delegated and are retained by EPA. Refer to the letters granting delegation for a discussion of these retained authorities. The dates noted at the end of the table indicate the effective dates of Federal rules that have been delegated. Authority for implementing and enforcing any amendments made to these rules after these effective dates are not delegated.

NSPS Subparts Delegated to Washington Air Agencies

Subpart1Washington
Ecology2BCAA3NWAPA4ORCAA5PSCAA6SCAPCA7SWCAA8YRCAA9
A   General ProvisionsXXXXXXXX
B   Adoption and Submittal of State Plans for Designated Facilities
C   Emission Guidelines and Compliance Times
Cb   Large Municipal Waste Combustors that are Constructed on or before September 20, 1994 (Emission Guidelines and Compliance Times)
Cc   Municipal Solid Waste Landfills (Emission Guidelines and Compliance Times)
Cd   Sulfuric Acid Production Units (Emission Guidelines and Compliance Times)
Ce   Hospital/Medical/Infectious Waste Incinerators (Emission Guidelines and Compliance Times)
D   Fossil-Fuel-Fired Steam Generators for which Construction is Commenced after August 17, 1971XXXXXXXX
Da   Electric Utility Steam Generating Units for which Construction is Commenced after September 18, 1978XXXXXXXX
Db   Industrial-Commercial-Institutional Steam Generating UnitsXXXXXXXX
Dc   Small Industrial-Commercial-Institutional Steam Generating UnitsXXXXXXXX
E   IncineratorsXXXXXXXX
Ea   Municipal Waste Combustors for which Construction is Commenced after December 20, 1989 and on or before September 20, 1994XXXXXXXX
Eb—Large Municipal Waste CombustorsXXXX
Ec—Hospital/Medical/Infectious Waste IncineratorsXXXXXX
F   Portland Cement PlantsXXXXXXXX
G   Nitric Acid PlantsXXXXXXXX
H   Sulfuric Acid PlantsXXXXXXXX
I   Hot Mix Asphalt FacilitiesXXXXXXXX
J   Petroleum RefineriesXXXXXXXX
K   Storage Vessels for Petroleum Liquids for which Construction, Reconstruction, or Modification Commenced after June 11, 1973 and prior to May 19, 1978XXXXXXXX
Ka   Storage Vessels for Petroleum Liquids for which Construction, Reconstruction, or Modification Commenced after May 18, 1978 and prior to July 23, 1984XXXXXXXX
Kb   VOC Liquid Storage Vessels (including Petroleum Liquid Storage Vessels) for which Construction, Reconstruction, or Modification Commenced after July 23, 1984XXXXXXXX
L   Secondary Lead SmeltersXXXXXXXX
M   Secondary Brass and Bronze Production PlantsXXXXXXXX
N   Primary Emissions from Basic Oxygen Process Furnaces for which Construction is Commenced after June 11, 1973XXXXXXXX
Na   Secondary Emissions from Basic Oxygen Process Steel-making Facilities for which Construction is Commenced after January 20, 1983XXXXXXXX
O   Sewage Treatment PlantsXXXXXXXX
P   Primary Copper SmeltersXXXXXXXX
Q   Primary Zinc SmeltersXXXXXXXX
R   Primary Lead SmeltersXXXXXXXX
S   Primary Aluminum Reduction Plants10X
T   Phosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsXXXXXXXX
U   Phosphate Fertilizer Industry: Superphosphoric Acid PlantsXXXXXXXX
V   Phosphate Fertilizer Industry: Diammonium Phosphate PlantsXXXXXXXX
W   Phosphate Fertilizer Industry: Triple Superphosphate PlantsXXXXXXXX
X   Phosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesXXXXXXXX
Y   Coal Preparation PlantsXXXXXXXX
Z   Ferroalloy Production FacilitiesXXXXXXXX
AA   Steel Plants: Electric Arc Furnaces Constructed after October 21, 1974 and on or before August 17, 1983XXXXXXXX
AAa   Steel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed after August 7, 1983XXXXXXXX
BB   Kraft Pulp Mills11X
CC   Glass Manufacturing PlantsXXXXXXXX
DD   Grain ElevatorsXXXXXXXX
EE   Surface Coating of Metal FurnitureXXXXXXXX
GG   Stationary Gas TurbinesXXXXXXXX
HH   Lime Manufacturing PlantsXXXXXXXX
KK   Lead-Acid Battery Manufacturing PlantsXXXXXXXX
LL   Metallic Mineral Processing PlantsXXXXXXXX
MM   Automobile and Light Duty Truck Surface Coating OperationsXXXXXXXX
NN   Phosphate Rock PlantsXXXXXXXX
PP   Ammonium Sulfate ManufactureXXXXXXXX
QQ   Graphic Arts Industry: Publication Rotogravure PrintingXXXXXXXX
RR   Pressure Sensitive Tape and Label Surface Coating StandardsXXXXXXXX
SS   Industrial Surface Coating: Large AppliancesXXXXXXXX
TT   Metal Coil Surface CoatingXXXXXXXX
UU   Asphalt Processing and Asphalt Roof ManufactureXXXXXXXX
VV   Equipment Leaks of VOC in Synthetic Organic Chemical Manufacturing IndustryXXXXXXXX
WW   Beverage Can Surface Coating IndustryXXXXXXXX
XX   Bulk Gasoline TerminalsXXXXXXXX
AAA   New Residential Wood Heaters
BBB   Rubber Tire Manufacturing IndustryXXXXXXXX
DDD   VOC Emissions from Polymer Manufacturing IndustryXXXXXXXX
FFF   Flexible Vinyl and Urethane Coating and PrintingXXXXXXXX
GGG   Equipment Leaks of VOC in Petroleum RefineriesXXXXXXXX
HHH   Synthetic Fiber Production FacilitiesXXXXXXXX
III   VOC Emissions from Synthetic Organic Chemical Manufacturing Industry Air Oxidation Unit ProcessesXXXXXXXX
JJJ   Petroleum Dry CleanersXXXXXXXX
KKK   Equipment Leaks of VOC from Onshore Natural Gas Processing PlantsXXXXXXXX
LLL   Onshore Natural Gas Processing: SO2 EmissionsXXXXXXXX
NNN   VOC Emissions from Synthetic Organic Chemical Manufacturing Industry Distillation OperationsXXXXXXXX
OOO   Nonmetallic Mineral Processing PlantsXXX
PPP   Wool Fiberglass Insulation Manufacturing PlantsXXXXXXXX
QQQ   VOC Emissions from Petroleum Refinery Wastewater SystemsXXXXXXXX
RRR   VOCs from Synthetic Organic Chemical Manufacturing Industry Reactor ProcessesXXXXXXXX
SSS   Magnetic Tape Coating FacilitiesXXXXXXXX
TTT   Industrial Surface Coating: Surface Coating of Plastic Parts for Business MachinesXXXXXXXX
UUU   Calciners and Dryers in Mineral IndustriesXXXXXXXX
VVV   Polymeric Coating of Supporting Substrates FacilitiesXXXXXXXX
WWW   Municipal Solid Waste LandfillsXXXXXXXX
AAAA   Small Municipal Waste Combustion Units for which Construction is Commenced after August 30, 1999 or for which Modification or Reconstruction is Commenced after June 6, 2001XXXXXX
BBBB   Small Municipal Waste Combustion Units Constructed on or before August 30, 1999 (Emission Guidelines and Compliance Times)
CCCC   Commercial and Industrial Solid Waste Incineration Units for which Construction is Commenced after November, 30, 1999 or for which Modification or Reconstruction is Commenced on or after June 1, 2001XXXXXX
DDDD   Commercial and Industrial Solid Waste Incineration Units that Commenced Construction on or before November 30, 1999 (Emission Guidelines and Compliance Times)

1Any authority within any subpart of this part that is not delegable, is not delegated. Please refer to Attachment B to the delegation letters for a listing of the NSPS authorities excluded from delegation.

2Washington State Department of Ecology, for 40 CFR 60.17(h)(1), (h)(2), (h)(3) and 40 CFR part 60, subpart AAAA, as in effect on June 6, 2001; for 40 CFR part 60, subpart CCCC, as in effect on June 1, 2001; and for all other NSPS delegated, as in effect February 20, 2001.

3Benton Clean Air Authority, for 40 CFR 60.17(h)(1), (h)(2), (h)(3) and 40 CFR part 60, subpart AAAA, as in effect on June 6, 2001; for 40 CFR part 60, subpart CCCC, as in effect on June 1, 2001; and for all other NSPS delegated, as in effect February 20, 2001.

4Northwest Air Pollution Authority, for all NSPS delegated, as in effect on July 1, 2000.

5Olympic Regional Clean Air Authority, for 40 CFR 60.17(h)(1), (h)(2), (h)(3) and 40 CFR part 60, subpart AAAA, as in effect on June 6, 2001; for 40 CFR part 60, subpart CCCC, as in effect on June 1, 2001; and for all other NSPS delegated, as in effect February 20, 2001.

6Puget Sound Clean Air Authority, for all NSPS delegated, as in effect on July 1, 2002.

7Spokane County Air Pollution Control Authority, for 40 CFR 60.17(h)(1), (h)(2), (h)(3) and 40 CFR part 60, subpart AAAA, as in effect on June 6, 2001; for 40 CFR part 60, subpart CCCC, as in effect on June 1, 2001; and for all other NSPS delegated, as in effect February 20, 2001.

8Southwest Clean Air Agency, for all NSPS delegated, as in effect on July 1, 2000.

9Yakima Regional Clean Air Authority, for 40 CFR 60.17(h)(1), (h)(2), (h)(3) and 40 CFR part 60, subpart AAAA, as in effect on June 6, 2001; for 40 CFR part 60, subpart CCCC, as in effect on June 1, 2001; and for all other NSPS delegated, as in effect February 20, 2001.

10Subpart S of this part is not delegated to local agencies in Washington because the Washington State Department of Ecology retains sole authority to regulate Primary Aluminum Plants, pursuant to Washington Administrative Code 173-415-010.

11Subpart BB of this part is not delegated to local agencies in Washington because the Washington State Department of Ecology retains sole authority to regulate Kraft and Sulfite Pulping Mills, pursuant to Washington State Administrative Code 173-405-012 and 173-410-012.

(XX) State of West Virginia, Department of Environmental Protection, Division of Air Quality, 601 57th Street, SE., Charleston, West Virginia 25304.

(YY) State of Wisconsin: Wisconsin Department of Natural Resouces, 101 South Webster St., P.O. Box 7921, Madison, Wisconsin 53707-7921.

(ZZ) State of Wyoming, Department of Environmental Quality, Air Quality Division, Herschler Building, 122 West 25th Street, Cheyenne, WY 82002.

Note: For a table listing Region VIII's NSPS delegation status, see paragraph (c) of this section.

(AAA) Territory of Guam: Guam Environmental Protection Agency, P.O. Box 22439 GMF, Barrigada, Guam 96921.

Note: For tables listing the delegation status of agencies in Region IX, see paragraph (d) of this section.

(BBB) Commonwealth of Puerto Rico: Commonwealth of Puerto Rico Environmental Quality Board, P.O. Box 11488, Santurce, PR 00910, Attention: Air Quality Area Director (see table under §60.4(b)(FF)(1)).

(CCC) U.S. Virgin Islands: U.S. Virgin Islands Department of Conservation and Cultural Affairs, P.O. Box 578, Charlotte Amalie, St. Thomas, VI 00801.

(DDD) American Samoa: American Samoa Environmental Protection Agency, P.O. Box PPA, Pago Pago, American Samoa 96799.

Note: For tables listing the delegation status of agencies in Region IX, see paragraph (d) of this section.

(EEE) Commonwealth of the Northern Mariana Islands: CNMI Division of Environmental Quality, P.O. Box 501304, Saipan, MP 96950.

Note: For tables listing the delegation status of agencies in Region IX, see paragraph (d) of this section.

(c) The following is a table indicating the delegation status of New Source Performance Standards for Region VIII.

Delegation Status of New Source Performance Standards

[(NSPS) for Region VIII]

SubpartCOMTNDSDUTWY
A—General Provisions(*)(*)(*)(*)(*)(*)
D—Fossil Fuel Fired Steam Generators(*)(*)(*)(*)(*)(*)
Da—Electric Utility Steam Generators(*)(*)(*)(*)(*)(*)
Db—Industrial-Commercial—Institutional Steam Generators(*)(*)(*)(*)(*)(*)
Dc—Industrial-Commercial-Institutional Steam Generators(*)(*)(*)(*)(*)(*)
E—Incinerators(*)(*)(*)(*)(*)(*)
Ea—Municipal Waste Combustors(*)(*)(*)(*)(*)(*)
Eb—Large Municipal Waste Combustors   (*)   (*)(*)(*)
Ec—Hospital/Medical/Infectious Waste Incinerators(*)(*)(*)(*)(*)(*)
F—Portland Cement Plants(*)(*)(*)(*)(*)(*)
G—Nitric Acid Plants(*)(*)(*)(*)(*)
H—Sulfuric Acid Plants(*)(*)(*)(*)(*)
I—Asphalt Concrete Plants(*)(*)(*)(*)(*)(*)
J—Petroleum Refineries(*)(*)(*)(*)(*)
K—Petroleum Storage Vessels (after 6/11/73 & prior to
   5/19/78)
(*)(*)(*)(*)(*)(*)
Ka—Petroleum Storage Vessels (after 5/18/78 & prior to
   7/23/84)
(*)(*)(*)(*)(*)(*)
Kb—Petroleum Storage Vessels (after 7/23/84)(*)(*)(*)(*)(*)(*)
L—Secondary Lead Smelters(*)(*)(*)(*)
M—Secondary Brass and Bronze Production
Plants(*)(*)(*)(*)
N—Primary Emissions from Basic Oxygen Process Furnaces (after 6/11/73)(*)(*)(*)(*)
Na—Secondary Emissions from Basic Oxygen Process Furnaces (after 1/20/83)(*)(*)(*)(*)
O—Sewage Treatment Plants(*)(*)(*)(*)(*)(*)
P—Primary Copper Smelters(*)(*)(*)(*)
Q—Primary Zinc Smelters(*)(*)(*)(*)
R—Primary Lead Smelters(*)(*)(*)(*)
S—Primary Aluminum Reduction Plants(*)(*)(*)(*)
T—Phosphate Fertilizer Industry: Wet Process Phosphoric Plants(*)(*)(*)(*)(*)
U—Phosphate Fertilizer Industry: Superphosphoric Acid Plants(*)(*)(*)(*)(*)
V—Phosphate Fertilizer Industry: Diammonium Phosphate Plants(*)(*)(*)(*)(*)
W—Phosphate Fertilizer Industry: Triple Superphosphate Plants(*)(*)(*)(*)(*)
X—Phosphate Fertilizer Industry: Granular Triple Superphosphate Storage Facilities(*)(*)(*)(*)(*)
Y—Coal Preparation Plants(*)(*)(*)(*)(*)(*)
Z—Ferroalloy Production Facilities(*)(*)(*)(*)(*)
AA—Steel Plants: Electric Arc Furnaces (10/21/74-8/17/83)(*)(*)(*)(*)(*)
AAa—Steel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels (after 8/7/83)(*)(*)(*)(*)(*)
BB—Kraft Pulp Mills(*)(*)(*)(*)
CC—Glass Manufacturing Plants(*)(*)(*)(*)(*)
DD—Grain Elevator(*)(*)(*)(*)(*)(*)
EE—Surface Coating of Metal Furniture(*)(*)(*)(*)(*)
GG—Stationary Gas Turbines(*)(*)(*)(*)(*)(*)
HH—Lime Manufacturing Plants(*)(*)(*)(*)(*)(*)
KK—Lead-Acid Battery Manufacturing Plants(*)(*)(*)(*)(*)
LL—Metallic Mineral Processing Plants(*)(*)(*)(*)(*)(*)
MM—Automobile & Light Duty Truck Surface Coating Operations(*)(*)(*)(*)(*)
NN—Phosphate Rock Plants(*)(*)(*)(*)(*)
PP—Ammonium Sulfate Manufacturing(*)(*)(*)(*)(*)
QQ—Graphic Arts Industry: Publication Rotogravure Printing(*)(*)(*)(*)(*)(*)
RR—Pressure Sensitive Tape & Label Surface Coating(*)(*)(*)(*)(*)(*)
SS—Industrial Surface Coating: Large Applications(*)(*)(*)(*)(*)
TT—Metal Coil Surface Coating(*)(*)(*)(*)(*)
UU—Asphalt Processing & Asphalt Roofing Manufacture(*)(*)(*)(*)(*)
VV—Synthetic Organic Chemicals Manufacturing: Equipment Leaks of VOC(*)(*)(*)(*)(*)(*)
WW—Beverage Can Surface Coating Industry(*)(*)(*)(*)(*)
XX—Bulk Gasoline Terminals(*)(*)(*)(*)(*)(*)
AAA—Residential Wood Heaters(*)(*)(*)(*)(*)(*)
BBB—Rubber Tires(*)(*)(*)(*)(*)
DDD—VOC Emissions from Polymer Manufacturing Industry(*)(*)(*)(*)(*)
FFF—Flexible Vinyl & Urethane Coating & Printing(*)(*)(*)(*)(*)
GGG—Equipment Leaks of VOC in Petroleum Refineries(*)(*)(*)(*)(*)
HHH—Synthetic Fiber Production(*)(*)(*)(*)(*)
III—VOC Emissions from the Synthetic Organic Chemical Manufacturing Industry Air Oxidation Unit Processes(*)(*)(*)(*)
JJJ—Petroleum Dry Cleaners(*)(*)(*)(*)(*)(*)
KKK—Equipment Leaks of VOC from Onshore Natural Gas Processing Plants(*)(*)(*)(*)(*)
LLL—Onshore Natural Gas Processing: SO2 Emissions(*)(*)(*)(*)(*)
NNN—VOC Emissions from the Synthetic Organic Chemical Manufacturing Industry Distillation Operations(*)(*)(*)(*)(*)(*)
OOO—Nonmetallic Mineral Processing Plants(*)(*)(*)(*)(*)(*)
PPP—Wool Fiberglass Insulation Manufacturing Plants(*)(*)(*)(*)(*)
QQQ—VOC Emissions from Petroleum Refinery Wastewater Systems(*)(*)(*)(*)(*)
RRR—VOC Emissions from Synthetic Organic Chemistry Manufacturing Industry (SOCMI) Reactor Processes(*)(*)(*)(*)(*)(*)
SSS—Magnetic Tape Industry(*)(*)(*)(*)(*)(*)
TTT—Plastic Parts for Business Machine Coatings(*)(*)(*)   (*)(*)
UUU—Calciners and Dryers in Mineral Industries(*)(*)(*)(*)(*)(*)
VVV—Polymeric Coating of Supporting Substrates(*)(*)(*)   (*)(*)
WWW—Municipal Solid Waste Landfills(*)(*)(*)(*)(*)(*)
AAAA—Small Municipal Waste Combustors(*)(*)(*)(*)
CCCC—Commercial and Industrial Solid Waste Incineration Units(*)(*)(*)(*)
EEEE—Other Solid Waste Incineration Units for Which Construction is Commenced After December 9, 2004, or for Which Modification or Reconstruction is Commenced On or After June 16, 2006(*)

(*) Indicates approval of State regulation.

(d) The following tables list the specific part 60 standards that have been delegated unchanged to the air pollution control agencies in Region IX. The (X) symbol is used to indicate each standard that has been delegated. The following provisions of this subpart are not delegated: §§60.4(b), 60.8(b), 60.9, 60.11(b), 60.11(e), 60.13(a), 60.13(d)(2), 60.13(g), 60.13(i).

(1) Arizona. The following table identifies delegations for Arizona:

Delegation Status for New Source Performance Standards for Arizona

  SubpartAir pollution control agency
Arizona
DEQ
Maricopa
County
Pima
County
Pinal
County
AGeneral ProvisionsXXXX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971XXXX
DaElectric Utility Steam Generating Units Constructed After September 18, 1978XXXX
DbIndustrial-Commercial-Institutional Steam Generating UnitsXXXX
DcSmall Industrial-Commercial-Institutional Steam Generating UnitsXXXX
EIncineratorsXXXX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994XXXX
EbLarge Municipal Waste Combustors Constructed After September 20, 1994XXX
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996XXX
FPortland Cement PlantsXXXX
GNitric Acid PlantsXXXX
GaNitric Acid Plants For Which Construction, Reconstruction or Modification Commenced After October 14, 2011
HSulfuric Acid PlantXXXX
IHot Mix Asphalt FacilitiesXXXX
JPetroleum RefineriesXXXX
JaPetroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007X
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978XXXX
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984XXXX
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984XXXX
LSecondary Lead SmeltersXXXX
MSecondary Brass and Bronze Production PlantsXXXX
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973XXXX
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983XXXX
OSewage Treatment PlantsXXXX
PPrimary Copper SmeltersXXXX
QPrimary Zinc SmeltersXXXX
RPrimary Lead SmeltersXXXX
SPrimary Aluminum Reduction PlantsXXXX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsXXXX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsXXXX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsXXXX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsXXXX
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesXXXX
YCoal Preparation and Processing PlantsXXXX
ZFerroalloy Production FacilitiesXXXX
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983XXXX
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983XXXX
BBKraft Pulp MillsXXXX
CCGlass Manufacturing PlantsXXXX
DDGrain ElevatorsXXXX
EESurface Coating of Metal FurnitureXXXX
FF(Reserved)
GGStationary Gas TurbinesXXXX
HHLime Manufacturing PlantsXXXX
KKLead-Acid Battery Manufacturing PlantsXXXX
LLMetallic Mineral Processing PlantsXXXX
MMAutomobile and Light Duty Trucks Surface Coating OperationsXXXX
NNPhosphate Rock PlantsXXXX
PPAmmonium Sulfate ManufactureXXXX
QQGraphic Arts Industry: Publication Rotogravure PrintingXXXX
RRPressure Sensitive Tape and Label Surface Coating OperationsXXXX
SSIndustrial Surface Coating: Large AppliancesXXXX
TTMetal Coil Surface CoatingXXXX
UUAsphalt Processing and Asphalt Roofing ManufactureXXXX
VVEquipment Leaks of VOC in the Synthetic Organic Industry Chemicals ManufacturingXXXX
VVaEquipment Leaks of VOC in the Synthetic Organic Industry for Which Construction, Reconstruction, or Chemicals Manufacturing Modification Commenced After November 7, 2006XX
WWBeverage Can Surface Coating IndustryXXXX
XXBulk Gasoline TerminalsXXXX
AAANew Residential Wood HeatersXXXX
BBBRubber Tire Manufacturing IndustryXXXX
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing IndustryXXXX
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and PrintingXXXX
GGGEquipment Leaks of VOC in Petroleum RefineriesXXXX
GGGaEquipment Leaks of VOC in Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006XX
HHHSynthetic Fiber Production FacilitiesXXXX
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit ProcessesXXXX
JJJPetroleum Dry CleanersXXXX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing PlantsXXXX
LLLOnshore Natural Gas Processing: SO2 EmissionsXXXX
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsXXXX
OOONonmetallic Mineral Processing PlantsXXXX
PPPWool Fiberglass Insulation Manufacturing PlantsXXXX
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsXXXX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor ProcessesXX
SSSMagnetic Tape Coating FacilitiesXXXX
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business MachinesXXXX
UUUCalciners and Dryers in Mineral IndustriesXXX
VVVPolymeric Coating of Supporting Substrates FacilitiesXXXX
WWWMunicipal Solid Waste LandfillsXXX
AAAASmall Municipal Waste Combustion Units for Which Construction is Commenced After August 30, 1999 or for Which Modification or Reconstruction is Commended After June 6, 2001XXX
CCCCCommercial and Industrial Solid Waste Incineration Units for Which Construction Is Commenced After November 30, 1999 or for Which Modification or Reconstruction Is Commenced on or After June 1, 2001XXX
EEEEOther Solid Waste Incineration Units for Which Construction is Commenced After December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006XX
GGGG(Reserved)
HHHH(Reserved)
IIIIStationary Compression Ignition Internal Combustion EnginesXX
JJJJStationary Spark Ignition Internal Combustion EnginesX
KKKKStationary Combustion TurbinesXX
LLLLNew Sewage Sludge Incineration Units
OOOOCrude Oil and Natural Gas Production, Transmission, and Distribution

(2) California. The following tables identify delegations for each of the local air pollution control agencies of California.

(i) Delegations for Amador County Air Pollution Control District, Antelope Valley Air Quality Management District, Bay Area Air Quality Management District, and Butte County Air Quality Management District are shown in the following table:

Delegation Status for New Source Performance Standards for Amador County APCD, Antelope Valley AQMD, Bay Area AQMD, and Butte County AQMD

  Subpart Air pollution control agency
Amador
County APCD
Antelope
Valley AQMD
Bay Area AQMDButte County AQMD
AGeneral ProvisionsX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971XX
DaElectric Utility Steam Generating Units Constructed After September 18, 1978XX
DbIndustrial-Commercial-Institutional Steam Generating UnitsXX
DcSmall Industrial-Commercial-Institutional Steam Generating UnitsXX
EIncineratorsXX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994XX
EbLarge Municipal Waste Combustors Constructed After September 20, 1994X
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996X
FPortland Cement PlantsXX
GNitric Acid PlantsXX
GaNitric Acid Plants For Which Construction, Reconstruction or Modification Commenced After October 14, 2011
HSulfuric Acid PlantXX
IHot Mix Asphalt FacilitiesXX
JPetroleum RefineriesXX
JaPetroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007X
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978XX
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984XX
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984XX
LSecondary Lead SmeltersXX
MSecondary Brass and Bronze Production PlantsXX
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973XX
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983XX
OSewage Treatment PlantsXX
PPrimary Copper SmeltersXX
QPrimary Zinc SmeltersXX
RPrimary Lead SmeltersXX
SPrimary Aluminum Reduction PlantsXX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsXX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsXX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsXX
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesXX
YCoal Preparation and Processing PlantsXX
ZFerroalloy Production FacilitiesXX
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983XX
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983XX
BBKraft Pulp MillsXX
CCGlass Manufacturing PlantsXX
DDGrain ElevatorsXX
EESurface Coating of Metal FurnitureXX
FF(Reserved)
GGStationary Gas TurbinesXX
HHLime Manufacturing PlantsXX
KKLead-Acid Battery Manufacturing PlantsXX
LLMetallic Mineral Processing PlantsXX
MMAutomobile and Light Duty Trucks Surface Coating OperationsXX
NNPhosphate Rock PlantsXX
PPAmmonium Sulfate ManufactureXX
QQGraphic Arts Industry: Publication Rotogravure PrintingXX
RRPressure Sensitive Tape and Label Surface Coating OperationsXX
SSIndustrial Surface Coating: Large AppliancesXX
TTMetal Coil Surface CoatingXX
UUAsphalt Processing and Asphalt Roofing ManufactureXX
VVEquipment Leaks of VOC in the Synthetic Organic Industry Chemicals ManufacturingXX
VVaEquipment Leaks of VOC in the Synthetic Organic Industry for Which Construction, Reconstruction, or Chemicals Manufacturing Modification Commenced After November 7, 2006X
WWBeverage Can Surface Coating IndustryXX
XXBulk Gasoline Terminals
AAANew Residential Wood HeatersXX
BBBRubber Tire Manufacturing IndustryXX
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing IndustryXX
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and PrintingXX
GGGEquipment Leaks of VOC in Petroleum RefineriesXX
GGGaEquipment Leaks of VOC in Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006X
HHHSynthetic Fiber Production FacilitiesXX
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit ProcessesX
JJJPetroleum Dry CleanersXX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing PlantsXX
LLLOnshore Natural Gas Processing: SO2 EmissionsX
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsXX
OOONonmetallic Mineral Processing PlantsXX
PPPWool Fiberglass Insulation Manufacturing PlantsXX
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor ProcessesX
SSSMagnetic Tape Coating FacilitiesXX
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business MachinesXX
UUUCalciners and Dryers in Mineral IndustriesXX
VVVPolymeric Coating of Supporting Substrates FacilitiesXX
WWWMunicipal Solid Waste LandfillsX
AAAASmall Municipal Waste Combustion Units for Which Construction is Commenced After August 30, 1999 or for Which Modification or Reconstruction is Commended After June 6, 2001X
CCCCCommercial and Industrial Solid Waste Incineration Units for Which Construction Is Commenced After November 30, 1999 or for Which Modification or Reconstruction Is Commenced on or After June 1, 2001X
EEEEOther Solid Waste Incineration Units for Which Construction is Commenced After December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006X
GGGG(Reserved)
HHHH(Reserved)
IIIIStationary Compression Ignition Internal Combustion EnginesX
JJJJStationary Spark Ignition Internal Combustion EnginesX
KKKKStationary Combustion TurbinesX
LLLLNew Sewage Sludge Incineration Units
OOOOCrude Oil and Natural Gas Production, Transmission, and Distribution

(ii) [Reserved]

(iii) Delegations for Glenn County Air Pollution Control District, Great Basin Unified Air Pollution Control District, Imperial County Air Pollution Control District, and Kern County Air Pollution Control District are shown in the following table:

Delegation Status for New Source Performance Standards for Glenn County APCD, Great Basin Unified APCD, Imperial County APCD, and Kern County APCD

  Subpart Air pollution control agency
Glenn
County APCD
Great Basin Unified APCD Imperial County APCD Kern County APCD
AGeneral ProvisionsXX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971XX
DaElectric Utility Steam Generating Units Constructed After September 18, 1978XX
DbIndustrial-Commercial-Institutional Steam Generating UnitsXX
DcSmall Industrial Steam Generating UnitsXX
EIncineratorsXX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994X
EbMunicipal Waste Combustors Constructed After September 20, 1994
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996
FPortland Cement PlantsXX
GNitric Acid PlantsXX
HSulfuric Acid PlantsX
IHot Mix Asphalt FacilitiesXX
JPetroleum RefineriesXX
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978XX
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984XX
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984XX
LSecondary Lead SmeltersXX
MSecondary Brass and Bronze Production PlantsXX
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973XX
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983XX
OSewage Treatment PlantsXX
PPrimary Copper SmeltersXX
QPrimary Zinc SmeltersXX
RPrimary Lead SmeltersXX
SPrimary Aluminum Reduction PlantsXX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsXX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsXX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsXX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsXX
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesXX
YCoal Preparation PlantsXX
ZFerroalloy Production FacilitiesXX
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983XX
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983XX
BBKraft pulp MillsXX
CCGlass Manufacturing PlantsXX
DDGrain ElevatorsXX
EESurface Coating of Metal FurnitureXX
FF(Reserved)
GGStationary Gas TurbinesXX
HHLime Manufacturing PlantsXX
KKLead-Acid Battery Manufacturing PlantsXX
LLMetallic Mineral Processing PlantsXX
MMAutomobile and Light Duty Trucks Surface Coating OperationsXX
NNPhosphate Rock PlantsXX
PPAmmonium Sulfate ManufactureXX
QQGraphic Arts Industry: Publication Rotogravure PrintingXX
RRPressure Sensitive Tape and Label Surface Coating OperationsXX
SSIndustrial Surface Coating: Large AppliancesXX
TTMetal Coil Surface CoatingXX
UUAsphalt Processing and Asphalt Roofing ManufactureXX
VVEquipment Leaks of VOC in the Synthetic Organic Chemicals Manufacturing IndustryXX
WWBeverage Can Surface Coating IndustryXX
XXBulk Gasoline Terminals
AAANew Residential Wool HeatersXX
BBBRubber Tire Manufacturing IndustryXX
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing IndustryXX
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and PrintingXX
GGGEquipment Leaks of VOC in Petroleum RefineriesXX
HHHSynthetic Fiber Production FacilitiesXX
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit ProcessesXX
JJJPetroleum Dry CleanersXX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing PlantsXX
LLLOnshore Natural Gas Processing: SO2 EmissionsX
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsXX
OOONonmetallic Mineral Processing PlantsXX
PPPWool Fiberglass Insulation Manufacturing PlantsXX
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsXX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor ProcessesX
SSSMagnetic Tape Coating FacilitiesXX
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business MachinesXX  
UUUCalciners and Dryers in Mineral IndustriesXX
VVVPolymeric Coating of Supporting Substrates FacilitiesXX
WWWMunicipal Solid Waste LandfillsX

(iv) Delegations for Lake County Air Quality Management District, Lassen County Air Pollution Control District, Mariposa County Air Pollution Control District, and Mendocino County Air Pollution Control District are shown in the following table:

Delegation Status for New Source Performance Standards for Lake County Air Quality Management District, Lassen County Air Pollution Control District, Mariposa County Air Pollution Control District, and Mendocino County Air Pollution Control District

  Subpart Air pollution control agency
Lake County AQMD Lassen County APCD Mariposa County AQMD Mendocino County AQMD
AGeneral ProvisionsXX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971XX
DaElectric Utility Steam Generating Units Constructed After September 18, 1978XX
DbIndustrial-Commercial-Institutional Steam Generating UnitsX
DcSmall Industrial Steam Generating UnitsXX
EIncineratorsXX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994XX
EbMunicipal Waste Combustors Constructed After September 20, 1994
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996
FPortland Cement PlantsXX
GNitric Acid PlantsXX
HSulfuric Acid PlantsXX
IHot Mix Asphalt FacilitiesXX
JPetroleum RefineriesXX
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978XX
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984XX
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984XX
LSecondary Lead SmeltersXX
MSecondary Brass and Bronze Production PlantsXX
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973XX
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983XX
OSewage Treatment PlantsXX
PPrimary Copper SmeltersXX
QPrimary Zinc SmeltersXX
RPrimary Lead SmeltersXX
SPrimary Aluminum Reduction PlantsXX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsXX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsXX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsXX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsXX
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesXX
YCoal Preparation PlantsXX
ZFerroalloy Production FacilitiesXX
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983XX
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983XX
BBKraft Pulp MillsXX
CCGlass Manufacturing PlantsXX
DDGrain ElevatorsXX
EESurface Coating of Metal FurnitureXX
FF(Reserved)
GGStationary Gas TurbinesXX
HHLime Manufacturing PlantsXX
KKLead-Acid Battery Manufacturing PlantsXX
LLMetallic Mineral Processing PlantsXX
MMAutomobile and Light Duty Trucks Surface Coating OperationsXX
NNPhosphate Rock PlantsXX
PPAmmonium Sulfate ManufactureXX
QQGraphic Arts Industry: Publication Rotogravure PrintingXX
RRPressure Sensitive Tape and Label Surface Coating OperationsXX
SSIndustrial Surface Coating: Large AppliancesXX
TTMetal Coil Surface CoatingXX
UUAsphalt Processing and Asphalt Roofing ManufactureXX
VVEquipment Leaks of VOC in the Synthetic Organic Chemicals Manufacturing IndustryXX
WWBeverage Can Surface Coating IndustryXX
XXBulk Gasoline Terminals
AAANew Residential Wool HeatersXX
BBBRubber Tire Manufacturing IndustryXX
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing IndustryXX
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and PrintingXX
GGGEquipment Leaks of VOC in Petroleum RefineriesXX
HHHSynthetic Fiber Production FacilitiesXX
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit ProcessesXX
JJJPetroleum Dry CleanersXX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing PlantsXX
LLLOnshore Natural Gas Processing: SO2 EmissionsXX
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsXX
OOONonmetallic Mineral Processing PlantsXX
PPPWool Fiberglass Insulation Manufacturing PlantsXX
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsXX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor ProcessesX
SSSMagnetic Tape Coating FacilitiesXX
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business Machines
UUUCalciners and Dryers in Mineral IndustriesXX
VVVPolymeric Coating of Supporting Substrates FacilitiesXX
WWWMunicipal Solid Waste LandfillsX

(v) Delegations for Modoc Air Pollution Control District, Mojave Desert Air Quality Management District, Monterey Bay Unified Air Pollution Control District and North Coast Unified Air Quality Management District are shown in the following table:

Delegation Status for New Source Performance Standards for Modoc County APCD, Mojave Desert AQMD, Monterey Bay Unified APCD, and North Coast Unified AQMD

  SubpartAir pollution control agency
Modoc County APCDMojave Desert AQMDMonterey Bay Unified APCDNorth Coast Unified AQMD
AGeneral ProvisionsXXXX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971XXXX
DaElectric Utility Steam Generating Units Constructed After September 18, 1978XXXX
DbIndustrial-Commercial-Institutional Steam Generating UnitsXXXX
DcSmall Industrial-Commercial-Institutional Steam Generating UnitsXX
EIncineratorsXXXX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994X
EbLarge Municipal Waste Combustors Constructed After September 20, 1994X
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996X
FPortland Cement PlantsXXXX
GNitric Acid PlantsXXXX
GaNitric Acid Plants For Which Construction, Reconstruction or Modification Commenced After October 14, 2011
HSulfuric Acid PlantXXXX
IHot Mix Asphalt FacilitiesXXXX
JPetroleum RefineriesXXXX
JaPetroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007X
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978XXXX
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984XXXX
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984XXXX
LSecondary Lead SmeltersXXXX
MSecondary Brass and Bronze Production PlantsXXXX
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973XXXX
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983XXXX
OSewage Treatment PlantsXXXX
PPrimary Copper SmeltersXXXX
QPrimary Zinc SmeltersXXXX
RPrimary Lead SmeltersXXXX
SPrimary Aluminum Reduction PlantsXXXX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsXXXX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsXXXX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsXXXX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsXXXX
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesXXXX
YCoal Preparation and Processing PlantsXXXX
ZFerroalloy Production FacilitiesXXXX
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983XXXX
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983XXXX
BBKraft Pulp MillsXXXX
CCGlass Manufacturing PlantsXXXX
DDGrain ElevatorsXXXX
EESurface Coating of Metal FurnitureXXXX
FF(Reserved)
GGStationary Gas TurbinesXXXX
HHLime Manufacturing PlantsXXXX
KKLead-Acid Battery Manufacturing PlantsXXXX
LLMetallic Mineral Processing PlantsXXXX
MMAutomobile and Light Duty Trucks Surface Coating OperationsXXXX
NNPhosphate Rock PlantsXXXX
PPAmmonium Sulfate ManufactureXXXX
QQGraphic Arts Industry: Publication Rotogravure PrintingXXXX
RRPressure Sensitive Tape and Label Surface Coating OperationsXXXX
SSIndustrial Surface Coating: Large AppliancesXXXX
TTMetal Coil Surface CoatingXXXX
UUAsphalt Processing and Asphalt Roofing ManufactureXXXX
VVEquipment Leaks of VOC in the Synthetic Organic Industry Chemicals ManufacturingXXXX
VVaEquipment Leaks of VOC in the Synthetic Organic Industry for Which Construction, Reconstruction, or Chemicals Manufacturing Modification Commenced After November 7, 2006X
WWBeverage Can Surface Coating IndustryXXXX
XXBulk Gasoline Terminals
AAANew Residential Wood HeatersXXXX
BBBRubber Tire Manufacturing IndustryXXXX
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing IndustryXXX
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and PrintingXXXX
GGGEquipment Leaks of VOC in Petroleum RefineriesXXXX
GGGaEquipment Leaks of VOC in Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006X
HHHSynthetic Fiber Production FacilitiesXXXX
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit ProcessesX
JJJPetroleum Dry CleanersXXXX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing PlantsXXXX
LLLOnshore Natural Gas Processing: SO2 EmissionsXXXX
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsXXX
OOONonmetallic Mineral Processing PlantsXXXX
PPPWool Fiberglass Insulation Manufacturing PlantsXXXX
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsXXXX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor ProcessesX
SSSMagnetic Tape Coating FacilitiesXXXX
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business MachinesXXXX
UUUCalciners and Dryers in Mineral IndustriesXX
VVVPolymeric Coating of Supporting Substrates FacilitiesXXX
WWWMunicipal Solid Waste LandfillsX
AAAASmall Municipal Waste Combustion Units for Which Construction is Commenced After August 30, 1999 or for Which Modification or Reconstruction is Commended After June 6, 2001X
CCCCCommercial and Industrial Solid Waste Incineration Units for Which Construction Is Commenced After November 30, 1999 or for Which Modification or Reconstruction Is Commenced on or After June 1, 2001X
EEEEOther Solid Waste Incineration Units for Which Construction is Commenced After December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006X
GGGG(Reserved)
HHHH(Reserved)
IIIIStationary Compression Ignition Internal Combustion EnginesX
JJJJStationary Spark Ignition Internal Combustion EnginesX
KKKKStationary Combustion TurbinesX
LLLLNew Sewage Sludge Incineration Units
OOOOCrude Oil and Natural Gas Production, Transmission, and Distribution

(vi) Delegations for Northern Sierra Air Quality Management District, Northern Sonoma County Air Pollution Control District, Placer County Air Pollution Control District, and Sacramento Metropolitan Air Quality Management District are shown in the following table:

Delegation Status for New Source Performance Standards for Northern Sierra Air Quality Management District, Northern Sonoma County Air Pollution Control District, Placer County Air Pollution Control District, and Sacramento Metropolitan Air Quality Management District

  Subpart Air pollution control agency
Northern Sierra AQMD Northern Sonoma County APCD Placer County APCD Sacramento Metropolitan AQMD
AGeneral ProvisionsXX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971XX
DaElectric Utility Steam Generating Units Constructed After September 18, 1978XX
DbIndustrial-Commercial-Institutional Steam Generating UnitsX
DcSmall Industrial Steam Generating UnitsX
EIncineratorsXX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994X
EbMunicipal Waste Combustors Constructed After September 20, 1994X
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996X
FPortland Cement PlantsXX
GNitric Acid PlantsXX
HSulfuric Acid PlantsXX
IHot Mix Asphalt FacilitiesXX
JPetroleum RefineriesXX
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978XX
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984XX
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984X
LSecondary Lead SmeltersXX
MSecondary Brass and Bronze Production PlantsXX
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973XX
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983X
OSewage Treatment PlantsXX
PPrimary Copper SmeltersXX
QPrimary Zinc SmeltersXX
RPrimary Lead SmeltersXX
SPrimary Aluminum Reduction PlantsXX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsXX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsXX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsXX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsXX
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesXX
YCoal Preparation PlantsXX
ZFerroalloy Production FacilitiesXX
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983XX
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983X
BBKraft pulp MillsXX
CCGlass Manufacturing PlantsXX
DDGrain ElevatorsXX
EESurface Coating of Metal FurnitureX
FF(Reserved)
GGStationary Gas TurbinesXX
HHLime Manufacturing PlantsXX
KKLead-Acid Battery Manufacturing PlantsX
LLMetallic Mineral Processing PlantsX
MMAutomobile and Light Duty Trucks Surface Coating OperationsXX
NNPhosphate Rock PlantsX
PPAmmonium Sulfate ManufactureXX
QQGraphic Arts Industry: Publication Rotogravure PrintingX
RRPressure Sensitive Tape and Label Surface Coating OperationsX
SSIndustrial Surface Coating: Large AppliancesX
TTMetal Coil Surface CoatingX
UUAsphalt Processing and Asphalt Roofing ManufactureX
VVEquipment Leaks of VOC in the Synthetic Organic Chemicals Manufacturing IndustryX
WWBeverage Can Surface Coating IndustryX
XXBulk Gasoline Terminals
AAANew Residential Wool HeatersX
BBBRubber Tire Manufacturing IndustryX
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing IndustryX
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and PrintingX
GGGEquipment Leaks of VOC in Petroleum RefineriesX
HHHSynthetic Fiber Production FacilitiesX
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit ProcessesX
JJJPetroleum Dry CleanersX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing PlantsX
LLLOnshore Natural Gas Processing: SO2 EmissionsX
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsX
OOONonmetallic Mineral Processing PlantsX
PPPWool Fiberglass Insulation Manufacturing PlantsX
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor ProcessesX
SSSMagnetic Tape Coating FacilitiesX
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business MachinesX
UUUCalciners and Dryers in Mineral IndustriesX
VVVPolymeric Coating of Supporting Substrates FacilitiesX
WWWMunicipal Solid Waste LandfillsX

(vii) Delegations for San Diego County Air Pollution Control District, San Joaquin Valley Unified Air Pollution Control District, San Luis Obispo County Air Pollution Control District, and Santa Barbara County Air Pollution Control District are shown in the following table:

Delegation Status for New Source Performance Standards for San Diego County APCD, San Joaquin Valley Unified APCD, San Luis Obispo County APCD, and Santa Barbara County APCD

  SubpartAir pollution control agency
San Diego County APCDSan Joaquin Valley Unified APCDSan Luis Obispo County APCDSanta Barbara County APCD
AGeneral ProvisionsXXXX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971XXXX
DaElectric Utility Steam Generating Units Constructed After September 18, 1978XXXX
DbIndustrial-Commercial-Institutional Steam Generating UnitsXXXX
DcSmall Industrial-Commercial-Institutional Steam Generating UnitsXXXX
EIncineratorsXXXX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994XXX
EbLarge Municipal Waste Combustors Constructed After September 20, 1994XXX
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996XX
FPortland Cement PlantsXXX
GNitric Acid PlantsXXX
GaNitric Acid Plants For Which Construction, Reconstruction or Modification Commenced After October 14, 2011
HSulfuric Acid PlantXXX
IHot Mix Asphalt FacilitiesXXXX
JPetroleum RefineriesXXXX
JaPetroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007X
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978XXXX
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984XXXX
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984XXXX
LSecondary Lead SmeltersXXXX
MSecondary Brass and Bronze Production PlantsXXXX
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973XXX
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983XXX
OSewage Treatment PlantsXXXX
PPrimary Copper SmeltersXXX
QPrimary Zinc SmeltersXXX
RPrimary Lead SmeltersXXX
SPrimary Aluminum Reduction PlantsXXX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsXXX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsXXX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsXXX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsXXX
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesXXX
YCoal Preparation and Processing PlantsXXX
ZFerroalloy Production FacilitiesXXX
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983XXX
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983XXX
BBKraft Pulp MillsXXX
CCGlass Manufacturing PlantsXXXX
DDGrain ElevatorsXXXX
EESurface Coating of Metal FurnitureXXX
FF(Reserved)
GGStationary Gas TurbinesXXXX
HHLime Manufacturing PlantsXXX
KKLead-Acid Battery Manufacturing PlantsXXX
LLMetallic Mineral Processing PlantsXXX
MMAutomobile and Light Duty Trucks Surface Coating OperationsXXX
NNPhosphate Rock PlantsXXX
PPAmmonium Sulfate ManufactureXXX
QQGraphic Arts Industry: Publication Rotogravure PrintingXXX
RRPressure Sensitive Tape and Label Surface Coating OperationsXXX
SSIndustrial Surface Coating: Large AppliancesXXX
TTMetal Coil Surface CoatingXXX
UUAsphalt Processing and Asphalt Roofing ManufactureXXX
VVEquipment Leaks of VOC in the Synthetic Organic Industry Chemicals ManufacturingXXX
VVaEquipment Leaks of VOC in the Synthetic Organic Industry for Which Construction, Reconstruction, or Chemicals Manufacturing Modification Commenced After November 7, 2006X
WWBeverage Can Surface Coating IndustryXXX
XXBulk Gasoline Terminals
AAANew Residential Wood HeatersXXXX
BBBRubber Tire Manufacturing IndustryXXX
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing IndustryXX
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and PrintingXXX
GGGEquipment Leaks of VOC in Petroleum RefineriesXXX
GGGaEquipment Leaks of VOC in Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006X
HHHSynthetic Fiber Production FacilitiesXXX
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit ProcessesXX
JJJPetroleum Dry CleanersXXX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing PlantsXXX
LLLOnshore Natural Gas Processing: SO2 EmissionsXXX
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsXX
OOONonmetallic Mineral Processing PlantsXXXX
PPPWool Fiberglass Insulation Manufacturing PlantsXXX
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsXXX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor ProcessesXXX
SSSMagnetic Tape Coating FacilitiesXXX
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business MachinesXXX
UUUCalciners and Dryers in Mineral IndustriesXXXX
VVVPolymeric Coating of Supporting Substrates FacilitiesXXXX
WWWMunicipal Solid Waste LandfillsXXXX
AAAASmall Municipal Waste Combustion Units for Which Construction is Commenced After August 30, 1999 or for Which Modification or Reconstruction is Commended After June 6, 2001XX
CCCCCommercial and Industrial Solid Waste Incineration Units for Which Construction Is Commenced After November 30, 1999 or for Which Modification or Reconstruction Is Commenced on or After June 1, 2001XX
EEEEOther Solid Waste Incineration Units for Which Construction is Commenced After December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006XX
GGGG(Reserved)
HHHH(Reserved)
IIIIStationary Compression Ignition Internal Combustion EnginesX
JJJJStationary Spark Ignition Internal Combustion EnginesX
KKKKStationary Combustion TurbinesXX
LLLLNew Sewage Sludge Incineration Units
OOOOCrude Oil and Natural Gas Production, Transmission, and Distribution

(viii) Delegations for Shasta County Air Quality Management District, Siskiyou County Air Pollution Control District, South Coast Air Quality Management District, and Tehama County Air Pollution Control District are shown in the following table:

Delegation Status for New Source Performance Standards for Shasta County AQMD, Siskiyou County APCD, South Coast AQMD, and Tehama County APCD

  SubpartAir pollution control agency
Shasta County AQMDSiskiyou County APCDSouth Coast AQMDTehama
County APCD
AGeneral ProvisionsXXX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971XX
DaElectric Utility Steam Generating Units Constructed After September 18, 1978X
DbIndustrial-Commercial-Institutional Steam Generating UnitsX
DcSmall Industrial-Commercial-Institutional Steam Generating UnitsX
EIncineratorsXX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994X
EbLarge Municipal Waste Combustors Constructed After September 20, 1994X
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996X
FPortland Cement PlantsXX
GNitric Acid PlantsXX
GaNitric Acid Plants For Which Construction, Reconstruction or Modification Commenced After October 14, 2011
HSulfuric Acid PlantXX
IHot Mix Asphalt FacilitiesXX
JPetroleum RefineriesXX
JaPetroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007X
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978XX
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984X
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984X
LSecondary Lead SmeltersXX
MSecondary Brass and Bronze Production PlantsXX
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973XX
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983X
OSewage Treatment PlantsXX
PPrimary Copper SmeltersXX
QPrimary Zinc SmeltersXX
RPrimary Lead SmeltersXX
SPrimary Aluminum Reduction PlantsXX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsXX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsXX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsXX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsXX
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesXX
YCoal Preparation and Processing PlantsXX
ZFerroalloy Production FacilitiesXX
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983XX
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983X
BBKraft Pulp MillsXX
CCGlass Manufacturing PlantsX
DDGrain ElevatorsXX
EESurface Coating of Metal FurnitureX
FF(Reserved)
GGStationary Gas TurbinesX
HHLime Manufacturing PlantsXX
KKLead-Acid Battery Manufacturing PlantsX
LLMetallic Mineral Processing PlantsX
MMAutomobile and Light Duty Trucks Surface Coating OperationsX
NNPhosphate Rock PlantsX
PPAmmonium Sulfate ManufactureX
QQGraphic Arts Industry: Publication Rotogravure PrintingX
RRPressure Sensitive Tape and Label Surface Coating OperationsX
SSIndustrial Surface Coating: Large AppliancesX
TTMetal Coil Surface CoatingX
UUAsphalt Processing and Asphalt Roofing ManufactureX
VVEquipment Leaks of VOC in the Synthetic Organic Industry Chemicals ManufacturingX
VVaEquipment Leaks of VOC in the Synthetic Organic Industry for Which Construction, Reconstruction, or Chemicals Manufacturing Modification Commenced After November 7, 2006X
WWBeverage Can Surface Coating IndustryX
XXBulk Gasoline Terminals
AAANew Residential Wood HeatersXX
BBBRubber Tire Manufacturing IndustryXX
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing IndustryX
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and PrintingX
GGGEquipment Leaks of VOC in Petroleum RefineriesX
GGGaEquipment Leaks of VOC in Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006X
HHHSynthetic Fiber Production FacilitiesX
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit ProcessesX
JJJPetroleum Dry CleanersX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing PlantsX
LLLOnshore Natural Gas Processing: SO2 EmissionsX
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsX
OOONonmetallic Mineral Processing PlantsX
PPPWool Fiberglass Insulation Manufacturing PlantsX
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsXX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor ProcessesX
SSSMagnetic Tape Coating FacilitiesXX
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business MachinesXX
UUUCalciners and Dryers in Mineral IndustriesX
VVVPolymeric Coating of Supporting Substrates FacilitiesX
WWWMunicipal Solid Waste LandfillsX
AAAASmall Municipal Waste Combustion Units for Which Construction is Commenced After August 30, 1999 or for Which Modification or Reconstruction is Commended After June 6, 2001XXX
CCCCCommercial and Industrial Solid Waste Incineration Units for Which Construction Is Commenced After November 30, 1999 or for Which Modification or Reconstruction Is Commenced on or After June 1, 2001X
EEEEOther Solid Waste Incineration Units for Which Construction is Commenced After December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006X
GGGG(Reserved)
HHHH(Reserved)
IIIIStationary Compression Ignition Internal Combustion EnginesX
JJJJStationary Spark Ignition Internal Combustion EnginesX
KKKKStationary Combustion TurbinesX
LLLLNew Sewage Sludge Incineration Units
OOOOCrude Oil and Natural Gas Production, Transmission, and Distribution

(ix) Delegations for Tuolumne County Air Pollution Control District, Ventura County Air Pollution Control District, and Yolo-Solano Air Quality Management District are shown in the following table:

Delegation Status for New Source Performance Standards for Tuolumne County Air Pollution Control District, Ventura County Air Pollution Control District, and Yolo-Solano Air Quality Management District

  SubpartAir Pollution Control Agency
Tuolumne County APCDVentura County APCDYolo-Solano AQMD
AGeneral ProvisionsXX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971XX
DaElectric Utility Steam Generating Units Constructed After September 18, 1978X
DbIndustrial-Commercial-Institutional Steam Generating UnitsXX
DcSmall Industrial Steam Generating UnitsX
EIncineratorsX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994X
EbMunicipal Waste Combustors Constructed After September 20, 1994X
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996X
FPortland Cement PlantsX
GNitric Acid PlantsX
HSulfuric Acid PlantsX
IHot Mix Asphalt FacilitiesXX
JPetroleum RefineriesXX
JaPetroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978XX
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984X
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984X
LSecondary Lead SmeltersX
MSecondary Brass and Bronze Production PlantsX
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973X
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983X
OSewage Treatment PlantsX
PPrimary Copper SmeltersX
QPrimary Zinc SmeltersX
RPrimary Lead SmeltersX
SPrimary Aluminum Reduction PlantsX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsX
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesX
YCoal Preparation PlantsX
ZFerroalloy Production FacilitiesX
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983XX
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983X
BBKraft pulp MillsX
CCGlass Manufacturing PlantsX
DDGrain ElevatorsX
EESurface Coating of Metal FurnitureX
FF(Reserved)
GGStationary Gas TurbinesX
HHLime Manufacturing PlantsX
KKLead-Acid Battery Manufacturing PlantsX
LLMetallic Mineral Processing PlantsX
MMAutomobile and Light Duty Trucks Surface Coating OperationsX
NNPhosphate Rock PlantsX
PPAmmonium Sulfate ManufactureX
QQGraphic Arts Industry: Publication Rotogravure PrintingX
RRPressure Sensitive Tape and Label Surface Coating OperationsX
SSIndustrial Surface Coating: Large AppliancesX
TTMetal Coil Surface CoatingX
UUAsphalt Processing and Asphalt Roofing ManufactureX
VVEquipment Leaks of VOC in the Synthetic Organic Chemicals Manufacturing IndustryX
VVaEquipment Leaks of VOC in the Synthetic Organic Chemicals Manufacturing Industry for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006
WWBeverage Can Surface Coating IndustryX
XXBulk Gasoline Terminals
AAANew Residential Wood HeatersX
BBBRubber Tire Manufacturing IndustryX
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing IndustryX
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and PrintingX
GGGEquipment Leaks of VOC in Petroleum RefineriesX
GGGaEquipment Leaks of VOC in Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006
HHHSynthetic Fiber Production FacilitiesX
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit ProcessesX
JJJPetroleum Dry CleanersX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing PlantsX
LLLOnshore Natural Gas Processing: SO2 EmissionsX
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsX
OOONonmetallic Mineral Processing PlantsXX
PPPWool Fiberglass Insulation Manufacturing PlantsX
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor ProcessesX
SSSMagnetic Tape Coating FacilitiesX
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business MachinesX
UUUCalciners and Dryers in Mineral IndustriesX
VVVPolymeric Coating of Supporting Substrates FacilitiesX
WWWMunicipal Solid Waste LandfillsXX
AAAASmall Municipal Waste Combustion Units for Which Construction is Commenced After August 30, 1999 or for Which Modification or Reconstruction is Commenced After June 6, 2001X
CCCCCommercial and Industrial Solid Waste Incineration Units for Which Construction Is Commenced After November 30, 1999 or for Which Modification or Reconstruction Is Commenced on or After June 1, 2001X
EEEEOther Solid Waste Incineration Units for Which Construction is Commenced After December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006
GGGG(Reserved)
IIIIStationary Compression Ignition Internal Combustion Engines
JJJJStationary Spark Ignition Internal Combustion Engines
KKKKStationary Combustion Turbines

(3) Hawaii. The following table identifies delegations for Hawaii:

Delegation Status for New Source Performance Standards for Hawaii:

Delegation Status for New Source Performance Standards for Hawaii

  SubpartHawaii
AGeneral ProvisionsX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971X
DaElectric Utility Steam Generating Units Constructed After September 18, 1978X
DbIndustrial-Commercial-Institutional Steam Generating UnitsX
DcSmall Industrial Steam Generating UnitsX
EIncineratorsX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994X
EbMunicipal Waste Combustors Constructed After September 20, 1994X
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996X
FPortland Cement PlantsX
GNitric Acid Plants
HSulfuric Acid Plants
IHot Mix Asphalt FacilitiesX
JPetroleum RefineriesX
JaPetroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978X
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984X
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984X
LSecondary Lead Smelters
MSecondary Brass and Bronze Production Plants
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983
OSewage Treatment PlantsX
PPrimary Copper Smelters
QPrimary Zinc Smelters
RPrimary Lead Smelters
SPrimary Aluminum Reduction Plants
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid Plants
UPhosphate Fertilizer Industry: Superphosphoric Acid Plants
VPhosphate Fertilizer Industry: Diammonium Phosphate Plants
WPhosphate Fertilizer Industry: Triple Superphosphate Plants
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage Facilities
YCoal Preparation PlantsX
ZFerroalloy Production Facilities
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983X
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983X
BBKraft pulp Mills
CCGlass Manufacturing Plants
DDGrain Elevators
EESurface Coating of Metal Furniture
FF(Reserved)
GGStationary Gas TurbinesX
HHLime Manufacturing Plants
KKLead-Acid Battery Manufacturing Plants
LLMetallic Mineral Processing Plants
MMAutomobile and Light Duty Trucks Surface Coating Operations
NNPhosphate Rock Plants
PPAmmonium Sulfate Manufacture
QQGraphic Arts Industry: Publication Rotogravure Printing
RRPressure Sensitive Tape and Label Surface Coating Operations
SSIndustrial Surface Coating: Large Appliances
TTMetal Coil Surface Coating
UUAsphalt Processing and Asphalt Roofing Manufacture
VVEquipment Leaks of VOC in the Synthetic Organic Chemicals Manufacturing IndustryX
VVaEquipment Leaks of VOC in the Synthetic Organic Chemicals Manufacturing Industry for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006
WWBeverage Can Surface Coating IndustryX
XXBulk Gasoline TerminalsX
AAANew Residential Wool Heaters
BBBRubber Tire Manufacturing Industry
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing Industry
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and Printing
GGGEquipment Leaks of VOC in Petroleum RefineriesX
GGGaEquipment Leaks of VOC in Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006
HHHSynthetic Fiber Production Facilities
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit Processes
JJJPetroleum Dry CleanersX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing Plants
LLLOnshore Natural Gas Processing: SO2 Emissions
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsX
OOONonmetallic Mineral Processing PlantsX
PPPWool Fiberglass Insulation Manufacturing Plants
QQQVOC Emissions From Petroleum Refinery WastewaterX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor Processes
SSSMagnetic Tape Coating Facilities
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business Machines
UUUCalciners and Dryers in Mineral IndustriesX
VVVPolymeric Coating of Supporting Substrates FacilitiesX
WWWMunicipal Solid Waste LandfillsX
AAAASmall Municipal Waste Combustion Units for Which Construction is Commenced After August 30, 1999 or for Which Modification or Reconstruction is Commenced After June 6, 2001X
CCCCCommercial and Industrial Solid Waste Incineration Units for Which Construction Is Commenced After November 30, 1999 or for Which Modification or Reconstruction Is Commenced on or After June 1, 2001X
EEEEOther Solid Waste Incineration Units for Which Construction is Commenced After December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006
GGGG(Reserved)
IIIIStationary Compression Ignition Internal Combustion Engines
JJJJStationary Spark Ignition Internal Combustion Engines
KKKKStationary Combustion Turbines

(4) Nevada. The following table identifies delegations for Nevada:

Delegation Status for New Source Performance Standards for Nevada

  SubpartAir pollution control agency
Nevada DEPClark CountyWashoe
County
AGeneral ProvisionsXXX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971XXX
DaElectric Utility Steam Generating Units Constructed After September 18, 1978XX
DbIndustrial-Commercial-Institutional Steam Generating UnitsXX
DcSmall Industrial-Commercial-Institutional Steam Generating UnitsXX
EIncineratorsXXX
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994XX
EbLarge Municipal Waste Combustors Constructed After September 20, 1994XX
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996XX
FPortland Cement PlantsXXX
GNitric Acid PlantsXX
GaNitric Acid Plants For Which Construction, Reconstruction or Modification Commenced After October 14, 2011
HSulfuric Acid PlantXX
IHot Mix Asphalt FacilitiesXXX
JPetroleum RefineriesXX
JaPetroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978XXX
KaStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After May 18, 1978, and Prior to July 23, 1984XXX
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984XX
LSecondary Lead SmeltersXXX
MSecondary Brass and Bronze Production PlantsXX
NPrimary Emissions from Basic Oxygen Process Furnaces for Which Construction is Commenced After June 11, 1973XX
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities for Which Construction is Commenced After January 20, 1983XX
OSewage Treatment PlantsXXX
PPrimary Copper SmeltersXXX
QPrimary Zinc SmeltersXXX
RPrimary Lead SmeltersXXX
SPrimary Aluminum Reduction PlantsXX
TPhosphate Fertilizer Industry: Wet Process Phosphoric Acid PlantsXX
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsXX
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsXX
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsXX
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesXX
YCoal Preparation and Processing PlantsXXX
ZFerroalloy Production FacilitiesXX
AASteel Plants: Electric Arc Furnaces Constructed After October 21, 1974 and On or Before August 17, 1983XX
AAaSteel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed After August 7, 1983XX
BBKraft Pulp MillsXX
CCGlass Manufacturing PlantsXX
DDGrain ElevatorsXXX
EESurface Coating of Metal FurnitureXXX
FF(Reserved)
GGStationary Gas TurbinesXXX
HHLime Manufacturing PlantsXXX
KKLead-Acid Battery Manufacturing PlantsXXX
LLMetallic Mineral Processing PlantsXXX
MMAutomobile and Light Duty Trucks Surface Coating OperationsXXX
NNPhosphate Rock PlantsXXX
PPAmmonium Sulfate ManufactureXX
QQGraphic Arts Industry: Publication Rotogravure PrintingXXX
RRPressure Sensitive Tape and Label Surface Coating OperationsXX
SSIndustrial Surface Coating: Large AppliancesXXX
TTMetal Coil Surface CoatingXXX
UUAsphalt Processing and Asphalt Roofing ManufactureXXX
VVEquipment Leaks of VOC in the Synthetic Organic Industry Chemicals ManufacturingXXX
VVaEquipment Leaks of VOC in the Synthetic Organic Industry for Which Construction, Reconstruction, or Chemicals Manufacturing Modification Commenced After November 7, 2006XX
WWBeverage Can Surface Coating IndustryXX
XXBulk Gasoline TerminalsXX
AAANew Residential Wood HeatersX
BBBRubber Tire Manufacturing IndustryXX
CCC(Reserved)
DDDVolatile Organic Compounds (VOC) Emissions from the Polymer Manufacturing IndustryXX
EEE(Reserved)
FFFFlexible Vinyl and Urethane Coating and PrintingXX
GGGEquipment Leaks of VOC in Petroleum RefineriesXX
GGGaEquipment Leaks of VOC in Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After November 7, 2006XX
HHHSynthetic Fiber Production FacilitiesXX
IIIVolatile Organic Compound (VOC) Emissions From the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit ProcessesXX
JJJPetroleum Dry CleanersXXX
KKKEquipment Leaks of VOC From Onshore Natural Gas Processing PlantsXX
LLLOnshore Natural Gas Processing: SO2 EmissionsXX
MMM(Reserved)
NNNVolatile Organic Compound (VOC) Emissions From Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation OperationsXX
OOONonmetallic Mineral Processing PlantsXX
PPPWool Fiberglass Insulation Manufacturing PlantsXX
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsXX
RRRVolatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor ProcessesXX
SSSMagnetic Tape Coating FacilitiesXX
TTTIndustrial Surface Coating: Surface Coating of Plastic Parts for Business MachinesXXX
UUUCalciners and Dryers in Mineral IndustriesXXX
VVVPolymeric Coating of Supporting Substrates FacilitiesXXX
WWWMunicipal Solid Waste LandfillsXXX
AAAASmall Municipal Waste Combustion Units for Which Construction is Commenced After August 30, 1999 or for Which Modification or Reconstruction is Commended After June 6, 2001XXX
CCCCCommercial and Industrial Solid Waste Incineration Units for Which Construction Is Commenced After November 30, 1999 or for Which Modification or Reconstruction Is Commenced on or After June 1, 2001XXX
EEEEOther Solid Waste Incineration Units for Which Construction is Commenced After December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006XXX
GGGG(Reserved)
HHHH(Reserved)
IIIIStationary Compression Ignition Internal Combustion EnginesXXX
JJJJStationary Spark Ignition Internal Combustion EnginesXXX
KKKKStationary Combustion TurbinesXXX
LLLLNew Sewage Sludge Incineration UnitsX
OOOOCrude Oil and Natural Gas Production, Transmission, and Distribution

(5) Guam. The following table identifies delegations as of June 15, 2001:

Delegation Status for New Source Performance Standards for Guam

  Subpart Guam
AGeneral ProvisionsX
DFossil-Fuel Fired Steam Generators Constructed After August 17, 1971X
DaElectric Utility Steam Generating Units Constructed After September 18, 1978
DbIndustrial-Commercial-Institutional Steam Generating Units
DcSmall Industrial Steam Generating Units
EIncinerators
EaMunicipal Waste Combustors Constructed After December 20, 1989 and On or Before September 20, 1994
EbMunicipal Waste Combustors Constructed After September 20, 1994
EcHospital/Medical/Infectious Waste Incinerators for Which Construction is Commenced After June 20, 1996
FPortland Cement PlantsX
GNitric Acid Plants
HSulfuric Acid Plants
IHot Mix Asphalt FacilitiesX
JPetroleum RefineriesX
KStorage Vessels for Petroleum Liquids for Which Construction, Reconstruction, or Modification Commenced After June 11, 1973, and Prior to May 19, 1978X

(e) The following lists the specific part 60 standards that have been delegated unchanged to the air pollution control agencies in Region 6.

(1) New Mexico. The New Mexico Environment Department has been delegated all part 60 standards promulgated by EPA, except subpart AAA—Standards of Performance for New Residential Wood Heaters, as amended in the Federal Register through September 1, 2002.

(2) Louisiana. The Louisiana Department of Environmental Quality has been delegated all part 60 standards promulgated by EPA, except subpart AAA—Standards for Performance for New Residential Wood Heaters, as amended in the Federal Register through July 1, 2008.

Delegation Status for Part 60 Standards—State of Louisiana

SubpartSource categoryLDEQ1
AGeneral ProvisionsYes.
DFossil Fueled Steam Generators (>250 MM BTU/hr). Including amendments issued January 28, 2009. (74 FR 5072)Yes.
DaElectric Utility Steam Generating Units (>250 MM BTU/hr). Including amendments issued January 28, 2009. (74 FR 5072)Yes.
DbIndustrial-Commercial-Institutional Steam Generating Units (100 to 250 MM BTU/hr). Including amendments issued January 28, 2009. (74 FR 5072)Yes.
DcIndustrial-Commercial-Institutional Small Steam Generating Units (10 to 100 MM BTU/hr). Including amendments issued January 28, 2009. (74 FR 5072)Yes.
EIncinerators (>50 tons per day). Including amendments issued January 28, 2009. (74 FR 5072)Yes.
EaMunicipal Waste CombustorsYes.
EbLarge Municipal Waste CombustorsYes.
EcHospital/Medical/Infectious Waste IncineratorsYes.
FPortland Cement PlantsYes.
GNitric Acid PlantsYes.
HSulfuric Acid PlantsYes.
IHot Mix Asphalt FacilitiesYes.
JPetroleum RefineriesYes.
JaPetroleum Refineries (After May 14, 2007). Including amendments issued July 28, 2008. (73 FR 43626)Yes.
KStorage Vessels for Petroleum Liquids (After 6/11/73 & Before 5/19/78)Yes.
KaStorage Vessels for Petroleum Liquids (After 6/11/73 & Before 5/19/78)Yes.
KbVolatile Organic Liquid Storage Vessels (Including Petroleum Liquid Stg/Vessels) After 7/23/84Yes.
LSecondary Lead SmeltersYes.
MSecondary Brass and Bronze Production PlantsYes.
NPrimary Emissions from Basic Oxygen Process Furnaces (Construction Commenced After June 11, 1973)Yes.
NaSecondary Emissions from Basic Oxygen Process Steelmaking Facilities Construction is Commenced After January 20, 1983Yes.
OSewage Treatment PlantsYes.
PPrimary Copper SmeltersYes.
QPrimary Zinc SmeltersYes.
RPrimary Lead SmeltersYes.
SPrimary Aluminum Reduction PlantsYes.
TPhosphate Fertilizer Industry: Wet Process Phosphoric PlantsYes.
UPhosphate Fertilizer Industry: Superphosphoric Acid PlantsYes.
VPhosphate Fertilizer Industry: Diammonium Phosphate PlantsYes.
WPhosphate Fertilizer Industry: Triple Superphosphate PlantsYes.
XPhosphate Fertilizer Industry: Granular Triple Superphosphate Storage FacilitiesYes.
YCoal Preparation PlantsYes.
ZFerroalloy Production FacilitiesYes.
AASteel Plants: Electric Arc Furnaces After 10/21/74 & On or Before 8/17/83Yes.
AAaSteel Plants: Electric Arc Furnaces & Argon-Oxygen Decarburization Vessels After 8/07/83Yes.
BBKraft Pulp MillsYes.
CCGlass Manufacturing PlantsYes.
DDGrain ElevatorsYes.
EESurface Coating of Metal FurnatureYes.
GGStationary Gas TurbinesYes.
HHLime Manufacturing PlantsYes.
KKLead-Acid Battery Manufacturing PlantsYes.
LLMetallic Mineral Processing PlantsYes.
MMAutomobile & Light Duty Truck Surface Coating OperationsYes.
NNPhosphate Manufacturing PlantsYes.
PPAmmonium Sulfate ManufactureYes.
QQGraphic Arts Industry: Publication Rotogravure PrintingYes.
RRPressure Sensitive Tape and Label Surface Coating OperationsYes.
SSIndustrial Surface Coating: Large AppliancesYes.
TTMetal Coil Surface CoatingYes.
UUAsphalt Processing and Asphalt Roofing ManufactureYes.
VVVOC Equipment Leaks in the SOCMI IndustryYes.
VVaVOC Equipment Leaks in the SOCMI Industry (After November 7, 2006)Yes.
XXBulk Gasoline TerminalsYes.
AAANew Residential Wood HeatersNo
BBBRubber Tire Manufacturing IndustryYes.
DDDVolatile Organic Compound (VOC) Emissions from the Polymer Manufacturing IndustryYes.
FFFFlexible Vinyl and Urethane Coating and PrintingYes.
GGGVOC Equipment Leaks in Petroleum RefineriesYes.
HHHSynthetic Fiber ProductionYes.
IIIVOC Emissions from the SOCMI Air Oxidation Unit ProcessesYes.
JJJPetroleum Dry CleanersYes.
KKKVOC Equipment Leaks From Onshore Natural Gas Processing PlantsYes.
LLLOnshore Natural Gas Processing: SO2 EmissionsYes.
NNNVOC Emissions from SOCMI Distillation OperationsYes.
OOONonmetallic Mineral Processing PlantsYes.
PPPWool Fiberglass Insulation Manufacturing PlantsYes.
QQQVOC Emissions From Petroleum Refinery Wastewater SystemsYes.
RRRVOC Emissions from SOCMI Reactor ProcessesYes.
SSSMagnetic Tape Coating OperationsYes.
TTTIndustrial Surface Coating: Plastic Parts for Business MachinesYes.
UUUCalciners and Dryers in Mineral IndustriesYes.
VVVPolymeric Coating of Supporting Substrates FacilitiesYes.
WWWMunicipal Solid Waste LandfillsYes.
AAAASmall Municipal Waste Combustion Units (Construction is Commenced After 8/30/99 or Modification/Reconstruction is Commenced After 6/06/2001)Yes.
CCCCCommercial & Industrial Solid Waste Incineration Units (Construction is Commenced After 11/30/1999 or Modification/Reconstruction is Commenced on or After 6/01/2001)Yes.
EEEEOther Solid Waste Incineration Units (Constructed after 12/09/2004 or Modicatation/Reconstruction is commenced on or after 06/16/2004)Yes.
IIIIStationary Compression Ignition Internal Combustion EnginesYes.
JJJJStationary Spark Ignition Internal Combustion Engines. Including amendments issued October 8, 2008. (73 FR 59175)Yes.
KKKKStationary Combustion Turbines (Construction Commenced After 02/18/2005)Yes

1The Louisiana Department of Environmental Quality (LDEQ) has been delegated all Part 60 standards promulgated by EPA, except subpart AAA—Standards of Performance for New Residential Wood Heaters—as amended in the Federal Register through July 1, 2008.

(3) Albuquerque-Bernalillo County Air Quality Control Board. The Albuquerque-Bernalillo County Air Quality Control Board has been delegated all part 60 standards promulgated by EPA, except Subpart AAA—Standards of Performance for New Residential Wood Heaters; Subpart WWW—Standards of Performance for Municipal Solid Waste Landfills; Subpart Cc—Emissions Guidelines and Compliance Times for Municipal Solid Waste Landfills, as amended in the Federal Register through July 1, 2004.

[40 FR 18169, Apr. 25, 1975]

Editorial Note: For Federal Register citations affecting §60.4 see the List of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at www.fdsys.gov.

§60.5   Determination of construction or modification.

(a) When requested to do so by an owner or operator, the Administrator will make a determination of whether action taken or intended to be taken by such owner or operator constitutes construction (including reconstruction) or modification or the commencement thereof within the meaning of this part.

(b) The Administrator will respond to any request for a determination under paragraph (a) of this section within 30 days of receipt of such request.

[40 FR 58418, Dec. 16, 1975]

§60.6   Review of plans.

(a) When requested to do so by an owner or operator, the Administrator will review plans for construction or modification for the purpose of providing technical advice to the owner or operator.

(b)(1) A separate request shall be submitted for each construction or modification project.

(2) Each request shall identify the location of such project, and be accompanied by technical information describing the proposed nature, size, design, and method of operation of each affected facility involved in such project, including information on any equipment to be used for measurement or control of emissions.

(c) Neither a request for plans review nor advice furnished by the Administrator in response to such request shall (1) relieve an owner or operator of legal responsibility for compliance with any provision of this part or of any applicable State or local requirement, or (2) prevent the Administrator from implementing or enforcing any provision of this part or taking any other action authorized by the Act.

[36 FR 24877, Dec. 23, 1971, as amended at 39 FR 9314, Mar. 8, 1974]

§60.7   Notification and record keeping.

(a) Any owner or operator subject to the provisions of this part shall furnish the Administrator written notification or, if acceptable to both the Administrator and the owner or operator of a source, electronic notification, as follows:

(1) A notification of the date construction (or reconstruction as defined under §60.15) of an affected facility is commenced postmarked no later than 30 days after such date. This requirement shall not apply in the case of mass-produced facilities which are purchased in completed form.

(2) [Reserved]

(3) A notification of the actual date of initial startup of an affected facility postmarked within 15 days after such date.

(4) A notification of any physical or operational change to an existing facility which may increase the emission rate of any air pollutant to which a standard applies, unless that change is specifically exempted under an applicable subpart or in §60.14(e). This notice shall be postmarked 60 days or as soon as practicable before the change is commenced and shall include information describing the precise nature of the change, present and proposed emission control systems, productive capacity of the facility before and after the change, and the expected completion date of the change. The Administrator may request additional relevant information subsequent to this notice.

(5) A notification of the date upon which demonstration of the continuous monitoring system performance commences in accordance with §60.13(c). Notification shall be postmarked not less than 30 days prior to such date.

(6) A notification of the anticipated date for conducting the opacity observations required by §60.11(e)(1) of this part. The notification shall also include, if appropriate, a request for the Administrator to provide a visible emissions reader during a performance test. The notification shall be postmarked not less than 30 days prior to such date.

(7) A notification that continuous opacity monitoring system data results will be used to determine compliance with the applicable opacity standard during a performance test required by §60.8 in lieu of Method 9 observation data as allowed by §60.11(e)(5) of this part. This notification shall be postmarked not less than 30 days prior to the date of the performance test.

(b) Any owner or operator subject to the provisions of this part shall maintain records of the occurrence and duration of any startup, shutdown, or malfunction in the operation of an affected facility; any malfunction of the air pollution control equipment; or any periods during which a continuous monitoring system or monitoring device is inoperative.

(c) Each owner or operator required to install a continuous monitoring device shall submit excess emissions and monitoring systems performance report (excess emissions are defined in applicable subparts) and-or summary report form (see paragraph (d) of this section) to the Administrator semiannually, except when: more frequent reporting is specifically required by an applicable subpart; or the Administrator, on a case-by-case basis, determines that more frequent reporting is necessary to accurately assess the compliance status of the source. All reports shall be postmarked by the 30th day following the end of each six-month period. Written reports of excess emissions shall include the following information:

(1) The magnitude of excess emissions computed in accordance with §60.13(h), any conversion factor(s) used, and the date and time of commencement and completion of each time period of excess emissions. The process operating time during the reporting period.

(2) Specific identification of each period of excess emissions that occurs during startups, shutdowns, and malfunctions of the affected facility. The nature and cause of any malfunction (if known), the corrective action taken or preventative measures adopted.

(3) The date and time identifying each period during which the continuous monitoring system was inoperative except for zero and span checks and the nature of the system repairs or adjustments.

(4) When no excess emissions have occurred or the continuous monitoring system(s) have not been inoperative, repaired, or adjusted, such information shall be stated in the report.

(d) The summary report form shall contain the information and be in the format shown in figure 1 unless otherwise specified by the Administrator. One summary report form shall be submitted for each pollutant monitored at each affected facility.

(1) If the total duration of excess emissions for the reporting period is less than 1 percent of the total operating time for the reporting period and CMS downtime for the reporting period is less than 5 percent of the total operating time for the reporting period, only the summary report form shall be submitted and the excess emission report described in §60.7(c) need not be submitted unless requested by the Administrator.

(2) If the total duration of excess emissions for the reporting period is 1 percent or greater of the total operating time for the reporting period or the total CMS downtime for the reporting period is 5 percent or greater of the total operating time for the reporting period, the summary report form and the excess emission report described in §60.7(c) shall both be submitted.

Figure 1—Summary Report—Gaseous and Opacity Excess Emission and Monitoring System Performance

Pollutant (Circle One—SO2/NOX/TRS/H2S/CO/Opacity)

Reporting period dates: From _____ to _____

Company:

Emission Limitation

Address:

Monitor Manufacturer and Model No.
Date of Latest CMS Certification or Audit

Process Unit(s) Description:

Total source operating time in reporting period1
Emission data summary1   CMS performance summary1   
1. Duration of excess emissions in reporting period due to:1. CMS downtime in reporting period due to:
a. Startup/shutdown   a. Monitor equipment malfunctions
b. Control equipment problems   b. Non-Monitor equipment malfunctions
c. Process problems   c. Quality assurance calibration
d. Other known causes   d. Other known causes
e. Unknown causes   e. Unknown causes
2. Total duration of excess emission2. Total CMS Downtime
3. Total duration of excess emissions × (100) [Total source operating time]%23. [Total CMS Downtime] × (100) [Total source operating time]%2

1For opacity, record all times in minutes. For gases, record all times in hours.

2For the reporting period: If the total duration of excess emissions is 1 percent or greater of the total operating time or the total CMS downtime is 5 percent or greater of the total operating time, both the summary report form and the excess emission report described in §60.7(c) shall be submitted.

On a separate page, describe any changes since last quarter in CMS, process or controls. I certify that the information contained in this report is true, accurate, and complete.

 

Name

 

Signature

 

Title

 

Date

(e)(1) Notwithstanding the frequency of reporting requirements specified in paragraph (c) of this section, an owner or operator who is required by an applicable subpart to submit excess emissions and monitoring systems performance reports (and summary reports) on a quarterly (or more frequent) basis may reduce the frequency of reporting for that standard to semiannual if the following conditions are met:

(i) For 1 full year (e.g., 4 quarterly or 12 monthly reporting periods) the affected facility's excess emissions and monitoring systems reports submitted to comply with a standard under this part continually demonstrate that the facility is in compliance with the applicable standard;

(ii) The owner or operator continues to comply with all recordkeeping and monitoring requirements specified in this subpart and the applicable standard; and

(iii) The Administrator does not object to a reduced frequency of reporting for the affected facility, as provided in paragraph (e)(2) of this section.

(2) The frequency of reporting of excess emissions and monitoring systems performance (and summary) reports may be reduced only after the owner or operator notifies the Administrator in writing of his or her intention to make such a change and the Administrator does not object to the intended change. In deciding whether to approve a reduced frequency of reporting, the Administrator may review information concerning the source's entire previous performance history during the required recordkeeping period prior to the intended change, including performance test results, monitoring data, and evaluations of an owner or operator's conformance with operation and maintenance requirements. Such information may be used by the Administrator to make a judgment about the source's potential for noncompliance in the future. If the Administrator disapproves the owner or operator's request to reduce the frequency of reporting, the Administrator will notify the owner or operator in writing within 45 days after receiving notice of the owner or operator's intention. The notification from the Administrator to the owner or operator will specify the grounds on which the disapproval is based. In the absence of a notice of disapproval within 45 days, approval is automatically granted.

(3) As soon as monitoring data indicate that the affected facility is not in compliance with any emission limitation or operating parameter specified in the applicable standard, the frequency of reporting shall revert to the frequency specified in the applicable standard, and the owner or operator shall submit an excess emissions and monitoring systems performance report (and summary report, if required) at the next appropriate reporting period following the noncomplying event. After demonstrating compliance with the applicable standard for another full year, the owner or operator may again request approval from the Administrator to reduce the frequency of reporting for that standard as provided for in paragraphs (e)(1) and (e)(2) of this section.

(f) Any owner or operator subject to the provisions of this part shall maintain a file of all measurements, including continuous monitoring system, monitoring device, and performance testing measurements; all continuous monitoring system performance evaluations; all continuous monitoring system or monitoring device calibration checks; adjustments and maintenance performed on these systems or devices; and all other information required by this part recorded in a permanent form suitable for inspection. The file shall be retained for at least two years following the date of such measurements, maintenance, reports, and records, except as follows:

(1) This paragraph applies to owners or operators required to install a continuous emissions monitoring system (CEMS) where the CEMS installed is automated, and where the calculated data averages do not exclude periods of CEMS breakdown or malfunction. An automated CEMS records and reduces the measured data to the form of the pollutant emission standard through the use of a computerized data acquisition system. In lieu of maintaining a file of all CEMS subhourly measurements as required under paragraph (f) of this section, the owner or operator shall retain the most recent consecutive three averaging periods of subhourly measurements and a file that contains a hard copy of the data acquisition system algorithm used to reduce the measured data into the reportable form of the standard.

(2) This paragraph applies to owners or operators required to install a CEMS where the measured data is manually reduced to obtain the reportable form of the standard, and where the calculated data averages do not exclude periods of CEMS breakdown or malfunction. In lieu of maintaining a file of all CEMS subhourly measurements as required under paragraph (f) of this section, the owner or operator shall retain all subhourly measurements for the most recent reporting period. The subhourly measurements shall be retained for 120 days from the date of the most recent summary or excess emission report submitted to the Administrator.

(3) The Administrator or delegated authority, upon notification to the source, may require the owner or operator to maintain all measurements as required by paragraph (f) of this section, if the Administrator or the delegated authority determines these records are required to more accurately assess the compliance status of the affected source.

(g) If notification substantially similar to that in paragraph (a) of this section is required by any other State or local agency, sending the Administrator a copy of that notification will satisfy the requirements of paragraph (a) of this section.

(h) Individual subparts of this part may include specific provisions which clarify or make inapplicable the provisions set forth in this section.

[36 FR 24877, Dec. 28, 1971, as amended at 40 FR 46254, Oct. 6, 1975; 40 FR 58418, Dec. 16, 1975; 45 FR 5617, Jan. 23, 1980; 48 FR 48335, Oct. 18, 1983; 50 FR 53113, Dec. 27, 1985; 52 FR 9781, Mar. 26, 1987; 55 FR 51382, Dec. 13, 1990; 59 FR 12428, Mar. 16, 1994; 59 FR 47265, Sep. 15, 1994; 64 FR 7463, Feb. 12, 1999]

§60.8   Performance tests.

(a) Except as specified in paragraphs (a)(1),(a)(2), (a)(3), and (a)(4) of this section, within 60 days after achieving the maximum production rate at which the affected facility will be operated, but not later than 180 days after initial startup of such facility, or at such other times specified by this part, and at such other times as may be required by the Administrator under section 114 of the Act, the owner or operator of such facility shall conduct performance test(s) and furnish the Administrator a written report of the results of such performance test(s).

(1) If a force majeure is about to occur, occurs, or has occurred for which the affected owner or operator intends to assert a claim of force majeure, the owner or operator shall notify the Administrator, in writing as soon as practicable following the date the owner or operator first knew, or through due diligence should have known that the event may cause or caused a delay in testing beyond the regulatory deadline, but the notification must occur before the performance test deadline unless the initial force majeure or a subsequent force majeure event delays the notice, and in such cases, the notification shall occur as soon as practicable.

(2) The owner or operator shall provide to the Administrator a written description of the force majeure event and a rationale for attributing the delay in testing beyond the regulatory deadline to the force majeure; describe the measures taken or to be taken to minimize the delay; and identify a date by which the owner or operator proposes to conduct the performance test. The performance test shall be conducted as soon as practicable after the force majeure occurs.

(3) The decision as to whether or not to grant an extension to the performance test deadline is solely within the discretion of the Administrator. The Administrator will notify the owner or operator in writing of approval or disapproval of the request for an extension as soon as practicable.

(4) Until an extension of the performance test deadline has been approved by the Administrator under paragraphs (a)(1), (2), and (3) of this section, the owner or operator of the affected facility remains strictly subject to the requirements of this part.

(b) Performance tests shall be conducted and data reduced in accordance with the test methods and procedures contained in each applicable subpart unless the Administrator (1) specifies or approves, in specific cases, the use of a reference method with minor changes in methodology, (2) approves the use of an equivalent method, (3) approves the use of an alternative method the results of which he has determined to be adequate for indicating whether a specific source is in compliance, (4) waives the requirement for performance tests because the owner or operator of a source has demonstrated by other means to the Administrator's satisfaction that the affected facility is in compliance with the standard, or (5) approves shorter sampling times and smaller sample volumes when necessitated by process variables or other factors. Nothing in this paragraph shall be construed to abrogate the Administrator's authority to require testing under section 114 of the Act.

(c) Performance tests shall be conducted under such conditions as the Administrator shall specify to the plant operator based on representative performance of the affected facility. The owner or operator shall make available to the Administrator such records as may be necessary to determine the conditions of the performance tests. Operations during periods of startup, shutdown, and malfunction shall not constitute representative conditions for the purpose of a performance test nor shall emissions in excess of the level of the applicable emission limit during periods of startup, shutdown, and malfunction be considered a violation of the applicable emission limit unless otherwise specified in the applicable standard.

(d) The owner or operator of an affected facility shall provide the Administrator at least 30 days prior notice of any performance test, except as specified under other subparts, to afford the Administrator the opportunity to have an observer present. If after 30 days notice for an initially scheduled performance test, there is a delay (due to operational problems, etc.) in conducting the scheduled performance test, the owner or operator of an affected facility shall notify the Administrator (or delegated State or local agency) as soon as possible of any delay in the original test date, either by providing at least 7 days prior notice of the rescheduled date of the performance test, or by arranging a rescheduled date with the Administrator (or delegated State or local agency) by mutual agreement.

(e) The owner or operator of an affected facility shall provide, or cause to be provided, performance testing facilities as follows:

(1) Sampling ports adequate for test methods applicable to such facility. This includes (i) constructing the air pollution control system such that volumetric flow rates and pollutant emission rates can be accurately determined by applicable test methods and procedures and (ii) providing a stack or duct free of cyclonic flow during performance tests, as demonstrated by applicable test methods and procedures.

(2) Safe sampling platform(s).

(3) Safe access to sampling platform(s).

(4) Utilities for sampling and testing equipment.

(f) Unless otherwise specified in the applicable subpart, each performance test shall consist of three separate runs using the applicable test method. Each run shall be conducted for the time and under the conditions specified in the applicable standard. For the purpose of determining compliance with an applicable standard, the arithmetic means of results of the three runs shall apply. In the event that a sample is accidentally lost or conditions occur in which one of the three runs must be discontinued because of forced shutdown, failure of an irreplaceable portion of the sample train, extreme meteorological conditions, or other circumstances, beyond the owner or operator's control, compliance may, upon the Administrator's approval, be determined using the arithmetic mean of the results of the two other runs.

(g) The performance testing shall include a test method performance audit (PA) during the performance test. The PAs consist of blind audit samples supplied by an accredited audit sample provider and analyzed during the performance test in order to provide a measure of test data bias. Gaseous audit samples are designed to audit the performance of the sampling system as well as the analytical system and must be collected by the sampling system during the compliance test just as the compliance samples are collected. If a liquid or solid audit sample is designed to audit the sampling system, it must also be collected by the sampling system during the compliance test. If multiple sampling systems or sampling trains are used during the compliance test for any of the test methods, the tester is only required to use one of the sampling systems per method to collect the audit sample. The audit sample must be analyzed by the same analyst using the same analytical reagents and analytical system and at the same time as the compliance samples. Retests are required when there is a failure to produce acceptable results for an audit sample. However, if the audit results do not affect the compliance or noncompliance status of the affected facility, the compliance authority may waive the reanalysis requirement, further audits, or retests and accept the results of the compliance test. Acceptance of the test results shall constitute a waiver of the reanalysis requirement, further audits, or retests. The compliance authority may also use the audit sample failure and the compliance test results as evidence to determine the compliance or noncompliance status of the affected facility. A blind audit sample is a sample whose value is known only to the sample provider and is not revealed to the tested facility until after they report the measured value of the audit sample. For pollutants that exist in the gas phase at ambient temperature, the audit sample shall consist of an appropriate concentration of the pollutant in air or nitrogen that can be introduced into the sampling system of the test method at or near the same entry point as a sample from the emission source. If no gas phase audit samples are available, an acceptable alternative is a sample of the pollutant in the same matrix that would be produced when the sample is recovered from the sampling system as required by the test method. For samples that exist only in a liquid or solid form at ambient temperature, the audit sample shall consist of an appropriate concentration of the pollutant in the same matrix that would be produced when the sample is recovered from the sampling system as required by the test method. An accredited audit sample provider (AASP) is an organization that has been accredited to prepare audit samples by an independent, third party accrediting body.

(1) The source owner, operator, or representative of the tested facility shall obtain an audit sample, if commercially available, from an AASP for each test method used for regulatory compliance purposes. No audit samples are required for the following test methods: Methods 3A and 3C of appendix A-3 of part 60, Methods 6C, 7E, 9, and 10 of appendix A-4 of part 60, Methods 18 and 19 of appendix A-6 of part 60, Methods 20, 22, and 25A of appendix A-7 of part 60, Methods 30A and 30B of appendix A-8 of part 60, and Methods 303, 318, 320, and 321 of appendix A of part 63 of this chapter. If multiple sources at a single facility are tested during a compliance test event, only one audit sample is required for each method used during a compliance test. The compliance authority responsible for the compliance test may waive the requirement to include an audit sample if they believe that an audit sample is not necessary. “Commercially available” means that two or more independent AASPs have blind audit samples available for purchase. If the source owner, operator, or representative cannot find an audit sample for a specific method, the owner, operator, or representative shall consult the EPA Web site at the following URL, www.epa.gov/ttn/emc, to confirm whether there is a source that can supply an audit sample for that method. If the EPA Web site does not list an available audit sample at least 60 days prior to the beginning of the compliance test, the source owner, operator, or representative shall not be required to include an audit sample as part of the quality assurance program for the compliance test. When ordering an audit sample, the source owner, operator, or representative shall give the sample provider an estimate for the concentration of each pollutant that is emitted by the source or the estimated concentration of each pollutant based on the permitted level and the name, address, and phone number of the compliance authority. The source owner, operator, or representative shall report the results for the audit sample along with a summary of the emission test results for the audited pollutant to the compliance authority and shall report the results of the audit sample to the AASP. The source owner, operator, or representative shall make both reports at the same time and in the same manner or shall report to the compliance authority first and then report to the AASP. If the method being audited is a method that allows the samples to be analyzed in the field and the tester plans to analyze the samples in the field, the tester may analyze the audit samples prior to collecting the emission samples provided a representative of the compliance authority is present at the testing site. The tester may request and the compliance authority may grant a waiver to the requirement that a representative of the compliance authority must be present at the testing site during the field analysis of an audit sample. The source owner, operator, or representative may report the results of the audit sample to the compliance authority and report the results of the audit sample to the AASP prior to collecting any emission samples. The test protocol and final test report shall document whether an audit sample was ordered and utilized and the pass/fail results as applicable.

(2) An AASP shall have and shall prepare, analyze, and report the true value of audit samples in accordance with a written technical criteria document that describes how audit samples will be prepared and distributed in a manner that will ensure the integrity of the audit sample program. An acceptable technical criteria document shall contain standard operating procedures for all of the following operations:

(i) Preparing the sample;

(ii) Confirming the true concentration of the sample;

(iii) Defining the acceptance limits for the results from a well qualified tester. This procedure must use well established statistical methods to analyze historical results from well qualified testers. The acceptance limits shall be set so that there is 95 percent confidence that 90 percent of well qualified labs will produce future results that are within the acceptance limit range.

(iv) Providing the opportunity for the compliance authority to comment on the selected concentration level for an audit sample;

(v) Distributing the sample to the user in a manner that guarantees that the true value of the sample is unknown to the user;

(vi) Recording the measured concentration reported by the user and determining if the measured value is within acceptable limits;

(vii) The AASP shall report the results from each audit sample in a timely manner to the compliance authority and then to the source owner, operator, or representative. The AASP shall make both reports at the same time and in the same manner or shall report to the compliance authority first and then report to the source owner, operator, or representative. The results shall include the name of the facility tested, the date on which the compliance test was conducted, the name of the company performing the sample collection, the name of the company that analyzed the compliance samples including the audit sample, the measured result for the audit sample, and whether the testing company passed or failed the audit. The AASP shall report the true value of the audit sample to the compliance authority. The AASP may report the true value to the source owner, operator, or representative if the AASP's operating plan ensures that no laboratory will receive the same audit sample twice.

(viii) Evaluating the acceptance limits of samples at least once every two years to determine in cooperation with the voluntary consensus standard body if they should be changed;

(ix) Maintaining a database, accessible to the compliance authorities, of results from the audit that shall include the name of the facility tested, the date on which the compliance test was conducted, the name of the company performing the sample collection, the name of the company that analyzed the compliance samples including the audit sample, the measured result for the audit sample, the true value of the audit sample, the acceptance range for the measured value, and whether the testing company passed or failed the audit.

(3) The accrediting body shall have a written technical criteria document that describes how it will ensure that the AASP is operating in accordance with the AASP technical criteria document that describes how audit samples are to be prepared and distributed. This document shall contain standard operating procedures for all of the following operations:

(i) Checking audit samples to confirm their true value as reported by the AASP;

(ii) Performing technical systems audits of the AASP's facilities and operating procedures at least once every two years;

(iii) Providing standards for use by the voluntary consensus standard body to approve the accrediting body that will accredit the audit sample providers.

(4) The technical criteria documents for the accredited sample providers and the accrediting body shall be developed through a public process guided by a voluntary consensus standards body (VCSB). The VCSB shall operate in accordance with the procedures and requirements in the Office of Management and Budget Circular A-119. A copy of Circular A-119 is available upon request by writing the Office of Information and Regulatory Affairs, Office of Management and Budget, 725 17th Street, NW., Washington, DC 20503, by calling (202) 395-6880 or downloading online at http://standards.gov/standards_gov/a119.cfm. The VCSB shall approve all accrediting bodies. The Administrator will review all technical criteria documents. If the technical criteria documents do not meet the minimum technical requirements in paragraphs (g)(2) through (4)of this section, the technical criteria documents are not acceptable and the proposed audit sample program is not capable of producing audit samples of sufficient quality to be used in a compliance test. All acceptable technical criteria documents shall be posted on the EPA Web site at the following URL, http://www.epa.gov/ttn/emc.

(h) Unless otherwise specified in the applicable subpart, each test location must be verified to be free of cyclonic flow and evaluated for the existence of emission gas stratification and the required number of sampling traverse points. If other procedures are not specified in the applicable subpart to the regulations, use the appropriate procedures in Method 1 to check for cyclonic flow and Method 7E to evaluate emission gas stratification and selection of sampling points.

(i) Whenever the use of multiple calibration gases is required by a test method, performance specification, or quality assurance procedure in a part 60 standard or appendix, Method 205 of 40 CFR part 51, appendix M of this chapter, “Verification of Gas Dilution Systems for Field Instrument Calibrations,” may be used.

[36 FR 24877, Dec. 23, 1971, as amended at 39 FR 9314, Mar. 8, 1974; 42 FR 57126, Nov. 1, 1977; 44 FR 33612, June 11, 1979; 54 FR 6662, Feb. 14, 1989; 54 FR 21344, May 17, 1989; 64 FR 7463, Feb. 12, 1999; 72 FR 27442, May 16, 2007; 75 FR 55646, Sept. 13, 2010; 79 FR 11241, Feb. 27, 2014]

§60.9   Availability of information.

The availability to the public of information provided to, or otherwise obtained by, the Administrator under this part shall be governed by part 2 of this chapter. (Information submitted voluntarily to the Administrator for the purposes of §§60.5 and 60.6 is governed by §§2.201 through 2.213 of this chapter and not by §2.301 of this chapter.)

§60.10   State authority.

The provisions of this part shall not be construed in any manner to preclude any State or political subdivision thereof from:

(a) Adopting and enforcing any emission standard or limitation applicable to an affected facility, provided that such emission standard or limitation is not less stringent than the standard applicable to such facility.

(b) Requiring the owner or operator of an affected facility to obtain permits, licenses, or approvals prior to initiating construction, modification, or operation of such facility.

§60.11   Compliance with standards and maintenance requirements.

(a) Compliance with standards in this part, other than opacity standards, shall be determined in accordance with performance tests established by §60.8, unless otherwise specified in the applicable standard.

(b) Compliance with opacity standards in this part shall be determined by conducting observations in accordance with Method 9 in appendix A of this part, any alternative method that is approved by the Administrator, or as provided in paragraph (e)(5) of this section. For purposes of determining initial compliance, the minimum total time of observations shall be 3 hours (30 6-minute averages) for the performance test or other set of observations (meaning those fugitive-type emission sources subject only to an opacity standard).

(c) The opacity standards set forth in this part shall apply at all times except during periods of startup, shutdown, malfunction, and as otherwise provided in the applicable standard.

(d) At all times, including periods of startup, shutdown, and malfunction, owners and operators shall, to the extent practicable, maintain and operate any affected facility including associated air pollution control equipment in a manner consistent with good air pollution control practice for minimizing emissions. Determination of whether acceptable operating and maintenance procedures are being used will be based on information available to the Administrator which may include, but is not limited to, monitoring results, opacity observations, review of operating and maintenance procedures, and inspection of the source.

(e)(1) For the purpose of demonstrating initial compliance, opacity observations shall be conducted concurrently with the initial performance test required in §60.8 unless one of the following conditions apply. If no performance test under §60.8 is required, then opacity observations shall be conducted within 60 days after achieving the maximum production rate at which the affected facility will be operated but no later than 180 days after initial startup of the facility. If visibility or other conditions prevent the opacity observations from being conducted concurrently with the initial performance test required under §60.8, the source owner or operator shall reschedule the opacity observations as soon after the initial performance test as possible, but not later than 30 days thereafter, and shall advise the Administrator of the rescheduled date. In these cases, the 30-day prior notification to the Administrator required in §60.7(a)(6) shall be waived. The rescheduled opacity observations shall be conducted (to the extent possible) under the same operating conditions that existed during the initial performance test conducted under §60.8. The visible emissions observer shall determine whether visibility or other conditions prevent the opacity observations from being made concurrently with the initial performance test in accordance with procedures contained in Method 9 of appendix B of this part. Opacity readings of portions of plumes which contain condensed, uncombined water vapor shall not be used for purposes of determing compliance with opacity standards. The owner or operator of an affected facility shall make available, upon request by the Administrator, such records as may be necessary to determine the conditions under which the visual observations were made and shall provide evidence indicating proof of current visible observer emission certification. Except as provided in paragraph (e)(5) of this section, the results of continuous monitoring by transmissometer which indicate that the opacity at the time visual observations were made was not in excess of the standard are probative but not conclusive evidence of the actual opacity of an emission, provided that the source shall meet the burden of proving that the instrument used meets (at the time of the alleged violation) Performance Specification 1 in appendix B of this part, has been properly maintained and (at the time of the alleged violation) that the resulting data have not been altered in any way.

(2) Except as provided in paragraph (e)(3) of this section, the owner or operator of an affected facility to which an opacity standard in this part applies shall conduct opacity observations in accordance with paragraph (b) of this section, shall record the opacity of emissions, and shall report to the Administrator the opacity results along with the results of the initial performance test required under §60.8. The inability of an owner or operator to secure a visible emissions observer shall not be considered a reason for not conducting the opacity observations concurrent with the initial performance test.

(3) The owner or operator of an affected facility to which an opacity standard in this part applies may request the Administrator to determine and to record the opacity of emissions from the affected facility during the initial performance test and at such times as may be required. The owner or operator of the affected facility shall report the opacity results. Any request to the Administrator to determine and to record the opacity of emissions from an affected facility shall be included in the notification required in §60.7(a)(6). If, for some reason, the Administrator cannot determine and record the opacity of emissions from the affected facility during the performance test, then the provisions of paragraph (e)(1) of this section shall apply.

(4) An owner or operator of an affected facility using a continuous opacity monitor (transmissometer) shall record the monitoring data produced during the initial performance test required by §60.8 and shall furnish the Administrator a written report of the monitoring results along with Method 9 and §60.8 performance test results.

(5) An owner or operator of an affected facility subject to an opacity standard may submit, for compliance purposes, continuous opacity monitoring system (COMS) data results produced during any performance test required under §60.8 in lieu of Method 9 observation data. If an owner or operator elects to submit COMS data for compliance with the opacity standard, he shall notify the Administrator of that decision, in writing, at least 30 days before any performance test required under §60.8 is conducted. Once the owner or operator of an affected facility has notified the Administrator to that effect, the COMS data results will be used to determine opacity compliance during subsequent tests required under §60.8 until the owner or operator notifies the Administrator, in writing, to the contrary. For the purpose of determining compliance with the opacity standard during a performance test required under §60.8 using COMS data, the minimum total time of COMS data collection shall be averages of all 6-minute continuous periods within the duration of the mass emission performance test. Results of the COMS opacity determinations shall be submitted along with the results of the performance test required under §60.8. The owner or operator of an affected facility using a COMS for compliance purposes is responsible for demonstrating that the COMS meets the requirements specified in §60.13(c) of this part, that the COMS has been properly maintained and operated, and that the resulting data have not been altered in any way. If COMS data results are submitted for compliance with the opacity standard for a period of time during which Method 9 data indicates noncompliance, the Method 9 data will be used to determine compliance with the opacity standard.

(6) Upon receipt from an owner or operator of the written reports of the results of the performance tests required by §60.8, the opacity observation results and observer certification required by §60.11(e)(1), and the COMS results, if applicable, the Administrator will make a finding concerning compliance with opacity and other applicable standards. If COMS data results are used to comply with an opacity standard, only those results are required to be submitted along with the performance test results required by §60.8. If the Administrator finds that an affected facility is in compliance with all applicable standards for which performance tests are conducted in accordance with §60.8 of this part but during the time such performance tests are being conducted fails to meet any applicable opacity standard, he shall notify the owner or operator and advise him that he may petition the Administrator within 10 days of receipt of notification to make appropriate adjustment to the opacity standard for the affected facility.

(7) The Administrator will grant such a petition upon a demonstration by the owner or operator that the affected facility and associated air pollution control equipment was operated and maintained in a manner to minimize the opacity of emissions during the performance tests; that the performance tests were performed under the conditions established by the Administrator; and that the affected facility and associated air pollution control equipment were incapable of being adjusted or operated to meet the applicable opacity standard.

(8) The Administrator will establish an opacity standard for the affected facility meeting the above requirements at a level at which the source will be able, as indicated by the performance and opacity tests, to meet the opacity standard at all times during which the source is meeting the mass or concentration emission standard. The Administrator will promulgate the new opacity standard in the Federal Register.

(f) Special provisions set forth under an applicable subpart shall supersede any conflicting provisions in paragraphs (a) through (e) of this section.

(g) For the purpose of submitting compliance certifications or establishing whether or not a person has violated or is in violation of any standard in this part, nothing in this part shall preclude the use, including the exclusive use, of any credible evidence or information, relevant to whether a source would have been in compliance with applicable requirements if the appropriate performance or compliance test or procedure had been performed.

[38 FR 28565, Oct. 15, 1973, as amended at 39 FR 39873, Nov. 12, 1974; 43 FR 8800, Mar. 3, 1978; 45 FR 23379, Apr. 4, 1980; 48 FR 48335, Oct. 18, 1983; 50 FR 53113, Dec. 27, 1985; 51 FR 1790, Jan. 15, 1986; 52 FR 9781, Mar. 26, 1987; 62 FR 8328, Feb. 24, 1997; 65 FR 61749, Oct. 17, 2000]

§60.12   Circumvention.

No owner or operator subject to the provisions of this part shall build, erect, install, or use any article, machine, equipment or process, the use of which conceals an emission which would otherwise constitute a violation of an applicable standard. Such concealment includes, but is not limited to, the use of gaseous diluents to achieve compliance with an opacity standard or with a standard which is based on the concentration of a pollutant in the gases discharged to the atmosphere.

[39 FR 9314, Mar. 8, 1974]

§60.13   Monitoring requirements.

(a) For the purposes of this section, all continuous monitoring systems required under applicable subparts shall be subject to the provisions of this section upon promulgation of performance specifications for continuous monitoring systems under appendix B to this part and, if the continuous monitoring system is used to demonstrate compliance with emission limits on a continuous basis, appendix F to this part, unless otherwise specified in an applicable subpart or by the Administrator. Appendix F is applicable December 4, 1987.

(b) All continuous monitoring systems and monitoring devices shall be installed and operational prior to conducting performance tests under §60.8. Verification of operational status shall, as a minimum, include completion of the manufacturer's written requirements or recommendations for installation, operation, and calibration of the device.

(c) If the owner or operator of an affected facility elects to submit continous opacity monitoring system (COMS) data for compliance with the opacity standard as provided under §60.11(e)(5), he shall conduct a performance evaluation of the COMS as specified in Performance Specification 1, appendix B, of this part before the performance test required under §60.8 is conducted. Otherwise, the owner or operator of an affected facility shall conduct a performance evaluation of the COMS or continuous emission monitoring system (CEMS) during any performance test required under §60.8 or within 30 days thereafter in accordance with the applicable performance specification in appendix B of this part, The owner or operator of an affected facility shall conduct COMS or CEMS performance evaluations at such other times as may be required by the Administrator under section 114 of the Act.

(1) The owner or operator of an affected facility using a COMS to determine opacity compliance during any performance test required under §60.8 and as described in §60.11(e)(5) shall furnish the Administrator two or, upon request, more copies of a written report of the results of the COMS performance evaluation described in paragraph (c) of this section at least 10 days before the performance test required under §60.8 is conducted.

(2) Except as provided in paragraph (c)(1) of this section, the owner or operator of an affected facility shall furnish the Administrator within 60 days of completion two or, upon request, more copies of a written report of the results of the performance evaluation.

(d)(1) Owners and operators of a CEMS installed in accordance with the provisions of this part, must check the zero (or low level value between 0 and 20 percent of span value) and span (50 to 100 percent of span value) calibration drifts at least once each operating day in accordance with a written procedure. The zero and span must, at a minimum, be adjusted whenever either the 24-hour zero drift or the 24-hour span drift exceeds two times the limit of the applicable performance specification in appendix B of this part. The system must allow the amount of the excess zero and span drift to be recorded and quantified whenever specified. Owners and operators of a COMS installed in accordance with the provisions of this part must check the zero and upscale (span) calibration drifts at least once daily. For a particular COMS, the acceptable range of zero and upscale calibration materials is defined in the applicable version of PS-1 in appendix B of this part. For a COMS, the optical surfaces, exposed to the effluent gases, must be cleaned before performing the zero and upscale drift adjustments, except for systems using automatic zero adjustments. The optical surfaces must be cleaned when the cumulative automatic zero compensation exceeds 4 percent opacity.

(2) Unless otherwise approved by the Administrator, the following procedures must be followed for a COMS. Minimum procedures must include an automated method for producing a simulated zero opacity condition and an upscale opacity condition using a certified neutral density filter or other related technique to produce a known obstruction of the light beam. Such procedures must provide a system check of all active analyzer internal optics with power or curvature, all active electronic circuitry including the light source and photodetector assembly, and electronic or electro-mechanical systems and hardware and or software used during normal measurement operation.

(e) Except for system breakdowns, repairs, calibration checks, and zero and span adjustments required under paragraph (d) of this section, all continuous monitoring systems shall be in continuous operation and shall meet minimum frequency of operation requirements as follows:

(1) All continuous monitoring systems referenced by paragraph (c) of this section for measuring opacity of emissions shall complete a minimum of one cycle of sampling and analyzing for each successive 10-second period and one cycle of data recording for each successive 6-minute period.

(2) All continuous monitoring systems referenced by paragraph (c) of this section for measuring emissions, except opacity, shall complete a minimum of one cycle of operation (sampling, analyzing, and data recording) for each successive 15-minute period.

(f) All continuous monitoring systems or monitoring devices shall be installed such that representative measurements of emissions or process parameters from the affected facility are obtained. Additional procedures for location of continuous monitoring systems contained in the applicable Performance Specifications of appendix B of this part shall be used.

(g) When the effluents from a single affected facility or two or more affected facilities subject to the same emission standards are combined before being released to the atmosphere, the owner or operator may install applicable continuous monitoring systems on each effluent or on the combined effluent. When the affected facilities are not subject to the same emission standards, separate continuous monitoring systems shall be installed on each effluent. When the effluent from one affected facility is released to the atmosphere through more than one point, the owner or operator shall install an applicable continuous monitoring system on each separate effluent unless the installation of fewer systems is approved by the Administrator. When more than one continuous monitoring system is used to measure the emissions from one affected facility (e.g., multiple breechings, multiple outlets), the owner or operator shall report the results as required from each continuous monitoring system.

(h)(1) Owners or operators of all continuous monitoring systems for measurement of opacity shall reduce all data to 6-minute averages and for continuous monitoring systems other than opacity to 1-hour averages for time periods as defined in §60.2. Six-minute opacity averages shall be calculated from 36 or more data points equally spaced over each 6-minute period.

(2) For continuous monitoring systems other than opacity, 1-hour averages shall be computed as follows, except that the provisions pertaining to the validation of partial operating hours are only applicable for affected facilities that are required by the applicable subpart to include partial hours in the emission calculations:

(i) Except as provided under paragraph (h)(2)(iii) of this section, for a full operating hour (any clock hour with 60 minutes of unit operation), at least four valid data points are required to calculate the hourly average, i.e., one data point in each of the 15-minute quadrants of the hour.

(ii) Except as provided under paragraph (h)(2)(iii) of this section, for a partial operating hour (any clock hour with less than 60 minutes of unit operation), at least one valid data point in each 15-minute quadrant of the hour in which the unit operates is required to calculate the hourly average.

(iii) For any operating hour in which required maintenance or quality-assurance activities are performed:

(A) If the unit operates in two or more quadrants of the hour, a minimum of two valid data points, separated by at least 15 minutes, is required to calculate the hourly average; or

(B) If the unit operates in only one quadrant of the hour, at least one valid data point is required to calculate the hourly average.

(iv) If a daily calibration error check is failed during any operating hour, all data for that hour shall be invalidated, unless a subsequent calibration error test is passed in the same hour and the requirements of paragraph (h)(2)(iii) of this section are met, based solely on valid data recorded after the successful calibration.

(v) For each full or partial operating hour, all valid data points shall be used to calculate the hourly average.

(vi) Except as provided under paragraph (h)(2)(vii) of this section, data recorded during periods of continuous monitoring system breakdown, repair, calibration checks, and zero and span adjustments shall not be included in the data averages computed under this paragraph.

(vii) Owners and operators complying with the requirements of §60.7(f)(1) or (2) must include any data recorded during periods of monitor breakdown or malfunction in the data averages.

(viii) When specified in an applicable subpart, hourly averages for certain partial operating hours shall not be computed or included in the emission averages (e.g., hours with 30 minutes of unit operation under §60.47b(d)).

(ix) Either arithmetic or integrated averaging of all data may be used to calculate the hourly averages. The data may be recorded in reduced or nonreduced form (e.g., ppm pollutant and percent O2 or ng/J of pollutant).

(3) All excess emissions shall be converted into units of the standard using the applicable conversion procedures specified in the applicable subpart. After conversion into units of the standard, the data may be rounded to the same number of significant digits used in the applicable subpart to specify the emission limit.

(i) After receipt and consideration of written application, the Administrator may approve alternatives to any monitoring procedures or requirements of this part including, but not limited to the following:

(1) Alternative monitoring requirements when installation of a continuous monitoring system or monitoring device specified by this part would not provide accurate measurements due to liquid water or other interferences caused by substances in the effluent gases.

(2) Alternative monitoring requirements when the affected facility is infrequently operated.

(3) Alternative monitoring requirements to accommodate continuous monitoring systems that require additional measurements to correct for stack moisture conditions.

(4) Alternative locations for installing continuous monitoring systems or monitoring devices when the owner or operator can demonstrate that installation at alternate locations will enable accurate and representative measurements.

(5) Alternative methods of converting pollutant concentration measurements to units of the standards.

(6) Alternative procedures for performing daily checks of zero and span drift that do not involve use of span gases or test cells.

(7) Alternatives to the A.S.T.M. test methods or sampling procedures specified by any subpart.

(8) Alternative continuous monitoring systems that do not meet the design or performance requirements in Performance Specification 1, appendix B, but adequately demonstrate a definite and consistent relationship between its measurements and the measurements of opacity by a system complying with the requirements in Performance Specification 1. The Administrator may require that such demonstration be performed for each affected facility.

(9) Alternative monitoring requirements when the effluent from a single affected facility or the combined effluent from two or more affected facilities is released to the atmosphere through more than one point.

(j) An alternative to the relative accuracy (RA) test specified in Performance Specification 2 of appendix B may be requested as follows:

(1) An alternative to the reference method tests for determining RA is available for sources with emission rates demonstrated to be less than 50 percent of the applicable standard. A source owner or operator may petition the Administrator to waive the RA test in Section 8.4 of Performance Specification 2 and substitute the procedures in Section 16.0 if the results of a performance test conducted according to the requirements in §60.8 of this subpart or other tests performed following the criteria in §60.8 demonstrate that the emission rate of the pollutant of interest in the units of the applicable standard is less than 50 percent of the applicable standard. For sources subject to standards expressed as control efficiency levels, a source owner or operator may petition the Administrator to waive the RA test and substitute the procedures in Section 16.0 of Performance Specification 2 if the control device exhaust emission rate is less than 50 percent of the level needed to meet the control efficiency requirement. The alternative procedures do not apply if the continuous emission monitoring system is used to determine compliance continuously with the applicable standard. The petition to waive the RA test shall include a detailed description of the procedures to be applied. Included shall be location and procedure for conducting the alternative, the concentration or response levels of the alternative RA materials, and the other equipment checks included in the alternative procedure. The Administrator will review the petition for completeness and applicability. The determination to grant a waiver will depend on the intended use of the CEMS data (e.g., data collection purposes other than NSPS) and may require specifications more stringent than in Performance Specification 2 (e.g., the applicable emission limit is more stringent than NSPS).

(2) The waiver of a CEMS RA test will be reviewed and may be rescinded at such time, following successful completion of the alternative RA procedure, that the CEMS data indicate that the source emissions are approaching the level. The criterion for reviewing the waiver is the collection of CEMS data showing that emissions have exceeded 70 percent of the applicable standard for seven, consecutive, averaging periods as specified by the applicable regulation(s). For sources subject to standards expressed as control efficiency levels, the criterion for reviewing the waiver is the collection of CEMS data showing that exhaust emissions have exceeded 70 percent of the level needed to meet the control efficiency requirement for seven, consecutive, averaging periods as specified by the applicable regulation(s) [e.g., §60.45(g) (2) and (3), §60.73(e), and §60.84(e)]. It is the responsibility of the source operator to maintain records and determine the level of emissions relative to the criterion on the waiver of RA testing. If this criterion is exceeded, the owner or operator must notify the Administrator within 10 days of such occurrence and include a description of the nature and cause of the increasing emissions. The Administrator will review the notification and may rescind the waiver and require the owner or operator to conduct a RA test of the CEMS as specified in Section 8.4 of Performance Specification 2.

[40 FR 46255, Oct. 6, 1975]

Editorial Note: For Federal Register citations affecting §60.13, see the List of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and on GPO Access.

Editorial Note: At 65 FR 61749, Oct. 17, 2000, §60.13 was amended by revising the words “ng/J of pollutant” to read “ng of pollutant per J of heat input” in the sixth sentence of paragraph (h). However, the amendment could not be incorporated because the words “ng/J of pollutant” do not appear in the sixth sentence of paragraph (h).

§60.14   Modification.

(a) Except as provided under paragraphs (e) and (f) of this section, any physical or operational change to an existing facility which results in an increase in the emission rate to the atmosphere of any pollutant to which a standard applies shall be considered a modification within the meaning of section 111 of the Act. Upon modification, an existing facility shall become an affected facility for each pollutant to which a standard applies and for which there is an increase in the emission rate to the atmosphere.

(b) Emission rate shall be expressed as kg/hr of any pollutant discharged into the atmosphere for which a standard is applicable. The Administrator shall use the following to determine emission rate:

(1) Emission factors as specified in the latest issue of “Compilation of Air Pollutant Emission Factors,” EPA Publication No. AP-42, or other emission factors determined by the Administrator to be superior to AP-42 emission factors, in cases where utilization of emission factors demonstrates that the emission level resulting from the physical or operational change will either clearly increase or clearly not increase.

(2) Material balances, continuous monitor data, or manual emission tests in cases where utilization of emission factors as referenced in paragraph (b)(1) of this section does not demonstrate to the Administrator's satisfaction whether the emission level resulting from the physical or operational change will either clearly increase or clearly not increase, or where an owner or operator demonstrates to the Administrator's satisfaction that there are reasonable grounds to dispute the result obtained by the Administrator utilizing emission factors as referenced in paragraph (b)(1) of this section. When the emission rate is based on results from manual emission tests or continuous monitoring systems, the procedures specified in appendix C of this part shall be used to determine whether an increase in emission rate has occurred. Tests shall be conducted under such conditions as the Administrator shall specify to the owner or operator based on representative performance of the facility. At least three valid test runs must be conducted before and at least three after the physical or operational change. All operating parameters which may affect emissions must be held constant to the maximum feasible degree for all test runs.

(c) The addition of an affected facility to a stationary source as an expansion to that source or as a replacement for an existing facility shall not by itself bring within the applicability of this part any other facility within that source.

(d) [Reserved]

(e) The following shall not, by themselves, be considered modifications under this part:

(1) Maintenance, repair, and replacement which the Administrator determines to be routine for a source category, subject to the provisions of paragraph (c) of this section and §60.15.

(2) An increase in production rate of an existing facility, if that increase can be accomplished without a capital expenditure on that facility.

(3) An increase in the hours of operation.

(4) Use of an alternative fuel or raw material if, prior to the date any standard under this part becomes applicable to that source type, as provided by §60.1, the existing facility was designed to accommodate that alternative use. A facility shall be considered to be designed to accommodate an alternative fuel or raw material if that use could be accomplished under the facility's construction specifications as amended prior to the change. Conversion to coal required for energy considerations, as specified in section 111(a)(8) of the Act, shall not be considered a modification.

(5) The addition or use of any system or device whose primary function is the reduction of air pollutants, except when an emission control system is removed or is replaced by a system which the Administrator determines to be less environmentally beneficial.

(6) The relocation or change in ownership of an existing facility.

(f) Special provisions set forth under an applicable subpart of this part shall supersede any conflicting provisions of this section.

(g) Within 180 days of the completion of any physical or operational change subject to the control measures specified in paragraph (a) of this section, compliance with all applicable standards must be achieved.

(h) No physical change, or change in the method of operation, at an existing electric utility steam generating unit shall be treated as a modification for the purposes of this section provided that such change does not increase the maximum hourly emissions of any pollutant regulated under this section above the maximum hourly emissions achievable at that unit during the 5 years prior to the change.

(i) Repowering projects that are awarded funding from the Department of Energy as permanent clean coal technology demonstration projects (or similar projects funded by EPA) are exempt from the requirements of this section provided that such change does not increase the maximum hourly emissions of any pollutant regulated under this section above the maximum hourly emissions achievable at that unit during the five years prior to the change.

(j)(1) Repowering projects that qualify for an extension under section 409(b) of the Clean Air Act are exempt from the requirements of this section, provided that such change does not increase the actual hourly emissions of any pollutant regulated under this section above the actual hourly emissions achievable at that unit during the 5 years prior to the change.

(2) This exemption shall not apply to any new unit that:

(i) Is designated as a replacement for an existing unit;

(ii) Qualifies under section 409(b) of the Clean Air Act for an extension of an emission limitation compliance date under section 405 of the Clean Air Act; and

(iii) Is located at a different site than the existing unit.

(k) The installation, operation, cessation, or removal of a temporary clean coal technology demonstration project is exempt from the requirements of this section. A temporary clean coal control technology demonstration project, for the purposes of this section is a clean coal technology demonstration project that is operated for a period of 5 years or less, and which complies with the State implementation plan for the State in which the project is located and other requirements necessary to attain and maintain the national ambient air quality standards during the project and after it is terminated.

(l) The reactivation of a very clean coal-fired electric utility steam generating unit is exempt from the requirements of this section.

[40 FR 58419, Dec. 16, 1975, as amended at 43 FR 34347, Aug. 3, 1978; 45 FR 5617, Jan. 23, 1980; 57 FR 32339, July 21, 1992; 65 FR 61750, Oct. 17, 2000]

§60.15   Reconstruction.

(a) An existing facility, upon reconstruction, becomes an affected facility, irrespective of any change in emission rate.

(b) “Reconstruction” means the replacement of components of an existing facility to such an extent that:

(1) The fixed capital cost of the new components exceeds 50 percent of the fixed capital cost that would be required to construct a comparable entirely new facility, and

(2) It is technologically and economically feasible to meet the applicable standards set forth in this part.

(c) “Fixed capital cost” means the capital needed to provide all the depreciable components.

(d) If an owner or operator of an existing facility proposes to replace components, and the fixed capital cost of the new components exceeds 50 percent of the fixed capital cost that would be required to construct a comparable entirely new facility, he shall notify the Administrator of the proposed replacements. The notice must be postmarked 60 days (or as soon as practicable) before construction of the replacements is commenced and must include the following information:

(1) Name and address of the owner or operator.

(2) The location of the existing facility.

(3) A brief description of the existing facility and the components which are to be replaced.

(4) A description of the existing air pollution control equipment and the proposed air pollution control equipment.

(5) An estimate of the fixed capital cost of the replacements and of constructing a comparable entirely new facility.

(6) The estimated life of the existing facility after the replacements.

(7) A discussion of any economic or technical limitations the facility may have in complying with the applicable standards of performance after the proposed replacements.

(e) The Administrator will determine, within 30 days of the receipt of the notice required by paragraph (d) of this section and any additional information he may reasonably require, whether the proposed replacement constitutes reconstruction.

(f) The Administrator's determination under paragraph (e) shall be based on:

(1) The fixed capital cost of the replacements in comparison to the fixed capital cost that would be required to construct a comparable entirely new facility;

(2) The estimated life of the facility after the replacements compared to the life of a comparable entirely new facility;

(3) The extent to which the components being replaced cause or contribute to the emissions from the facility; and

(4) Any economic or technical limitations on compliance with applicable standards of performance which are inherent in the proposed replacements.

(g) Individual subparts of this part may include specific provisions which refine and delimit the concept of reconstruction set forth in this section.

[40 FR 58420, Dec. 16, 1975]

§60.16   Priority list.

Prioritized Major Source Categories

Priority Number1Source Category
1.Synthetic Organic Chemical Manufacturing Industry (SOCMI) and Volatile Organic Liquid Storage Vessels and Handling Equipment
   (a) SOCMI unit processes
   (b) Volatile organic liquid (VOL) storage vessels and handling equipment
   (c) SOCMI fugitive sources
   (d) SOCMI secondary sources
2.Industrial Surface Coating: Cans
3.Petroleum Refineries: Fugitive Sources
4.Industrial Surface Coating: Paper
5.Dry Cleaning
   (a) Perchloroethylene
   (b) Petroleum solvent
6.Graphic Arts
7.Polymers and Resins: Acrylic Resins
8.Mineral Wool (Deleted)
9.Stationary Internal Combustion Engines
10.Industrial Surface Coating: Fabric
11.Industrial-Commercial-Institutional Steam Generating Units.
12.Incineration: Non-Municipal (Deleted)
13.Non-Metallic Mineral Processing
14.Metallic Mineral Processing
15.Secondary Copper (Deleted)
16.Phosphate Rock Preparation
17.Foundries: Steel and Gray Iron
18.Polymers and Resins: Polyethylene
19.Charcoal Production
20.Synthetic Rubber
   (a) Tire manufacture
   (b) SBR production
21.Vegetable Oil
22.Industrial Surface Coating: Metal Coil
23.Petroleum Transportation and Marketing
24.By-Product Coke Ovens
25.Synthetic Fibers
26.Plywood Manufacture
27.Industrial Surface Coating: Automobiles
28.Industrial Surface Coating: Large Appliances
29.Crude Oil and Natural Gas Production
30.Secondary Aluminum
31.Potash (Deleted)
32.Lightweight Aggregate Industry: Clay, Shale, and Slate2
33.Glass
34.Gypsum
35.Sodium Carbonate
36.Secondary Zinc (Deleted)
37.Polymers and Resins: Phenolic
38.Polymers and Resins: Urea-Melamine
39.Ammonia (Deleted)
40.Polymers and Resins: Polystyrene
41.Polymers and Resins: ABS-SAN Resins
42.Fiberglass
43.Polymers and Resins: Polypropylene
44.Textile Processing
45.Asphalt Processing and Asphalt Roofing Manufacture
46.Brick and Related Clay Products
47.Ceramic Clay Manufacturing (Deleted)
48.Ammonium Nitrate Fertilizer
49.Castable Refractories (Deleted)
50.Borax and Boric Acid (Deleted)
51.Polymers and Resins: Polyester Resins
52.Ammonium Sulfate
53.Starch
54.Perlite
55.Phosphoric Acid: Thermal Process (Deleted)
56.Uranium Refining
57.Animal Feed Defluorination (Deleted)
58.Urea (for fertilizer and polymers)
59.Detergent (Deleted)
Other Source Categories
Lead acid battery manufacture3
Organic solvent cleaning3
Industrial surface coating: metal furniture3
Stationary gas turbines4
Municipal solid waste landfills4
   

1Low numbers have highest priority, e.g., No. 1 is high priority, No. 59 is low priority.

2Formerly titled “Sintering: Clay and Fly Ash”.

3Minor source category, but included on list since an NSPS is being developed for that source category.

4Not prioritized, since an NSPS for this major source category has already been promulgated.

[47 FR 951, Jan. 8, 1982, as amended at 47 FR 31876, July 23, 1982; 51 FR 42796, Nov. 25, 1986; 52 FR 11428, Apr. 8, 1987; 61 FR 9919, Mar. 12, 1996]

§60.17   Incorporations by reference.

(a) Certain material is incorporated by reference into this part with the approval of the Director of the Federal Register under 5 U.S.C. 552(a) and 1 CFR part 51. To enforce any edition other than that specified in this section, the EPA must publish notice of change in the Federal Register and the material must be available to the public. All approved material is available for inspection at the Air and Radiation Docket and Information Center, U.S. EPA, 401 M St. SW., Washington, DC, telephone number 202-566, and is available from the sources listed below. It is also available for inspection at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030 or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

(b) American Gas Association, available through ILI Infodisk, 610 Winters Avenue, Paramus, New Jersey 07652:

(1) American Gas Association Report No. 3: Orifice Metering for Natural Gas and Other Related Hydrocarbon Fluids, Part 1: General Equations and Uncertainty Guidelines (1990), IBR approved for §60.107a(d).

(2) American Gas Association Report No. 3: Orifice Metering for Natural Gas and Other Related Hydrocarbon Fluids, Part 2: Specification and Installation Requirements (2000), IBR approved for §60.107a(d).

(3) American Gas Association Report No. 11: Measurement of Natural Gas by Coriolis Meter (2003), IBR approved for §60.107a(d).

(4) American Gas Association Transmission Measurement Committee Report No. 7: Measurement of Gas by Turbine Meters (Revised February 2006), IBR approved for §60.107a(d).

(c) American Hospital Association (AHA) Service, Inc., Post Office Box 92683, Chicago, Illinois 60675-2683. You may inspect a copy at the EPA's Air and Radiation Docket and Information Center (Docket A-91-61, Item IV-J-124), Room M-1500, 1200 Pennsylvania Ave. NW., Washington, DC 20460.

(1) An Ounce of Prevention: Waste Reduction Strategies for Health Care Facilities. American Society for Health Care Environmental Services of the American Hospital Association. Chicago, Illinois. 1993. AHA Catalog No. 057007. ISBN 0-87258-673-5. IBR approved for §§60.35e and 60.55c.

(2) [Reserved]

(d) American Petroleum Institute (API), 1220 L Street NW., Washington, DC 20005.

(1) API Publication 2517, Evaporation Loss from External Floating Roof Tanks, Second Edition, February 1980, IBR approved for §§60.111(i), 60.111a(f), and 60.116b(e).

(2) API Manual of Petroleum Measurement Standards, Chapter 22—Testing Protocol, Section 2—Differential Pressure Flow Measurement Devices, First Edition, August 2005, IBR approved for §60.107a(d).

(e) American Public Health Association, 1015 18th Street NW., Washington, DC 20036.

(1) “Standard Methods for the Examination of Water and Wastewater,” 16th edition, 1985. Method 303F: “Determination of Mercury by the Cold Vapor Technique.” Incorporated by reference for appendix A-8 to part 60, Method 29, §§9.2.3, 10.3, and 11.1.3.

(2) 2540 G. Total, Fixed, and Volatile Solids in Solid and Semisolid Samples, in Standard Methods for the Examination of Water and Wastewater, 20th Edition, 1998, IBR approved for §60.154(b).

(f) The following material is available for purchase from the American Society of Mechanical Engineers (ASME), Two Park Avenue, New York, NY 10016-5990, Telephone (800) 843-2763, and is also available at the following Web site: http://www.asme.org.

(1) ASME Interim Supplement 19.5 on Instruments and Apparatus: Application, Part II of Fluid Meters, 6th Edition (1971), IBR approved for §§60.58a(h), 60.58b(i), 60.1320(a), and 60.1810(a).

(2) ASME MFC-3M-2004, Measurement of Fluid Flow in Pipes Using Orifice, Nozzle, and Venturi, IBR approved for §60.107a(d).

(3) ASME/ANSI MFC-4M-1986 (Reaffirmed 2008), Measurement of Gas Flow by Turbine Meters, IBR approved for §60.107a(d).

(4) ASME/ANSI MFC-5M-1985 (Reaffirmed 2006), Measurement of Liquid Flow in Closed Conduits Using Transit-Time Ultrasonic Flowmeters, IBR approved for §60.107a(d).

(5) ASME MFC-6M-1998 (Reaffirmed 2005), Measurement of Fluid Flow in Pipes Using Vortex Flowmeters, IBR approved for §60.107a(d).

(6) ASME/ANSI MFC-7M-1987 (Reaffirmed 2006), Measurement of Gas Flow by Means of Critical Flow Venturi Nozzles, IBR approved for §60.107a(d).

(7) ASME/ANSI MFC-9M-1988 (Reaffirmed 2006), Measurement of Liquid Flow in Closed Conduits by Weighing Method, IBR approved for §60.107a(d).

(8) ASME MFC-11M-2006, Measurement of Fluid Flow by Means of Coriolis Mass Flowmeters, IBR approved for §60.107a(d).

(9) ASME MFC-14M-2003, Measurement of Fluid Flow Using Small Bore Precision Orifice Meters, IBR approved for §60.107a(d).

(10) ASME MFC-16-2007, Measurement of Liquid Flow in Closed Conduits with Electromagnetic Flowmeters, IBR approved for §60.107a(d).

(11) ASME MFC-18M-2001, Measurement of Fluid Flow Using Variable Area Meters, IBR approved for §60.107a(d).

(12) ASME MFC-22-2007, Measurement of Liquid by Turbine Flowmeters, IBR approved for §60.107a(d).

(13) ASME PTC 4.1-1964 (Reaffirmed 1991), Power Test Codes: Test Code for Steam Generating Units (with 1968 and 1969 Addenda), IBR approved for §§60.46b, 60.58a(h), 60.58b(i), 60.1320(a), and 60.1810(a).

(14) ASME/ANSI PTC 19.10-1981, Flue and Exhaust Gas Analyses [Part 10, Instruments and Apparatus], (Issued August 31, 1981), IBR approved for §§60.56c(b), 60.63(f), 60.106(e), 60.104a(d), (h), (i), and (j), 60.105a(d), (f), and (g), §60.106a(a), §60.107a(a), (c), and (d), tables 1 and 3 to subpart EEEE, tables 2 and 4 to subpart FFFF, table 2 to subpart JJJJ, §60.285a(f), §§60.4415(a), 60.2145(s) and (t), 60.2710(s) (t), and (w), 60.2730(q), 60.4900(b), 60.5220(b), tables 1 and 2 to subpart LLLL, tables 2 and 3 to subpart MMMM, §§60.5406(c) and 60.5413(b).

(15) ASME QRO-1-1994, Standard for the Qualification and Certification of Resource Recovery Facility Operators, IBR approved for §§60.54b(a) and (b), 60.56a, 60.1185(a) and (c), and 60.1675(a) and (c).

(g) American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428-2959; also available through ProQuest, 300 North Zeeb Road, Ann Arbor, MI 48106.

(1) ASTM A99-76, Standard Specification for Ferromanganese, IBR approved for §60.261.

(2) ASTM A99-82 (Reapproved 1987), Standard Specification for Ferromanganese, IBR approved for §60.261.

(3) ASTM A100-69, Standard Specification for Ferrosilicon, IBR approved for §60.261.

(4) ASTM A100-74, Standard Specification for Ferrosilicon, IBR approved for §60.261.

(5) ASTM A100-93, Standard Specification for Ferrosilicon, IBR approved for §60.261.

(6) ASTM A101-73, Standard Specification for Ferrochromium, IBR approved for §60.261.

(7) ASTM A101-93, Standard Specification for Ferrochromium, IBR approved for §60.261.

(8) ASTM A482-76, Standard Specification for Ferrochromesilicon, IBR approved for §60.261.

(9) ASTM A482-93, Standard Specification for Ferrochromesilicon, IBR approved for §60.261.

(10) ASTM A483-64, Standard Specification for Silicomanganese, IBR approved for §60.261.

(11) ASTM A483-74 (Reapproved 1988), Standard Specification for Silicomanganese, IBR approved for §60.261.

(12) ASTM A495-76, Standard Specification for Calcium-Silicon and Calcium Manganese-Silicon, IBR approved for §60.261.

(13) ASTM A495-94, Standard Specification for Calcium-Silicon and Calcium Manganese-Silicon, IBR approved for §60.261.

(14) ASTM D86-78, Distillation of Petroleum Products, IBR approved for §§60.562-2(d), 60.593(d), 60.593a(d), 60.633(h).

(15) ASTM D86-82, Distillation of Petroleum Products, IBR approved for §§60.562-2(d), 60.593(d), 60.593a(d), 60.633(h).

(16) ASTM D86-90, Distillation of Petroleum Products, IBR approved for §§60.562-2(d), 60.593(d), 60.593a(d), 60.633(h).

(17) ASTM D86-93, Distillation of Petroleum Products, IBR approved for §§60.562-2(d), 60.593(d), 60.593a(d), 60.633(h).

(18) ASTM D86-95, Distillation of Petroleum Products, IBR approved for §§60.562-2(d), 60.593(d), 60.593a(d), 60.633(h).

(19) ASTM D86-96, Distillation of Petroleum Products, (Approved April 10, 1996), IBR approved for §§60.562-2(d), 60.593(d), 60.593a(d), 60.633(h), and 60.5401(f).

(20) ASTM D129-64, Standard Test Method for Sulfur in Petroleum Products (General Bomb Method), IBR approved for §§60.106(j) and appendix A-7 to part 60: Method 19, Section 12.5.2.2.3.

(21) ASTM D129-78, Standard Test Method for Sulfur in Petroleum Products (General Bomb Method), IBR approved for §§60.106(j) and appendix A-7 to part 60: Method 19, Section 12.5.2.2.3.

(22) ASTM D129-95, Standard Test Method for Sulfur in Petroleum Products (General Bomb Method), IBR approved for §§60.106(j) and appendix A-7 to part 60: Method 19, Section 12.5.2.2.3.

(23) ASTM D129-00, Standard Test Method for Sulfur in Petroleum Products (General Bomb Method), IBR approved for §60.335(b).

(24) ASTM D129-00 (Reapproved 2005), Standard Test Method for Sulfur in Petroleum Products (General Bomb Method), IBR approved for §60.4415(a).

(25) ASTM D240-76, Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter, IBR approved for §§60.46(c), 60.296(b), and appendix A-7 to part 60: Method 19, Section 12.5.2.2.3.

(26) ASTM D240-92, Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter, IBR approved for §§60.46(c), 60.296(b), and appendix A-7: Method 19, Section 12.5.2.2.3.

(27) ASTM D240-02 (Reapproved 2007), Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter, (Approved May 1, 2007), IBR approved for §60.107a(d).

(28) ASTM D270-65, Standard Method of Sampling Petroleum and Petroleum Products, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.2.1.

(29) ASTM D270-75, Standard Method of Sampling Petroleum and Petroleum Products, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.2.1.

(30) ASTM D323-82, Test Method for Vapor Pressure of Petroleum Products (Reid Method), IBR approved for §§60.111(l), 60.111a(g), 60.111b, and 60.116b(f).

(31) ASTM D323-94, Test Method for Vapor Pressure of Petroleum Products (Reid Method), IBR approved for §§60.111(l), 60.111a(g), 60.111b, and 60.116b(f).

(32) ASTM D388-77, Standard Specification for Classification of Coals by Rank, IBR approved for §§60.41, 60.45(f), 60.41Da, 60.41b, 60.41c, and 60.251.

(33) ASTM D388-90, Standard Specification for Classification of Coals by Rank, IBR approved for §§60.41, 60.45(f), 60.41Da, 60.41b, 60.41c, and 60.251.

(34) ASTM D388-91, Standard Specification for Classification of Coals by Rank, IBR approved for §§60.41, 60.45(f), 60.41Da, 60.41b, 60.41c, and 60.251.

(35) ASTM D388-95, Standard Specification for Classification of Coals by Rank, IBR approved for §§60.41, 60.45(f), 60.41Da, 60.41b, 60.41c, and 60.251.

(36) ASTM D388-98a, Standard Specification for Classification of Coals by Rank, IBR approved for §§60.41, 60.45(f), 60.41Da, 60.41b, 60.41c, and 60.251.

(37) ASTM D388-99 (Reapproved 2004)ε,1 Standard Specification for Classification of Coals by Rank, IBR approved for §§60.41, 60.45(f), 60.41Da, 60.41b, 60.41c, and 60.251.

(38) ASTM D396-78, Standard Specification for Fuel Oils, IBR approved for §§60.41b, 60.41c, 60.111(b), and 60.111a(b).

(39) ASTM D396-89, Standard Specification for Fuel Oils, IBR approved for §§60.41b, 60.41c, 60.111(b), and 60.111a(b).

(40) ASTM D396-90, Standard Specification for Fuel Oils, IBR approved for §§60.41b, 60.41c, 60.111(b), and 60.111a(b).

(41) ASTM D396-92, Standard Specification for Fuel Oils, IBR approved for §§60.41b, 60.41c, 60.111(b), and 60.111a(b).

(42) ASTM D396-98, Standard Specification for Fuel Oils, IBR approved for §§60.41b, 60.41c, 60.111(b), and 60.111a(b).

(43) ASTM D975-78, Standard Specification for Diesel Fuel Oils, IBR approved for §§60.111(b) and 60.111a(b).

(44) ASTM D975-96, Standard Specification for Diesel Fuel Oils, IBR approved for §§60.111(b) and 60.111a(b).

(45) ASTM D975-98a, Standard Specification for Diesel Fuel Oils, IBR approved for §§60.111(b) and 60.111a(b).

(46) ASTM D975-08a, Standard Specification for Diesel Fuel Oils, IBR approved for §§60.41b and 60.41c.

(47) ASTM D1072-80, Standard Test Method for Total Sulfur in Fuel Gases, IBR approved for §60.335(b).

(48) ASTM D1072-90 (Reapproved 1994), Standard Test Method for Total Sulfur in Fuel Gases, IBR approved for §60.335(b).

(49) ASTM D1072-90 (Reapproved 1999), Standard Test Method for Total Sulfur in Fuel Gases, IBR approved for §60.4415(a).

(50) ASTM D1137-53, Standard Method for Analysis of Natural Gases and Related Types of Gaseous Mixtures by the Mass Spectrometer, IBR approved for §60.45(f).

(51) ASTM D1137-75, Standard Method for Analysis of Natural Gases and Related Types of Gaseous Mixtures by the Mass Spectrometer, IBR approved for §60.45(f).

(52) ASTM D1193-77, Standard Specification for Reagent Water, IBR approved for appendix A-3 to part 60: Method 5, Section 7.1.3; Method 5E, Section 7.2.1; Method 5F, Section 7.2.1; appendix A-4 to part 60: Method 6, Section 7.1.1; Method 7, Section 7.1.1; Method 7C, Section 7.1.1; Method 7D, Section 7.1.1; Method 10A, Section 7.1.1; appendix A-5 to part 60: Method 11, Section 7.1.3; Method 12, Section 7.1.3; Method 13A, Section 7.1.2; appendix A-8 to part 60: Method 26, Section 7.1.2; Method 26A, Section 7.1.2; and Method 29, Section 7.2.2.

(53) ASTM D1193-91, Standard Specification for Reagent Water, IBR approved for appendix A-3 to part 60: Method 5, Section 7.1.3; Method 5E, Section 7.2.1; Method 5F, Section 7.2.1; appendix A-4 to part 60: Method 6, Section 7.1.1; Method 7, Section 7.1.1; Method 7C, Section 7.1.1; Method 7D, Section 7.1.1; Method 10A, Section 7.1.1; appendix A-5 to part 60: Method 11, Section 7.1.3; Method 12, Section 7.1.3; Method 13A, Section 7.1.2; appendix A-8 to part 60: Method 26, Section 7.1.2; Method 26A, Section 7.1.2; and Method 29, Section 7.2.2.

(54) ASTM D1266-87, Standard Test Method for Sulfur in Petroleum Products (Lamp Method), IBR approved for §§60.106(j) and 60.335(b).

(55) ASTM D1266-91, Standard Test Method for Sulfur in Petroleum Products (Lamp Method), IBR approved for §§60.106(j) and 60.335(b).

(56) ASTM D1266-98, Standard Test Method for Sulfur in Petroleum Products (Lamp Method), IBR approved for §§60.106(j) and 60.335(b).

(57) ASTM D1266-98 (Reapproved 2003)ε,1 Standard Test Method for Sulfur in Petroleum Products (Lamp Method), IBR approved for §60.4415(a).

(58) ASTM D1475-60 (Reapproved 1980), Standard Test Method for Density of Paint, Varnish Lacquer, and Related Products, IBR approved for §60.435(d), appendix A-8 to part 60: Method 24, Section 6.1; and Method 24A, Sections 6.5 and 7.1.

(59) ASTM D1475-90, Standard Test Method for Density of Paint, Varnish Lacquer, and Related Products, IBR approved for §60.435(d), appendix A-8 to part 60: Method 24, Section 6.1; and Method 24A, §§6.5 and 7.1.

(60) ASTM D1552-83, Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method), IBR approved for §§60.106(j), 60.335(b), and appendix A-7 to part 60: Method 19, Section 12.5.2.2.3.

(61) ASTM D1552-95, Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method), IBR approved for §§60.106(j), 60.335(b), and appendix A-7 to part 60: Method 19, Section 12.5.2.2.3.

(62) ASTM D1552-01, Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method), IBR approved for §§60.106(j), 60.335(b), and appendix A-7 to part 60: Method 19, Section 12.5.2.2.3.

(63) ASTM D1552-03, Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method), IBR approved for §60.4415(a).

(64) ASTM D1826-77, Standard Test Method for Calorific Value of Gases in Natural Gas Range by Continuous Recording Calorimeter, IBR approved for §§60.45(f), 60.46(c), 60.296(b), and appendix A-7 to part 60: Method 19, Section 12.3.2.4.

(65) ASTM D1826-94, Standard Test Method for Calorific Value of Gases in Natural Gas Range by Continuous Recording Calorimeter, IBR approved for §§60.45(f), 60.46(c), 60.296(b), and appendix A-7 to part 60: Method 19, Section 12.3.2.4.

(66) ASTM D1826-94 (Reapproved 2003), Standard Test Method for Calorific (Heating) Value of Gases in Natural Gas Range by Continuous Recording Calorimeter, (Approved May 10, 2003), IBR approved for §60.107a(d).

(67) ASTM D1835-87, Standard Specification for Liquefied Petroleum (LP) Gases, IBR approved for §§60.41Da, 60.41b, and 60.41c.

(68) ASTM D1835-91, Standard Specification for Liquefied Petroleum (LP) Gases, IBR approved for §§60.41Da, 60.41b, and 60.41c.

(69) ASTM D1835-97, Standard Specification for Liquefied Petroleum (LP) Gases, IBR approved for §§60.41Da, 60.41b, and 60.41c.

(70) ASTM D1835-03a, Standard Specification for Liquefied Petroleum (LP) Gases, IBR approved for §§60.41Da, 60.41b, and 60.41c.

(71) ASTM D1945-64, Standard Method for Analysis of Natural Gas by Gas Chromatography, IBR approved for §60.45(f).

(72) ASTM D1945-76, Standard Method for Analysis of Natural Gas by Gas Chromatography, IBR approved for §60.45(f).

(73) ASTM D1945-91, Standard Method for Analysis of Natural Gas by Gas Chromatography, IBR approved for §60.45(f).

(74) ASTM D1945-96, Standard Method for Analysis of Natural Gas by Gas Chromatography, IBR approved for §60.45(f).

(75) ASTM D1945-03 (Reapproved 2010), Standard Method for Analysis of Natural Gas by Gas Chromatography, (Approved January 1, 2010), IBR approved for §§60.107a(d) and 60.5413(d).

(76) ASTM D1946-77, Standard Method for Analysis of Reformed Gas by Gas Chromatography, IBR approved for §§60.18(f), 60.45(f), 60.564(f), 60.614(e), 60.664(e), and 60.704(d).

(77) ASTM D1946-90 (Reapproved 1994), Standard Method for Analysis of Reformed Gas by Gas Chromatography, IBR approved for §§60.18(f), 60.45(f), 60.564(f), 60.614(e), 60.664(e), and 60.704(d).

(78) ASTM D1946-90 (Reapproved 2006), Standard Method for Analysis of Reformed Gas by Gas Chromatography, (Approved June 1, 2006), IBR approved for §60.107a(d).

(79) ASTM D2013-72, Standard Method of Preparing Coal Samples for Analysis, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(80) ASTM D2013-86, Standard Method of Preparing Coal Samples for Analysis, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(81) ASTM D2015-77 (Reapproved 1978), Standard Test Method for Gross Calorific Value of Solid Fuel by the Adiabatic Bomb Calorimeter, IBR approved for §§60.45(f), 60.46(c), and appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(82) ASTM D2015-96, Standard Test Method for Gross Calorific Value of Solid Fuel by the Adiabatic Bomb Calorimeter, IBR approved for §§60.45(f), 60.46(c), and appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(83) ASTM D2016-74, Standard Test Methods for Moisture Content of Wood, IBR approved for appendix A-8 to part 60: Method 28, Section 16.1.1.

(84) ASTM D2016-83, Standard Test Methods for Moisture Content of Wood, IBR approved for appendix A-8 to part 60: Method 28, Section 16.1.1.

(85) ASTM D2234-76, Standard Methods for Collection of a Gross Sample of Coal, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.1.

(86) ASTM D2234-96, Standard Methods for Collection of a Gross Sample of Coal, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.1.

(87) ASTM D2234-97b, Standard Methods for Collection of a Gross Sample of Coal, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.1.

(88) ASTM D2234-98, Standard Methods for Collection of a Gross Sample of Coal, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.1.

(89) ASTM D2369-81, Standard Test Method for Volatile Content of Coatings, IBR approved for appendix A-8 to part 60: Method 24, Section 6.2.

(90) ASTM D2369-87, Standard Test Method for Volatile Content of Coatings, IBR approved for appendix A-8 to part 60: Method 24, Section 6.2.

(91) ASTM D2369-90, Standard Test Method for Volatile Content of Coatings, IBR approved for appendix A-8 to part 60: Method 24, Section 6.2.

(92) ASTM D2369-92, Standard Test Method for Volatile Content of Coatings, IBR approved for appendix A-8 to part 60: Method 24, Section 6.2.

(93) ASTM D2369-93, Standard Test Method for Volatile Content of Coatings, IBR approved for appendix A-8 to part 60: Method 24, Section 6.2.

(94) ASTM D2369-95, Standard Test Method for Volatile Content of Coatings, IBR approved for appendix A-8 to part 60: Method 24, Section 6.2.

(95) ASTM D2382-76, Heat of Combustion of Hydrocarbon Fuels by Bomb Calorimeter (High-Precision Method), IBR approved for §§60.18(f), 60.485(g), 60.485a(g), 60.564(f), 60.614(e), 60.664(e), and 60.704(d).

(96) ASTM D2382-88, Heat of Combustion of Hydrocarbon Fuels by Bomb Calorimeter (High-Precision Method), IBR approved for §§60.18(f), 60.485(g), 60.485a(g), 60.564(f), 60.614(e), 60.664(e), and 60.704(d).

(97) ASTM D2504-67, Noncondensable Gases in C3 and Lighter Hydrocarbon Products by Gas Chromatography, IBR approved for §§60.485(g) and 60.485a(g).

(98) ASTM D2504-77, Noncondensable Gases in C3 and Lighter Hydrocarbon Products by Gas Chromatography, IBR approved for §§60.485(g) and 60.485a(g).

(99) ASTM D2504-88 (Reapproved 1993), Noncondensable Gases in C3 and Lighter Hydrocarbon Products by Gas Chromatography, IBR approved for §§60.485(g) and 60.485a(g).

(100) ASTM D2584-68(Reapproved 1985), Standard Test Method for Ignition Loss of Cured Reinforced Resins, IBR approved for §60.685(c).

(101) ASTM D2584-94, Standard Test Method for Ignition Loss of Cured Reinforced Resins, IBR approved for §60.685(c).

(102) ASTM D2597-94 (Reapproved 1999), Standard Test Method for Analysis of Demethanized Hydrocarbon Liquid Mixtures Containing Nitrogen and Carbon Dioxide by Gas Chromatography, IBR approved for §60.335(b).

(103) ASTM D2622-87, Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-Ray Fluorescence Spectrometry, IBR approved for §§60.106(j) and 60.335(b).

(104) ASTM D2622-94, Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-Ray Fluorescence Spectrometry, IBR approved for §§60.106(j) and 60.335(b).

(105) ASTM D2622-98, Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-Ray Fluorescence Spectrometry, IBR approved for §§60.106(j) and 60.335(b).

(106) ASTM D2622-05, Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-Ray Fluorescence Spectrometry, IBR approved for §60.4415(a).

(107) ASTM D2879-83Test Method for Vapor Pressure-Temperature Relationship and Initial Decomposition Temperature of Liquids by Isoteniscope, IBR approved for §§60.111b(f)(3), 60.116b(e), 60.116b(f), 60.485(e), and 60.485a(e).

(108) ASTM D2879-96, Test Method for Vapor Pressure-Temperature Relationship and Initial Decomposition Temperature of Liquids by Isoteniscope, IBR approved for §§60.111b(f)(3), 60.116b(e), 60.116b(f), 60.485(e), and 60.485a(e).

(109) ASTM D2879-97, Test Method for Vapor Pressure-Temperature Relationship and Initial Decomposition Temperature of Liquids by Isoteniscope, IBR approved for §§60.111b(f)(3), 60.116b(e), 60.116b(f), 60.485(e), and 60.485a(e).

(110) ASTM D2880-78, Standard Specification for Gas Turbine Fuel Oils, IBR approved for §§60.111(b), 60.111a(b), and 60.335(d).

(111) ASTM D2880-96, Standard Specification for Gas Turbine Fuel Oils, IBR approved for §§60.111(b), 60.111a(b), and 60.335(d).

(112) ASTM D2908-74, Standard Practice for Measuring Volatile Organic Matter in Water by Aqueous-Injection Gas Chromatography, IBR approved for §60.564(j).

(113) ASTM D2908-91, Standard Practice for Measuring Volatile Organic Matter in Water by Aqueous-Injection Gas Chromatography, IBR approved for §60.564(j).

(114) ASTM D2986-71, Standard Method for Evaluation of Air, Assay Media by the Monodisperse DOP (Dioctyl Phthalate) Smoke Test, IBR approved for appendix A-3 to part 60: Method 5, Section 7.1.1; appendix A-5 to part 60: Method 12, Section 7.1.1; and Method 13A, Section 7.1.1.2.

(115) ASTM D2986-78, Standard Method for Evaluation of Air, Assay Media by the Monodisperse DOP (Dioctyl Phthalate) Smoke Test, IBR approved for appendix A-3 to part 60: Method 5, Section 7.1.1; appendix A-5 to part 60: Method 12, Section 7.1.1; and Method 13A, Section 7.1.1.2.

(116) ASTM D2986-95a, Standard Method for Evaluation of Air, Assay Media by the Monodisperse DOP (Dioctyl Phthalate) Smoke Test, IBR approved for appendix A-3 to part 60: Method 5, Section 7.1.1; appendix A-5 to part 60: Method 12, Section 7.1.1; and Method 13A, Section 7.1.1.2.

(117) ASTM D3173-73, Standard Test Method for Moisture in the Analysis Sample of Coal and Coke, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(118) ASTM D3173-87, Standard Test Method for Moisture in the Analysis Sample of Coal and Coke, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(119) ASTM D3176-74, Standard Method for Ultimate Analysis of Coal and Coke, IBR approved for §60.45(f)(5)(i) and appendix A-7 to part 60: Method 19, Section 12.3.2.3.

(120) ASTM D3176-89, Standard Method for Ultimate Analysis of Coal and Coke, IBR approved for §60.45(f)(5)(i) and appendix A-7 to part 60: Method 19, Section 12.3.2.3.

(121) ASTM D3177-75, Standard Test Method for Total Sulfur in the Analysis Sample of Coal and Coke, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(122) ASTM D3177-89, Standard Test Method for Total Sulfur in the Analysis Sample of Coal and Coke, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(123) ASTM D3178-73 (Reapproved 1979), Standard Test Methods for Carbon and Hydrogen in the Analysis Sample of Coal and Coke, IBR approved for §60.45(f).

(124) ASTM D3178-89, Standard Test Methods for Carbon and Hydrogen in the Analysis Sample of Coal and Coke, IBR approved for §60.45(f).

(125) ASTM D3246-81, Standard Test Method for Sulfur in Petroleum Gas by Oxidative Microcoulometry, IBR approved for §60.335(b).

(126) ASTM D3246-92, Standard Test Method for Sulfur in Petroleum Gas by Oxidative Microcoulometry, IBR approved for §60.335(b).

(127) ASTM D3246-96, Standard Test Method for Sulfur in Petroleum Gas by Oxidative Microcoulometry, IBR approved for §60.335(b).

(128) ASTM D3246-05, Standard Test Method for Sulfur in Petroleum Gas by Oxidative Microcoulometry, IBR approved for §60.4415(a)(1).

(129) ASTM D3270-73T, Standard Test Methods for Analysis for Fluoride Content of the Atmosphere and Plant Tissues (Semiautomated Method), IBR approved for appendix A-5 to part 60: Method 13A, Section 16.1.

(130) ASTM D3270-80, Standard Test Methods for Analysis for Fluoride Content of the Atmosphere and Plant Tissues (Semiautomated Method), IBR approved for appendix A-5 to part 60: Method 13A, Section 16.1.

(131) ASTM D3270-91, Standard Test Methods for Analysis for Fluoride Content of the Atmosphere and Plant Tissues (Semiautomated Method), IBR approved for appendix A-5 to part 60: Method 13A, Section 16.1.

(132) ASTM D3270-95, Standard Test Methods for Analysis for Fluoride Content of the Atmosphere and Plant Tissues (Semiautomated Method), IBR approved for appendix A-5 to part 60: Method 13A, Section 16.1.

(133) ASTM D3286-85, Standard Test Method for Gross Calorific Value of Coal and Coke by the Isoperibol Bomb Calorimeter, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(134) ASTM D3286-96, Standard Test Method for Gross Calorific Value of Coal and Coke by the Isoperibol Bomb Calorimeter, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(135) ASTM D3370-76, Standard Practices for Sampling Water, IBR approved for §60.564(j).

(136) ASTM D3370-95a, Standard Practices for Sampling Water, IBR approved for §60.564(j).

(137) ASTM D3588-98 (Reapproved 2003), Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels, (Approved May 10, 2003), IBR approved for §§60.107a(d) and 60.5413(d).

(138) ASTM D3699-08, Standard Specification for Kerosine, including Appendix X1, (Approved September 1, 2008), IBR approved for §§60.41b and 60.41c.

(139) ASTM D3792-79, Standard Test Method for Water Content of Water-Reducible Paints by Direct Injection into a Gas Chromatograph, IBR approved for appendix A-7 to part 60: Method 24, Section 6.3.

(140) ASTM D3792-91, Standard Test Method for Water Content of Water-Reducible Paints by Direct Injection into a Gas Chromatograph, IBR approved for appendix A-7 to part 60: Method 24, Section 6.3.

(141) ASTM D4017-81, Standard Test Method for Water in Paints and Paint Materials by the Karl Fischer Titration Method, IBR approved for appendix A-7 to part 60: Method 24, Section 6.4.

(142) ASTM D4017-90, Standard Test Method for Water in Paints and Paint Materials by the Karl Fischer Titration Method, IBR approved for appendix A-7 to part 60: Method 24, Section 6.4.

(143) ASTM D4017-96a, Standard Test Method for Water in Paints and Paint Materials by the Karl Fischer Titration Method, IBR approved for appendix A-7 to part 60: Method 24, Section 6.4.

(144) ASTM D4057-81, Standard Practice for Manual Sampling of Petroleum and Petroleum Products, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.2.3.

(145) ASTM D4057-95, Standard Practice for Manual Sampling of Petroleum and Petroleum Products, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.2.3.

(146) ASTM D4057-95 (Reapproved 2000), Standard Practice for Manual Sampling of Petroleum and Petroleum Products, IBR approved for §60.4415(a).

(147) ASTM D4084-82, Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method), IBR approved for §60.334(h).

(148) ASTM D4084-94, Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method), IBR approved for §60.334(h).

(149) ASTM D4084-05, Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method), IBR approved for §§60.4360 and 60.4415(a).

(150) ASTM D4177-95, Standard Practice for Automatic Sampling of Petroleum and Petroleum Products, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.2.1.

(151) ASTM D4177-95 (Reapproved 2000), Standard Practice for Automatic Sampling of Petroleum and Petroleum Products, IBR approved for §60.4415(a).

(152) ASTM D4239-85, Standard Test Methods for Sulfur in the Analysis Sample of Coal and Coke Using High Temperature Tube Furnace Combustion Methods, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(153) ASTM D4239-94, Standard Test Methods for Sulfur in the Analysis Sample of Coal and Coke Using High Temperature Tube Furnace Combustion Methods, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(154) ASTM D4239-97, Standard Test Methods for Sulfur in the Analysis Sample of Coal and Coke Using High Temperature Tube Furnace Combustion Methods, IBR approved for appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(155) ASTM D4294-02, Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry, IBR approved for §60.335(b).

(156) ASTM D4294-03, Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry, IBR approved for §60.4415(a).

(157) ASTM D4442-84, Standard Test Methods for Direct Moisture Content Measurement in Wood and Wood-base Materials, IBR approved for appendix A-8 to part 60: Method 28, Section 16.1.1.

(158) ASTM D4442-92, Standard Test Methods for Direct Moisture Content Measurement in Wood and Wood-base Materials, IBR approved for appendix A-8 to part 60: Method 28, Section 16.1.1.

(159) ASTM D4444-92, Standard Test Methods for Use and Calibration of Hand-Held Moisture Meters, IBR approved for appendix A-8 to part 60: Method 28, Section 16.1.1.

(160) ASTM D4457-85 (Reapproved 1991), Test Method for Determination of Dichloromethane and 1,1,1-Trichloroethane in Paints and Coatings by Direct Injection into a Gas Chromatograph, IBR approved for appendix A-7 to part 60: Method 24, Section 6.5.

(161) ASTM D4468-85 (Reapproved 2000), Standard Test Method for Total Sulfur in Gaseous Fuels by Hydrogenolysis and Rateometric Colorimetry, IBR approved for §§60.335(b) and 60.4415(a).

(162) ASTM D4468-85 (Reapproved 2006), Standard Test Method for Total Sulfur in Gaseous Fuels by Hydrogenolysis and Rateometric Colorimetry, (Approved June 1, 2006), IBR approved for §60.107a(e).

(163) ASTM D4629-02, Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection, IBR approved for §§60.49b(e) and 60.335(b).

(164) ASTM D4809-95, Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method), IBR approved for §§60.18(f), 60.485(g), 60.485a(g), 60.564(f), 60.614(d), 60.664(e), and 60.704(d).

(165) ASTM D4809-06, Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method), (Approved December 1, 2006), IBR approved for §60.107a(d).

(166) ASTM D4810-88 (Reapproved 1999), Standard Test Method for Hydrogen Sulfide in Natural Gas Using Length of Stain Detector Tubes, IBR approved for §§60.4360 and 60.4415(a).

(167) ASTM D4891-89 (Reapproved 2006) Standard Test Method for Heating Value of Gases in Natural Gas Range by Stoichiometric Combustion, (Approved June 1, 2006), IBR approved for §§60.107a(d) and 60.5413(d).

(168) ASTM D5287-97 (Reapproved 2002), Standard Practice for Automatic Sampling of Gaseous Fuels, IBR approved for §60.4415(a).

(169) ASTM D5403-93, Standard Test Methods for Volatile Content of Radiation Curable Materials, IBR approved for appendix A-7 to part 60: Method 24, Section 6.6.

(170) ASTM D5453-00, Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence, IBR approved for §60.335(b).

(171) ASTM D5453-05, Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence, IBR approved for §60.4415(a).

(172) ASTM D5504-01, Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence, IBR approved for §§60.334(h) and 60.4360.

(173) ASTM D5504-08, Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence, (Approved June 15, 2008), IBR approved for §§60.107a(e) and 60.5413(d).

(174) ASTM D5762-02, Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence, IBR approved for §60.335(b).

(175) ASTM D5865-98, Standard Test Method for Gross Calorific Value of Coal and Coke, IBR approved for §§60.45(f) and 60.46(c), and appendix A-7 to part 60: Method 19, Section 12.5.2.1.3.

(176) ASTM D5865-10, Standard Test Method for Gross Calorific Value of Coal and Coke, (Approved January 1, 2010), IBR approved for §§60.45(f), 60.46(c), and appendix A-7 to part 60: Method 19, section 12.5.2.1.3.

(177) ASTM D6216-98, Standard Practice for Opacity Monitor Manufacturers to Certify Conformance with Design and Performance Specifications, IBR approved for appendix B to part 60: Performance Specification 1.

(178) ASTM D6228-98, Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Flame Photometric Detection, IBR approved for §60.334(h).

(179) ASTM D6228-98 (Reapproved 2003), Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Flame Photometric Detection, IBR approved for §§60.4360 and 60.4415.

(180) ASTM D6348-03, Standard Test Method for Determination of Gaseous Compounds by Extractive Direct Interface Fourier Transform Infrared (FTIR) Spectroscopy, (Approved October 1, 2003), IBR approved for §60.73a(b), table 7 to subpart IIII, and table 2 to subpart JJJJ.

(181) ASTM D6366-99, Standard Test Method for Total Trace Nitrogen and Its Derivatives in Liquid Aromatic Hydrocarbons by Oxidative Combustion and Electrochemical Detection, IBR approved for §60.335(b)(9).

(182) ASTM D6420-99 (Reapproved 2004), Standard Test Method for Determination of Gaseous Organic Compounds by Direct Interface Gas Chromatography-Mass Spectrometry, (Approved October 1, 2004), IBR approved for §60.107a(d) and table 2 to subpart JJJJ.

(183) ASTM D6522-00, Standard Test Method for Determination of Nitrogen Oxides, Carbon Monoxide, and Oxygen Concentrations in Emissions from Natural Gas-Fired Reciprocating Engines, Combustion Turbines, Boilers, and Process Heaters Using Portable Analyzers, IBR approved for §60.335(a).

(184) ASTM D6522-00 (Reapproved 2005), Standard Test Method for Determination of Nitrogen Oxides, Carbon Monoxide, and Oxygen Concentrations in Emissions from Natural Gas-Fired Reciprocating Engines, Combustion Turbines, Boilers, and Process Heaters Using Portable Analyzers, (Approved October 1, 2005), IBR approved for table 2 to subpart JJJJ, and §§60.5413(b) and (d).

(185) ASTM D6667-01, Standard Test Method for Determination of Total Volatile Sulfur in Gaseous Hydrocarbons and Liquefied Petroleum Gases by Ultraviolet Fluorescence, IBR approved for §60.335(b).

(186) ASTM D6667-04, Standard Test Method for Determination of Total Volatile Sulfur in Gaseous Hydrocarbons and Liquefied Petroleum Gases by Ultraviolet Fluorescence, IBR approved for §60.4415(a).

(187) ASTM D6751-11b, Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels, including Appendices X1 through X3, (Approved July 15, 2011), IBR approved for §§60.41b and 60.41c.

(188) ASTM D6784-02, Standard Test Method for Elemental, Oxidized, Particle-Bound and Total Mercury in Flue Gas Generated from Coal-Fired Stationary Sources (Ontario Hydro Method), IBR approved for §60.56c(b) and appendix B to part 60: Performance Specification 12A, Section 8.6.2.

(189) ASTM D6784-02 (Reapproved 2008) Standard Test Method for Elemental, Oxidized, Particle-Bound and Total Mercury in Flue Gas Generated from Coal-Fired Stationary Sources (Ontario Hydro Method), (Approved April 1, 2008), IBR approved for §§60.2165(j) and 60.2730(j), tables 1, 5, 6 and 8 to subpart CCCC, and tables 2, 6, 7, and 9 to subpart DDDD, §§60.4900(b), 60.5220(b), tables 1 and 2 to subpart LLLL, and tables 2 and 3 to subpart MMMM.

(190) ASTM D7467-10, Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20), including Appendices X1 through X3, (Approved August 1, 2010), IBR approved for §§60.41b and 60.41c.

(191) ASTM E168-67, General Techniques of Infrared Quantitative Analysis, IBR approved for §§60.485a(d), 60.593(b), 60.593a(b), and 60.632(f).

(192) ASTM E168-77, General Techniques of Infrared Quantitative Analysis, IBR approved for §§60.485a(d), 60.593(b), 60.593a(b), and 60.632(f).

(193) ASTM E168-92, General Techniques of Infrared Quantitative Analysis, IBR approved for §§60.485a(d)(1), 60.593(b)(2), 60.593a(b)(2), 60.632(f), and 60.5400.

(194) ASTM E169-63, General Techniques of Ultraviolet Quantitative Analysis, IBR approved for §§60.485a(d), 60.593(b), 60.593a(b), and 60.632(f) .

(195) ASTM E169-77, General Techniques of Ultraviolet Quantitative Analysis, IBR approved for §§60.485a(d), 60.593(b), and 60.593a(b), 60.632(f).

(196) ASTM E169-93, General Techniques of Ultraviolet Quantitative Analysis, (Approved May 15, 1993), IBR approved for §§60.485a(d), 60.593(b), 60.593a(b), 60.632(f), and 60.5400(f).

(197) ASTM E260-73, General Gas Chromatography Procedures, IBR approved for §§60.485a(d), 60.593(b), 60.593a(b), and 60.632(f).

(198) ASTM E260-91, General Gas Chromatography Procedures, (IBR approved for §§60.485a(d), 60.593(b), 60.593a(b), and 60.632(f).

(199) ASTM E260-96, General Gas Chromatography Procedures, (Approved April 10, 1996), IBR approved for §§60.485a(d), 60.593(b), 60.593a(b), 60.632(f), 60.5400(f), and 60.5406(b).

(200) ASTM E1584-11, Standard Test Method for Assay of Nitric Acid, (Approved August 1, 2011), IBR approved for §60.73a(c).

(201) ASTM UOP539-97, Refinery Gas Analysis by Gas Chromatography, (Copyright 1997), IBR approved for §60.107a(d).

(h) Association of Official Analytical Chemists, 1111 North 19th Street, Suite 210, Arlington, VA 22209.

(1) AOAC Method 9, Official Methods of Analysis of the Association of Official Analytical Chemists (AOAC), 11th edition, 1970, pp. 11-12, IBR approved for §§60.204(b), 60.214(b), 60.224(b), and 60.234(b).

(2) [Reserved]

(i) U.S. Environmental Protection Agency, 1200 Pennsylvania Avenue NW., Washington, DC 20460, (202) 272-0167, http://www.epa.gov.

(1) EPA-454/R-98-015, Office of Air Quality Planning and Standards (OAQPS) Fabric Filter Bag Leak Detection Guidance, September 1997, IBR approved for §§60.2145(r), 60.2710(r), 60.4905(b), and 60.5225(b).

(2) [Reserved]

(j) The Gas Processors Association, 6526 East 60th Street, Tulsa, OK 74145; also available through Information Handling Services, 15 Inverness Way East, PO Box 1154, Englewood, CO 80150-1154. You may inspect a copy at the EPA's Air and Radiation Docket and Information Center, Room 3334, 1301 Constitution Ave. NW., Washington, DC 20460.

(1) Gas Processors Association Standard 2172-09, Calculation of Gross Heating Value, Relative Density, Compressibility and Theoretical Hydrocarbon Liquid Content for Natural Gas Mixtures for Custody Transfer (2009), IBR approved for §60.107a(d).

(2) Gas Processors Association Standard 2261-00, Analysis for Natural Gas and Similar Gaseous Mixtures by Gas Chromatography (2000), IBR approved for §60.107a(d).

(3) Gas Processors Association Standard 2377-86, Test for Hydrogen Sulfide and Carbon Dioxide in Natural Gas Using Length of Stain Tubes, 1986 Revision, IBR approved for §§60.105(b), 60.107a(b), 60.334(h), 60.4360, and 60.4415(a).

(k) International Organization for Standardization (ISO) available through IHS Inc., 15 Inverness Way East, Englewood, CO 80112.

(1) ISO 8178-4: 1996(E), Reciprocating Internal Combustion Engines—Exhaust Emission Measurement—part 4: Test Cycles for Different Engine Applications, IBR approved for §60.4241(b).

(2) [Reserved]

(l) International Organization for Standardization (ISO), 1, ch. de la Voie-Creuse, Case postale 56, CH-1211 Geneva 20, Switzerland, +41 22 749 01 11, http://www.iso.org/iso/home.htm.

(1) ISO 8316: Measurement of Liquid Flow in Closed Conduits—Method by Collection of the Liquid in a Volumetric Tank (1987-10-01)—First Edition, IBR approved for §60.107a(d).

(2) [Reserved]

(m) This material is available for purchase from the National Technical Information Services (NTIS), 5285 Port Royal Road, Springfield, Virginia 22161. You may inspect a copy at the EPA's Air and Radiation Docket and Information Center (Docket A-91-61, Item IV-J-125), Room M-1500, 1200 Pennsylvania Ave. NW., Washington, DC 20460.

(1) OMB Bulletin No. 93-17: Revised Statistical Definitions for Metropolitan Areas. Office of Management and Budget, June 30, 1993. NTIS No. PB 93-192-664. IBR approved for §60.31e.

(2) [Reserved]

(n) North American Electric Reliability Corporation, 1325 G Street NW., Suite 600, Washington, DC 20005-3801, http://www.nerc.com.

(1) North American Electric Reliability Corporation Reliability Standard EOP-002-3, Capacity and Energy Emergencies, updated November 19, 2012, IBR approved for §§60.4211(f) and 60.4243(d). Also available online: http://www.nerc.com/files/EOP-002-3_1.pdf.

(2) [Reserved]

(o) The following material is available for purchase from the Technical Association of the Pulp and Paper Industry (TAPPI), 15 Technology Parkway South, Suite 115, Peachtree Corners, GA 30092, Telephone (800) 332-8686, and is also available at the following Web site: http://www.tappi.org.

(1) TAPPI Method T 624 cm-11, (Copyright 2011), IBR approved, for §§60.285(d) and 60.285a(d).

(2) [Reserved]

(p) Underwriter's Laboratories, Inc. (UL), 333 Pfingsten Road, Northbrook, IL 60062.

(1) UL 103, Sixth Edition revised as of September 3, 1986, Standard for Chimneys, Factory-built, Residential Type and Building Heating Appliance, IBR approved for Appendix A-8 to part 60.

(2) [Reserved]

(q) Water Pollution Control Federation (WPCF), 2626 Pennsylvania Avenue NW., Washington, DC 20037.

(1) Method 209A, Total Residue Dried at 103-105 °C, in Standard Methods for the Examination of Water and Wastewater, 15th Edition, 1980, IBR approved for §60.683(b).

(2) [Reserved]

(r) West Coast Lumber Inspection Bureau, 6980 SW. Barnes Road, Portland, OR 97223.

(1) West Coast Lumber Standard Grading Rules No. 16, pages 5-21, 90 and 91, September 3, 1970, revised 1984, IBR approved for Appendix A-8 to part 60.

(2) [Reserved]

[79 FR 11242, Feb. 27, 2014, as amended at 79 FR 18965, Apr. 4, 2014]

§60.18   General control device and work practice requirements.

(a) Introduction. (1) This section contains requirements for control devices used to comply with applicable subparts of 40 CFR parts 60 and 61. The requirements are placed here for administrative convenience and apply only to facilities covered by subparts referring to this section.

(2) This section also contains requirements for an alternative work practice used to identify leaking equipment. This alternative work practice is placed here for administrative convenience and is available to all subparts in 40 CFR parts 60, 61, 63, and 65 that require monitoring of equipment with a 40 CFR part 60, Appendix A-7, Method 21 monitor.

(b) Flares. Paragraphs (c) through (f) apply to flares.

(c)(1) Flares shall be designed for and operated with no visible emissions as determined by the methods specified in paragraph (f), except for periods not to exceed a total of 5 minutes during any 2 consecutive hours.

(2) Flares shall be operated with a flame present at all times, as determined by the methods specified in paragraph (f).

(3) An owner/operator has the choice of adhering to either the heat content specifications in paragraph (c)(3)(ii) of this section and the maximum tip velocity specifications in paragraph (c)(4) of this section, or adhering to the requirements in paragraph (c)(3)(i) of this section.

(i)(A) Flares shall be used that have a diameter of 3 inches or greater, are nonassisted, have a hydrogen content of 8.0 percent (by volume), or greater, and are designed for and operated with an exit velocity less than 37.2 m/sec (122 ft/sec) and less than the velocity, Vmax, as determined by the following equation:

Vmax = (XH2−K1)* K2

Where:

Vmax = Maximum permitted velocity, m/sec.

K1 = Constant, 6.0 volume-percent hydrogen.

K2 = Constant, 3.9(m/sec)/volume-percent hydrogen.

XH2 = The volume-percent of hydrogen, on a wet basis, as calculated by using the American Society for Testing and Materials (ASTM) Method D1946-77. (Incorporated by reference as specified in §60.17).

(B) The actual exit velocity of a flare shall be determined by the method specified in paragraph (f)(4) of this section.

(ii) Flares shall be used only with the net heating value of the gas being combusted being 11.2 MJ/scm (300 Btu/scf) or greater if the flare is steam-assisted or air-assisted; or with the net heating value of the gas being combusted being 7.45 MJ/scm (200 Btu/scf) or greater if the flare is nonassisted. The net heating value of the gas being combusted shall be determined by the methods specified in paragraph (f)(3) of this section.

(4)(i) Steam-assisted and nonassisted flares shall be designed for and operated with an exit velocity, as determined by the methods specified in paragraph (f)(4) of this section, less than 18.3 m/sec (60 ft/sec), except as provided in paragraphs (c)(4) (ii) and (iii) of this section.

(ii) Steam-assisted and nonassisted flares designed for and operated with an exit velocity, as determined by the methods specified in paragraph (f)(4), equal to or greater than 18.3 m/sec (60 ft/sec) but less than 122 m/sec (400 ft/sec) are allowed if the net heating value of the gas being combusted is greater than 37.3 MJ/scm (1,000 Btu/scf).

(iii) Steam-assisted and nonassisted flares designed for and operated with an exit velocity, as determined by the methods specified in paragraph (f)(4), less than the velocity, Vmax, as determined by the method specified in paragraph (f)(5), and less than 122 m/sec (400 ft/sec) are allowed.

(5) Air-assisted flares shall be designed and operated with an exit velocity less than the velocity, Vmax, as determined by the method specified in paragraph (f)(6).

(6) Flares used to comply with this section shall be steam-assisted, air-assisted, or nonassisted.

(d) Owners or operators of flares used to comply with the provisions of this subpart shall monitor these control devices to ensure that they are operated and maintained in conformance with their designs. Applicable subparts will provide provisions stating how owners or operators of flares shall monitor these control devices.

(e) Flares used to comply with provisions of this subpart shall be operated at all times when emissions may be vented to them.

(f)(1) Method 22 of appendix A to this part shall be used to determine the compliance of flares with the visible emission provisions of this subpart. The observation period is 2 hours and shall be used according to Method 22.

(2) The presence of a flare pilot flame shall be monitored using a thermocouple or any other equivalent device to detect the presence of a flame.

(3) The net heating value of the gas being combusted in a flare shall be calculated using the following equation:

eCFR graphic ec01jn92.008.gif

View or download PDF

where:

HT = Net heating value of the sample, MJ/scm; where the net enthalpy per mole of offgas is based on combustion at 25 °C and 760 mm Hg, but the standard temperature for determining the volume corresponding to one mole is 20 °C;

eCFR graphic ec01jn92.009.gif

View or download PDF

Ci = Concentration of sample component i in ppm on a wet basis, as measured for organics by Reference Method 18 and measured for hydrogen and carbon monoxide by ASTM D1946-77 or 90 (Reapproved 1994) (Incorporated by reference as specified in §60.17); and

Hi = Net heat of combustion of sample component i, kcal/g mole at 25 °C and 760 mm Hg. The heats of combustion may be determined using ASTM D2382-76 or 88 or D4809-95 (incorporated by reference as specified in §60.17) if published values are not available or cannot be calculated.

(4) The actual exit velocity of a flare shall be determined by dividing the volumetric flowrate (in units of standard temperature and pressure), as determined by Reference Methods 2, 2A, 2C, or 2D as appropriate; by the unobstructed (free) cross sectional area of the flare tip.

(5) The maximum permitted velocity, Vmax, for flares complying with paragraph (c)(4)(iii) shall be determined by the following equation.

Log10 (Vmax)=(HT+28.8)/31.7

Vmax = Maximum permitted velocity, M/sec

28.8=Constant

31.7=Constant

HT = The net heating value as determined in paragraph (f)(3).

(6) The maximum permitted velocity, Vmax, for air-assisted flares shall be determined by the following equation.

Vmax = 8.706+0.7084 (HT)

Vmax = Maximum permitted velocity, m/sec

8.706=Constant

0.7084=Constant

HT = The net heating value as determined in paragraph (f)(3).

(g) Alternative work practice for monitoring equipment for leaks. Paragraphs (g), (h), and (i) of this section apply to all equipment for which the applicable subpart requires monitoring with a 40 CFR part 60, Appendix A-7, Method 21 monitor, except for closed vent systems, equipment designated as leakless, and equipment identified in the applicable subpart as having no detectable emissions, as indicated by an instrument reading of less than 500 ppm above background. An owner or operator may use an optical gas imaging instrument instead of a 40 CFR part 60, Appendix A-7, Method 21 monitor. Requirements in the existing subparts that are specific to the Method 21 instrument do not apply under this section. All other requirements in the applicable subpart that are not addressed in paragraphs (g), (h), and (i) of this section apply to this standard. For example, equipment specification requirements, and non-Method 21 instrument recordkeeping and reporting requirements in the applicable subpart continue to apply. The terms defined in paragraphs (g)(1) through (5) of this section have meanings that are specific to the alternative work practice standard in paragraphs (g), (h), and (i) of this section.

(1) Applicable subpart means the subpart in 40 CFR parts 60, 61, 63, or 65 that requires monitoring of equipment with a 40 CFR part 60, Appendix A-7, Method 21 monitor.

(2) Equipment means pumps, valves, pressure relief valves, compressors, open-ended lines, flanges, connectors, and other equipment covered by the applicable subpart that require monitoring with a 40 CFR part 60, Appendix A-7, Method 21 monitor.

(3) Imaging means making visible emissions that may otherwise be invisible to the naked eye.

(4) Optical gas imaging instrument means an instrument that makes visible emissions that may otherwise be invisible to the naked eye.

(5) Repair means that equipment is adjusted, or otherwise altered, in order to eliminate a leak.

(6) Leak means:

(i) Any emissions imaged by the optical gas instrument;

(ii) Indications of liquids dripping;

(iii) Indications by a sensor that a seal or barrier fluid system has failed; or

(iv) Screening results using a 40 CFR part 60, Appendix A-7, Method 21 monitor that exceed the leak definition in the applicable subpart to which the equipment is subject.

(h) The alternative work practice standard for monitoring equipment for leaks is available to all subparts in 40 CFR parts 60, 61, 63, and 65 that require monitoring of equipment with a 40 CFR part 60, Appendix A-7, Method 21 monitor.

(1) An owner or operator of an affected source subject to CFR parts 60, 61, 63, or 65 can choose to comply with the alternative work practice requirements in paragraph (i) of this section instead of using the 40 CFR part 60, Appendix A-7, Method 21 monitor to identify leaking equipment. The owner or operator must document the equipment, process units, and facilities for which the alternative work practice will be used to identify leaks.

(2) Any leak detected when following the leak survey procedure in paragraph (i)(3) of this section must be identified for repair as required in the applicable subpart.

(3) If the alternative work practice is used to identify leaks, re-screening after an attempted repair of leaking equipment must be conducted using either the alternative work practice or the 40 CFR part 60, Appendix A-7, Method 21 monitor at the leak definition required in the applicable subpart to which the equipment is subject.

(4) The schedule for repair is as required in the applicable subpart.

(5) When this alternative work practice is used for detecting leaking equipment, choose one of the monitoring frequencies listed in Table 1 to subpart A of this part in lieu of the monitoring frequency specified for regulated equipment in the applicable subpart. Reduced monitoring frequencies for good performance are not applicable when using the alternative work practice.

(6) When this alternative work practice is used for detecting leaking equipment the following are not applicable for the equipment being monitored:

(i) Skip period leak detection and repair;

(ii) Quality improvement plans; or

(iii) Complying with standards for allowable percentage of valves and pumps to leak.

(7) When the alternative work practice is used to detect leaking equipment, the regulated equipment in paragraph (h)(1)(i) of this section must also be monitored annually using a 40 CFR part 60, Appendix A-7, Method 21 monitor at the leak definition required in the applicable subpart. The owner or operator may choose the specific monitoring period (for example, first quarter) to conduct the annual monitoring. Subsequent monitoring must be conducted every 12 months from the initial period. Owners or operators must keep records of the annual Method 21 screening results, as specified in paragraph (i)(4)(vii) of this section.

(i) An owner or operator of an affected source who chooses to use the alternative work practice must comply with the requirements of paragraphs (i)(1) through (i)(5) of this section.

(1) Instrument Specifications. The optical gas imaging instrument must comply with the requirements in (i)(1)(i) and (i)(1)(ii) of this section.

(i) Provide the operator with an image of the potential leak points for each piece of equipment at both the detection sensitivity level and within the distance used in the daily instrument check described in paragraph (i)(2) of this section. The detection sensitivity level depends upon the frequency at which leak monitoring is to be performed.

(ii) Provide a date and time stamp for video records of every monitoring event.

(2) Daily Instrument Check. On a daily basis, and prior to beginning any leak monitoring work, test the optical gas imaging instrument at the mass flow rate determined in paragraph (i)(2)(i) of this section in accordance with the procedure specified in paragraphs (i)(2)(ii) through (i)(2)(iv) of this section for each camera configuration used during monitoring (for example, different lenses used), unless an alternative method to demonstrate daily instrument checks has been approved in accordance with paragraph (i)(2)(v) of this section.

(i) Calculate the mass flow rate to be used in the daily instrument check by following the procedures in paragraphs (i)(2)(i)(A) and (i)(2)(i)(B) of this section.

(A) For a specified population of equipment to be imaged by the instrument, determine the piece of equipment in contact with the lowest mass fraction of chemicals that are detectable, within the distance to be used in paragraph (i)(2)(iv)(B) of this section, at or below the standard detection sensitivity level.

(B) Multiply the standard detection sensitivity level, corresponding to the selected monitoring frequency in Table 1 of subpart A of this part, by the mass fraction of detectable chemicals from the stream identified in paragraph (i)(2)(i)(A) of this section to determine the mass flow rate to be used in the daily instrument check, using the following equation.

eCFR graphic er22de08.007.gif

View or download PDF

Where:

Edic = Mass flow rate for the daily instrument check, grams per hour

xi = Mass fraction of detectable chemical(s) i seen by the optical gas imaging instrument, within the distance to be used in paragraph (i)(2)(iv)(B) of this section, at or below the standard detection sensitivity level, Esds.

Esds = Standard detection sensitivity level from Table 1 to subpart A, grams per hour

k = Total number of detectable chemicals emitted from the leaking equipment and seen by the optical gas imaging instrument.

(ii) Start the optical gas imaging instrument according to the manufacturer's instructions, ensuring that all appropriate settings conform to the manufacturer's instructions.

(iii) Use any gas chosen by the user that can be viewed by the optical gas imaging instrument and that has a purity of no less than 98 percent.

(iv) Establish a mass flow rate by using the following procedures:

(A) Provide a source of gas where it will be in the field of view of the optical gas imaging instrument.

(B) Set up the optical gas imaging instrument at a recorded distance from the outlet or leak orifice of the flow meter that will not be exceeded in the actual performance of the leak survey. Do not exceed the operating parameters of the flow meter.

(C) Open the valve on the flow meter to set a flow rate that will create a mass emission rate equal to the mass rate specified in paragraph (i)(2)(i) of this section while observing the gas flow through the optical gas imaging instrument viewfinder. When an image of the gas emission is seen through the viewfinder at the required emission rate, make a record of the reading on the flow meter.

(v) Repeat the procedures specified in paragraphs (i)(2)(ii) through (i)(2)(iv) of this section for each configuration of the optical gas imaging instrument used during the leak survey.

(vi) To use an alternative method to demonstrate daily instrument checks, apply to the Administrator for approval of the alternative under §60.13(i).

(3) Leak Survey Procedure. Operate the optical gas imaging instrument to image every regulated piece of equipment selected for this work practice in accordance with the instrument manufacturer's operating parameters. All emissions imaged by the optical gas imaging instrument are considered to be leaks and are subject to repair. All emissions visible to the naked eye are also considered to be leaks and are subject to repair.

(4) Recordkeeping. You must keep the records described in paragraphs (i)(4)(i) through (i)(4)(vii) of this section:

(i) The equipment, processes, and facilities for which the owner or operator chooses to use the alternative work practice.

(ii) The detection sensitivity level selected from Table 1 to subpart A of this part for the optical gas imaging instrument.

(iii) The analysis to determine the piece of equipment in contact with the lowest mass fraction of chemicals that are detectable, as specified in paragraph (i)(2)(i)(A) of this section.

(iv) The technical basis for the mass fraction of detectable chemicals used in the equation in paragraph (i)(2)(i)(B) of this section.

(v) The daily instrument check. Record the distance, per paragraph (i)(2)(iv)(B) of this section, and the flow meter reading, per paragraph (i)(2)(iv)(C) of this section, at which the leak was imaged. Keep a video record of the daily instrument check for each configuration of the optical gas imaging instrument used during the leak survey (for example, the daily instrument check must be conducted for each lens used). The video record must include a time and date stamp for each daily instrument check. The video record must be kept for 5 years.

(vi) Recordkeeping requirements in the applicable subpart. A video record must be used to document the leak survey results. The video record must include a time and date stamp for each monitoring event. A video record can be used to meet the recordkeeping requirements of the applicable subparts if each piece of regulated equipment selected for this work practice can be identified in the video record. The video record must be kept for 5 years.

(vii) The results of the annual Method 21 screening required in paragraph (h)(7) of this section. Records must be kept for all regulated equipment specified in paragraph (h)(1) of this section. Records must identify the equipment screened, the screening value measured by Method 21, the time and date of the screening, and calibration information required in the existing applicable subpart.

(5) Reporting. Submit the reports required in the applicable subpart. Submit the records of the annual Method 21 screening required in paragraph (h)(7) of this section to the Administrator via e-mail to CCG-AWP@EPA.GOV.

[51 FR 2701, Jan. 21, 1986, as amended at 63 FR 24444, May 4, 1998; 65 FR 61752, Oct. 17, 2000; 73 FR 78209, Dec. 22, 2008]

§60.19   General notification and reporting requirements.

(a) For the purposes of this part, time periods specified in days shall be measured in calendar days, even if the word “calendar” is absent, unless otherwise specified in an applicable requirement.

(b) For the purposes of this part, if an explicit postmark deadline is not specified in an applicable requirement for the submittal of a notification, application, report, or other written communication to the Administrator, the owner or operator shall postmark the submittal on or before the number of days specified in the applicable requirement. For example, if a notification must be submitted 15 days before a particular event is scheduled to take place, the notification shall be postmarked on or before 15 days preceding the event; likewise, if a notification must be submitted 15 days after a particular event takes place, the notification shall be delivered or postmarked on or before 15 days following the end of the event. The use of reliable non-Government mail carriers that provide indications of verifiable delivery of information required to be submitted to the Administrator, similar to the postmark provided by the U.S. Postal Service, or alternative means of delivery, including the use of electronic media, agreed to by the permitting authority, is acceptable.

(c) Notwithstanding time periods or postmark deadlines specified in this part for the submittal of information to the Administrator by an owner or operator, or the review of such information by the Administrator, such time periods or deadlines may be changed by mutual agreement between the owner or operator and the Administrator. Procedures governing the implementation of this provision are specified in paragraph (f) of this section.

(d) If an owner or operator of an affected facility in a State with delegated authority is required to submit periodic reports under this part to the State, and if the State has an established timeline for the submission of periodic reports that is consistent with the reporting frequency(ies) specified for such facility under this part, the owner or operator may change the dates by which periodic reports under this part shall be submitted (without changing the frequency of reporting) to be consistent with the State's schedule by mutual agreement between the owner or operator and the State. The allowance in the previous sentence applies in each State beginning 1 year after the affected facility is required to be in compliance with the applicable subpart in this part. Procedures governing the implementation of this provision are specified in paragraph (f) of this section.

(e) If an owner or operator supervises one or more stationary sources affected by standards set under this part and standards set under part 61, part 63, or both such parts of this chapter, he/she may arrange by mutual agreement between the owner or operator and the Administrator (or the State with an approved permit program) a common schedule on which periodic reports required by each applicable standard shall be submitted throughout the year. The allowance in the previous sentence applies in each State beginning 1 year after the stationary source is required to be in compliance with the applicable subpart in this part, or 1 year after the stationary source is required to be in compliance with the applicable 40 CFR part 61 or part 63 of this chapter standard, whichever is latest. Procedures governing the implementation of this provision are specified in paragraph (f) of this section.

(f)(1)(i) Until an adjustment of a time period or postmark deadline has been approved by the Administrator under paragraphs (f)(2) and (f)(3) of this section, the owner or operator of an affected facility remains strictly subject to the requirements of this part.

(ii) An owner or operator shall request the adjustment provided for in paragraphs (f)(2) and (f)(3) of this section each time he or she wishes to change an applicable time period or postmark deadline specified in this part.

(2) Notwithstanding time periods or postmark deadlines specified in this part for the submittal of information to the Administrator by an owner or operator, or the review of such information by the Administrator, such time periods or deadlines may be changed by mutual agreement between the owner or operator and the Administrator. An owner or operator who wishes to request a change in a time period or postmark deadline for a particular requirement shall request the adjustment in writing as soon as practicable before the subject activity is required to take place. The owner or operator shall include in the request whatever information he or she considers useful to convince the Administrator that an adjustment is warranted.

(3) If, in the Administrator's judgment, an owner or operator's request for an adjustment to a particular time period or postmark deadline is warranted, the Administrator will approve the adjustment. The Administrator will notify the owner or operator in writing of approval or disapproval of the request for an adjustment within 15 calendar days of receiving sufficient information to evaluate the request.

(4) If the Administrator is unable to meet a specified deadline, he or she will notify the owner or operator of any significant delay and inform the owner or operator of the amended schedule.

[59 FR 12428, Mar. 16, 1994, as amended at 64 FR 7463, Feb. 12, 1998]

Table 1 to Subpart A of Part 60-Detection Sensitivity Levels (grams per hour)

Monitoring frequency per subparta Detection sensitivity level
Bi-Monthly60
Semi-Quarterly85
Monthly100

aWhen this alternative work practice is used to identify leaking equipment, the owner or operator must choose one of the monitoring frequencies listed in this table in lieu of the monitoring frequency specified in the applicable subpart. Bi-monthly means every other month. Semi-quarterly means twice per quarter. Monthly means once per month.

[73 FR 78211, Dec. 22, 2008]

Subpart B—Adoption and Submittal of State Plans for Designated Facilities

Source: 40 FR 53346, Nov. 17, 1975, unless otherwise noted.

§60.20   Applicability.

The provisions of this subpart apply to States upon publication of a final guideline document under §60.22(a).

§60.21   Definitions.

Terms used but not defined in this subpart shall have the meaning given them in the Act and in subpart A:

(a) Designated pollutant means any air pollutant, the emissions of which are subject to a standard of performance for new stationary sources, but for which air quality criteria have not been issued and that is not included on a list published under section 108(a) or section 112(b)(1)(A) of the Act.

(b) Designated facility means any existing facility (see §60.2(aa)) which emits a designated pollutant and which would be subject to a standard of performance for that pollutant if the existing facility were an affected facility (see §60.2(e)).

(c) Plan means a plan under section 111(d) of the Act which establishes emission standards for designated pollutants from designated facilities and provides for the implementation and enforcement of such emission standards.

(d) Applicable plan means the plan, or most recent revision thereof, which has been approved under §60.27(b) or promulgated under §60.27(d).

(e) Emission guideline means a guideline set forth in subpart C of this part, or in a final guideline document published under §60.22(a), which reflects the degree of emission reduction achievable through the application of the best system of emission reduction which (taking into account the cost of such reduction) the Administrator has determined has been adequately demonstrated for designated facilities.

(f) Emission standard means a legally enforceable regulation setting forth an allowable rate of emissions into the atmosphere, establishing an allowance system, or prescribing equipment specifications for control of air pollution emissions.

(g) Compliance schedule means a legally enforceable schedule specifying a date or dates by which a source or category of sources must comply with specific emission standards contained in a plan or with any increments of progress to achieve such compliance.

(h) Increments of progress means steps to achieve compliance which must be taken by an owner or operator of a designated facility, including:

(1) Submittal of a final control plan for the designated facility to the appropriate air pollution control agency;

(2) Awarding of contracts for emission control systems or for process modifications, or issuance of orders for the purchase of component parts to accomplish emission control or process modification;

(3) Initiation of on-site construction or installation of emission control equipment or process change;

(4) Completion of on-site construction or installation of emission control equipment or process change; and

(5) Final compliance.

(i) Region means an air quality control region designated under section 107 of the Act and described in part 81 of this chapter.

(j) Local agency means any local governmental agency.

[40 FR 53346, Nov. 17, 1975, as amended at 70 FR 28649, May 18, 2005; 77 FR 9447, Feb. 16, 2012]

§60.22   Publication of guideline documents, emission guidelines, and final compliance times.

(a) Concurrently upon or after proposal of standards of performance for the control of a designated pollutant from affected facilities, the Administrator will publish a draft guideline document containing information pertinent to control of the designated pollutant form designated facilities. Notice of the availability of the draft guideline document will be published in the Federal Register and public comments on its contents will be invited. After consideration of public comments and upon or after promulgation of standards of performance for control of a designated pollutant from affected facilities, a final guideline document will be published and notice of its availability will be published in the Federal Register.

(b) Guideline documents published under this section will provide information for the development of State plans, such as:

(1) Information concerning known or suspected endangerment of public health or welfare caused, or contributed to, by the designated pollutant.

(2) A description of systems of emission reduction which, in the judgment of the Administrator, have been adequately demonstrated.

(3) Information on the degree of emission reduction which is achievable with each system, together with information on the costs and environmental effects of applying each system to designated facilities.

(4) Incremental periods of time normally expected to be necessary for the design, installation, and startup of identified control systems.

(5) An emission guideline that reflects the application of the best system of emission reduction (considering the cost of such reduction) that has been adequately demonstrated for designated facilities, and the time within which compliance with emission standards of equivalent stringency can be achieved. The Administrator will specify different emission guidelines or compliance times or both for different sizes, types, and classes of designated facilities when costs of control, physical limitations, geographical location, or similar factors make subcategorization appropriate. (6) Such other available information as the Administrator determines may contribute to the formulation of State plans.

(c) Except as provided in paragraph (d)(1) of this section, the emission guidelines and compliance times referred to in paragraph (b)(5) of this section will be proposed for comment upon publication of the draft guideline document, and after consideration of comments will be promulgated in subpart C of this part with such modifications as may be appropriate.

(d)(1) If the Administrator determines that a designated pollutant may cause or contribute to endangerment of public welfare, but that adverse effects on public health have not been demonstrated, he will include the determination in the draft guideline document and in the Federal Register notice of its availability. Except as provided in paragraph (d)(2) of this section, paragraph (c) of this section shall be inapplicable in such cases.

(2) If the Administrator determines at any time on the basis of new information that a prior determination under paragraph (d)(1) of this section is incorrect or no longer correct, he will publish notice of the determination in the Federal Register, revise the guideline document as necessary under paragraph (a) of this section, and propose and promulgate emission guidelines and compliance times under paragraph (c) of this section.

[40 FR 53346, Nov. 17, 1975, as amended at 54 FR 52189, Dec. 20, 1989]

§60.23   Adoption and submittal of State plans; public hearings.

(a)(1) Unless otherwise specified in the applicable subpart, within 9 months after notice of the availability of a final guideline document is published under §60.22(a), each State shall adopt and submit to the Administrator, in accordance with §60.4 of subpart A of this part, a plan for the control of the designated pollutant to which the guideline document applies.

(2) Within nine months after notice of the availability of a final revised guideline document is published as provided in §60.22(d)(2), each State shall adopt and submit to the Administrator any plan revision necessary to meet the requirements of this subpart.

(b) If no designated facility is located within a State, the State shall submit a letter of certification to that effect to the Administrator within the time specified in paragraph (a) of this section. Such certification shall exempt the State from the requirements of this subpart for that designated pollutant.

(c)(1) Except as provided in paragraphs (c)(2) and (c)(3) of this section, the State shall, prior to the adoption of any plan or revision thereof, conduct one or more public hearings within the State on such plan or plan revision.

(2) No hearing shall be required for any change to an increment of progress in an approved compliance schedule unless the change is likely to cause the facility to be unable to comply with the final compliance date in the schedule.

(3) No hearing shall be required on an emission standard in effect prior to the effective date of this subpart if it was adopted after a public hearing and is at least as stringent as the corresponding emission guideline specified in the applicable guideline document published under §60.22(a).

(d) Any hearing required by paragraph (c) of this section shall be held only after reasonable notice. Notice shall be given at least 30 days prior to the date of such hearing and shall include:

(1) Notification to the public by prominently advertising the date, time, and place of such hearing in each region affected;

(2) Availability, at the time of public announcement, of each proposed plan or revision thereof for public inspection in at least one location in each region to which it will apply;

(3) Notification to the Administrator;

(4) Notification to each local air pollution control agency in each region to which the plan or revision will apply; and

(5) In the case of an interstate region, notification to any other State included in the region.

(e) The State shall prepare and retain, for a minimum of 2 years, a record of each hearing for inspection by any interested party. The record shall contain, as a minimum, a list of witnesses together with the text of each presentation.

(f) The State shall submit with the plan or revision:

(1) Certification that each hearing required by paragraph (c) of this section was held in accordance with the notice required by paragraph (d) of this section; and

(2) A list of witnesses and their organizational affiliations, if any, appearing at the hearing and a brief written summary of each presentation or written submission.

(g) Upon written application by a State agency (through the appropriate Regional Office), the Administrator may approve State procedures designed to insure public participation in the matters for which hearings are required and public notification of the opportunity to participate if, in the judgment of the Administrator, the procedures, although different from the requirements of this subpart, in fact provide for adequate notice to and participation of the public. The Administrator may impose such conditions on his approval as he deems necessary. Procedures approved under this section shall be deemed to satisfy the requirements of this subpart regarding procedures for public hearings.

[40 FR 53346, Nov. 17, 1975, as amended at 60 FR 65414, Dec. 19, 1995]

§60.24   Emission standards and compliance schedules.

(a) Each plan shall include emission standards and compliance schedules.

(b) (1) Emission standards shall either be based on an allowance system or prescribe allowable rates of emissions except when it is clearly impracticable. Such cases will be identified in the guideline documents issued under §60.22. Where emission standards prescribing equipment specifications are established, the plan shall, to the degree possible, set forth the emission reductions achievable by implementation of such specifications, and may permit compliance by the use of equipment determined by the State to be equivalent to that prescribed.

(2) Test methods and procedures for determining compliance with the emission standards shall be specified in the plan. Methods other than those specified in appendix A to this part may be specified in the plan if shown to be equivalent or alternative methods as defined in §60.2 (t) and (u).

(3) Emission standards shall apply to all designated facilities within the State. A plan may contain emission standards adopted by local jurisdictions provided that the standards are enforceable by the State.

(c) Except as provided in paragraph (f) of this section, where the Administrator has determined that a designated pollutant may cause or contribute to endangerment of public health, emission standards shall be no less stringent than the corresponding emission guideline(s) specified in subpart C of this part, and final compliance shall be required as expeditiously as practicable but no later than the compliance times specified in subpart C of this part.

(d) Where the Administrator has determined that a designated pollutant may cause or contribute to endangerment of public welfare but that adverse effects on public health have not been demonstrated, States may balance the emission guidelines, compliance times, and other information provided in the applicable guideline document against other factors of public concern in establishing emission standards, compliance schedules, and variances. Appropriate consideration shall be given to the factors specified in §60.22(b) and to information presented at the public hearing(s) conducted under §60.23(c).

(e)(1) Any compliance schedule extending more than 12 months from the date required for submittal of the plan must include legally enforceable increments of progress to achieve compliance for each designated facility or category of facilities. Unless otherwise specified in the applicable subpart, increments of progress must include, where practicable, each increment of progress specified in §60.21(h) and must include such additional increments of progress as may be necessary to permit close and effective supervision of progress toward final compliance.

(2) A plan may provide that compliance schedules for individual sources or categories of sources will be formulated after plan submittal. Any such schedule shall be the subject of a public hearing held according to §60.23 and shall be submitted to the Administrator within 60 days after the date of adoption of the schedule but in no case later than the date prescribed for submittal of the first semiannual report required by §60.25(e).

(f) Unless otherwise specified in the applicable subpart on a case-by-case basis for particular designated facilities or classes of facilities, States may provide for the application of less stringent emissions standards or longer compliance schedules than those otherwise required by paragraph (c) of this section, provided that the State demonstrates with respect to each such facility (or class of facilities):

(1) Unreasonable cost of control resulting from plant age, location, or basic process design;

(2) Physical impossibility of installing necessary control equipment; or

(3) Other factors specific to the facility (or class of facilities) that make application of a less stringent standard or final compliance time significantly more reasonable.

(g) Nothing in this subpart shall be construed to preclude any State or political subdivision thereof from adopting or enforcing (1) emission standards more stringent than emission guidelines specified in subpart C of this part or in applicable guideline documents or (2) compliance schedules requiring final compliance at earlier times than those specified in subpart C or in applicable guideline documents.

[40 FR 53346, Nov. 17, 1975, as amended at 60 FR 65414, Dec. 19, 1995; 65 FR 76384, Dec. 6, 2000; 70 FR 28649, May 18, 2005; 71 FR 33398, June 9, 2006; 72 FR 59204, Oct. 19, 2007; 77 FR 9447, Feb. 16, 2012]

§60.25   Emission inventories, source surveillance, reports.

(a) Each plan shall include an inventory of all designated facilities, including emission data for the designated pollutants and information related to emissions as specified in appendix D to this part. Such data shall be summarized in the plan, and emission rates of designated pollutants from designated facilities shall be correlated with applicable emission standards. As used in this subpart, “correlated” means presented in such a manner as to show the relationship between measured or estimated amounts of emissions and the amounts of such emissions allowable under applicable emission standards.

(b) Each plan shall provide for monitoring the status of compliance with applicable emission standards. Each plan shall, as a minimum, provide for:

(1) Legally enforceable procedures for requiring owners or operators of designated facilities to maintain records and periodically report to the State information on the nature and amount of emissions from such facilities, and/or such other information as may be necessary to enable the State to determine whether such facilities are in compliance with applicable portions of the plan. Submission of electronic documents shall comply with the requirements of 40 CFR part 3—(Electronic reporting).

(2) Periodic inspection and, when applicable, testing of designated facilities.

(c) Each plan shall provide that information obtained by the State under paragraph (b) of this section shall be correlated with applicable emission standards (see §60.25(a)) and made available to the general public.

(d) The provisions referred to in paragraphs (b) and (c) of this section shall be specifically identified. Copies of such provisions shall be submitted with the plan unless:

(1) They have been approved as portions of a preceding plan submitted under this subpart or as portions of an implementation plan submitted under section 110 of the Act, and

(2) The State demonstrates:

(i) That the provisions are applicable to the designated pollutant(s) for which the plan is submitted, and

(ii) That the requirements of §60.26 are met.

(e) The State shall submit reports on progress in plan enforcement to the Administrator on an annual (calendar year) basis, commencing with the first full report period after approval of a plan or after promulgation of a plan by the Administrator. Information required under this paragraph must be included in the annual report required by §51.321 of this chapter.

(f) Each progress report shall include:

(1) Enforcement actions initiated against designated facilities during the reporting period, under any emission standard or compliance schedule of the plan.

(2) Identification of the achievement of any increment of progress required by the applicable plan during the reporting period.

(3) Identification of designated facilities that have ceased operation during the reporting period.

(4) Submission of emission inventory data as described in paragraph (a) of this section for designated facilities that were not in operation at the time of plan development but began operation during the reporting period.

(5) Submission of additional data as necessary to update the information submitted under paragraph (a) of this section or in previous progress reports.

(6) Submission of copies of technical reports on all performance testing on designated facilities conducted under paragraph (b)(2) of this section, complete with concurrently recorded process data.

[40 FR 53346, Nov. 17, 1975, as amended at 44 FR 65071, Nov. 9, 1979; 70 FR 59887, Oct. 13, 2005]

§60.26   Legal authority.

(a) Each plan shall show that the State has legal authority to carry out the plan, including authority to:

(1) Adopt emission standards and compliance schedules applicable to designated facilities.

(2) Enforce applicable laws, regulations, standards, and compliance schedules, and seek injunctive relief.

(3) Obtain information necessary to determine whether designated facilities are in compliance with applicable laws, regulations, standards, and compliance schedules, including authority to require recordkeeping and to make inspections and conduct tests of designated facilities.

(4) Require owners or operators of designated facilities to install, maintain, and use emission monitoring devices and to make periodic reports to the State on the nature and amounts of emissions from such facilities; also authority for the State to make such data available to the public as reported and as correlated with applicable emission standards.

(b) The provisions of law or regulations which the State determines provide the authorities required by this section shall be specifically identified. Copies of such laws or regulations shall be submitted with the plan unless:

(1) They have been approved as portions of a preceding plan submitted under this subpart or as portions of an implementation plan submitted under section 110 of the Act, and

(2) The State demonstrates that the laws or regulations are applicable to the designated pollutant(s) for which the plan is submitted.

(c) The plan shall show that the legal authorities specified in this section are available to the State at the time of submission of the plan. Legal authority adequate to meet the requirements of paragraphs (a)(3) and (4) of this section may be delegated to the State under section 114 of the Act.

(d) A State governmental agency other than the State air pollution control agency may be assigned responsibility for carrying out a portion of a plan if the plan demonstrates to the Administrator's satisfaction that the State governmental agency has the legal authority necessary to carry out that portion of the plan.

(e) The State may authorize a local agency to carry out a plan, or portion thereof, within the local agency's jurisdiction if the plan demonstrates to the Administrator's satisfaction that the local agency has the legal authority necessary to implement the plan or portion thereof, and that the authorization does not relieve the State of responsibility under the Act for carrying out the plan or portion thereof.

§60.27   Actions by the Administrator.

(a) The Administrator may, whenever he determines necessary, extend the period for submission of any plan or plan revision or portion thereof.

(b) After receipt of a plan or plan revision, the Administrator will propose the plan or revision for approval or disapproval. The Administrator will, within four months after the date required for submission of a plan or plan revision, approve or disapprove such plan or revision or each portion thereof.

(c) The Administrator will, after consideration of any State hearing record, promptly prepare and publish proposed regulations setting forth a plan, or portion thereof, for a State if:

(1) The State fails to submit a plan within the time prescribed;

(2) The State fails to submit a plan revision required by §60.23(a)(2) within the time prescribed; or

(3) The Administrator disapproves the State plan or plan revision or any portion thereof, as unsatisfactory because the requirements of this subpart have not been met.

(d) The Administrator will, within six months after the date required for submission of a plan or plan revision, promulgate the regulations proposed under paragraph (c) of this section with such modifications as may be appropriate unless, prior to such promulgation, the State has adopted and submitted a plan or plan revision which the Administrator determines to be approvable.

(e)(1) Except as provided in paragraph (e)(2) of this section, regulations proposed and promulgated by the Administrator under this section will prescribe emission standards of the same stringency as the corresponding emission guideline(s) specified in the final guideline document published under §60.22(a) and will require final compliance with such standards as expeditiously as practicable but no later than the times specified in the guideline document.

(2) Upon application by the owner or operator of a designated facility to which regulations proposed and promulgated under this section will apply, the Administrator may provide for the application of less stringent emission standards or longer compliance schedules than those otherwise required by this section in accordance with the criteria specified in §60.24(f).

(f) Prior to promulgation of a plan under paragraph (d) of this section, the Administrator will provide the opportunity for at least one public hearing in either:

(1) Each State that failed to hold a public hearing as required by §60.23(c); or

(2) Washington, DC or an alternate location specified in the Federal Register.

[40 FR 53346, Nov. 17, 1975, as amended at 65 FR 76384, Dec. 6, 2000]

§60.28   Plan revisions by the State.

(a) Plan revisions which have the effect of delaying compliance with applicable emission standards or increments of progress or of establishing less stringent emission standards shall be submitted to the Administrator within 60 days after adoption in accordance with the procedures and requirements applicable to development and submission of the original plan.

(b) More stringent emission standards, or orders which have the effect of accelerating compliance, may be submitted to the Administrator as plan revisions in accordance with the procedures and requirements applicable to development and submission of the original plan.

(c) A revision of a plan, or any portion thereof, shall not be considered part of an applicable plan until approved by the Administrator in accordance with this subpart.

§60.29   Plan revisions by the Administrator.

After notice and opportunity for public hearing in each affected State, the Administrator may revise any provision of an applicable plan if:

(a) The provision was promulgated by the Administrator, and

(b) The plan, as revised, will be consistent with the Act and with the requirements of this subpart.

Subpart C—Emission Guidelines and Compliance Times

§60.30   Scope.

The following subparts contain emission guidelines and compliance times for the control of certain designated pollutants in accordance with section 111(d) and section 129 of the Clean Air Act and subpart B of this part.

(a) Subpart Ca [Reserved]

(b) Subpart Cb—Municipal Waste Combustors.

(c) Subpart Cc—Municipal Solid Waste Landfills.

(d) Subpart Cd—Sulfuric Acid Production Plants.

(e) Subpart Ce—Hospital/Medical/Infectious Waste Incinerators.

[62 FR 48379, Sept. 15, 1997]

§60.31   Definitions.

Terms used but not defined in this subpart have the meaning given them in the Act and in subparts A and B of this part.

[42 FR 55797, Oct. 18, 1977]

Subpart Ca [Reserved]

Subpart Cb—Emissions Guidelines and Compliance Times for Large Municipal Waste Combustors That are Constructed on or Before September 20, 1994

Source: 60 FR 65415, Dec. 19, 1995, unless otherwise noted.

§60.30b   Scope and delegation of authority.

(a) This subpart contains emission guidelines and compliance schedules for the control of certain designated pollutants from certain municipal waste combustors in accordance with section 111(d) and section 129 of the Clean Air Act and subpart B of this part. The provisions in these emission guidelines apply instead of the provisions of §60.24(f) of subpart B of this part.

(b) The following authorities are retained by EPA:

(1) Approval of exemption claims in §60.32b(b)(1), (d), (e), (f)(1), (i)(1);

(2) Approval of a nitrogen oxides trading program under §60.33b(d)(2);

(3) Approval of major alternatives to test methods;

(4) Approval of major alternatives to monitoring;

(5) Waiver of recordkeeping; and

(6) Performance test and data reduction waivers under §608(b).

[71 FR 27332, May 10, 2006]

§60.31b   Definitions.

Terms used but not defined in this subpart have the meaning given them in the Clean Air Act and subparts A, B, and Eb of this part.

EPA means the Administrator of the U.S. EPA or employee of the U.S. EPA who is delegated to perform the specified task.

Municipal waste combustor plant means one or more designated facilities (as defined in §60.32b) at the same location.

Semi-suspension refuse-derived fuel-fired combustor/wet refuse-derived fuel process conversion means a combustion unit that was converted from a wet refuse-derived fuel process to a dry refuse-derived fuel process, and because of constraints in the design of the system, includes a low furnace height (less than 60 feet between the grate and the roof) and a high waste capacity-to-undergrate air zone ratio (greater than 300 tons of waste per day (tpd) fuel per each undergrate air zone).

Spreader stoker fixed floor refuse-derived fuel-fired combustor/100 percent coal capable means a spreader stoker type combustor with a fixed floor grate design that typically fires 100 percent refuse-derived fuel but is equipped to burn 100 percent coal instead of refuse-derived fuel to fulfill 100 percent steam or energy demand.

[60 FR 65415, Dec. 19, 1995, as amended at 62 FR 45119, 45125, Aug. 25, 1997; 71 FR 27332, May 10, 2006]

§60.32b   Designated facilities.

(a) The designated facility to which these guidelines apply is each municipal waste combustor unit with a combustion capacity greater than 250 tons per day of municipal solid waste for which construction was commenced on or before September 20, 1994.

(b) Any municipal waste combustion unit that is capable of combusting more than 250 tons per day of municipal solid waste and is subject to a federally enforceable permit limiting the maximum amount of municipal solid waste that may be combusted in the unit to less than or equal to 11 tons per day is not subject to this subpart if the owner or operator:

(1) Notifies EPA of an exemption claim,

(2) Provides a copy of the federally enforceable permit that limits the firing of municipal solid waste to less than 11 tons per day, and

(3) Keeps records of the amount of municipal solid waste fired on a daily basis.

(c) Physical or operational changes made to an existing municipal waste combustor unit primarily for the purpose of complying with emission guidelines under this subpart are not considered in determining whether the unit is a modified or reconstructed facility under subpart Ea or subpart Eb of this part.

(d) A qualifying small power production facility, as defined in section 3(17)(C) of the Federal Power Act (16 U.S.C. 796(17)(C)), that burns homogeneous waste (such as automotive tires or used oil, but not including refuse-derived fuel) for the production of electric energy is not subject to this subpart if the owner or operator of the facility notifies EPA of this exemption and provides data documenting that the facility qualifies for this exemption.

(e) A qualifying cogeneration facility, as defined in section 3(18)(B) of the Federal Power Act (16 U.S.C. 796(18)(B)), that burns homogeneous waste (such as automotive tires or used oil, but not including refuse-derived fuel) for the production of electric energy and steam or forms of useful energy (such as heat) that are used for industrial, commercial, heating, or cooling purposes, is not subject to this subpart if the owner or operator of the facility notifies EPA of this exemption and provides data documenting that the facility qualifies for this exemption.

(f) Any unit combusting a single-item waste stream of tires is not subject to this subpart if the owner or operator of the unit:

(1) Notifies EPA of an exemption claim, and

(2) Provides data documenting that the unit qualifies for this exemption.

(g) Any unit required to have a permit under section 3005 of the Solid Waste Disposal Act is not subject to this subpart.

(h) Any materials recovery facility (including primary or secondary smelters) that combusts waste for the primary purpose of recovering metals is not subject to this subpart.

(i) Any cofired combustor, as defined under §60.51b of subpart Eb of this part, that meets the capacity specifications in paragraph (a) of this section is not subject to this subpart if the owner or operator of the cofired combustor:

(1) Notifies EPA of an exemption claim,

(2) Provides a copy of the federally enforceable permit (specified in the definition of cofired combustor in this section), and

(3) Keeps a record on a calendar quarter basis of the weight of municipal solid waste combusted at the cofired combustor and the weight of all other fuels combusted at the cofired combustor.

(j) Air curtain incinerators, as defined under §60.51b of subpart Eb of this part, that meet the capacity specifications in paragraph (a) of this section, and that combust a fuel stream composed of 100 percent yard waste are exempt from all provisions of this subpart except the opacity standard under §60.37b, the testing procedures under §60.38b, and the reporting and recordkeeping provisions under §60.39b.

(k) Air curtain incinerators that meet the capacity specifications in paragraph (a) of this section and that combust municipal solid waste other than yard waste are subject to all provisions of this subpart.

(l) Pyrolysis/combustion units that are an integrated part of a plastics/rubber recycling unit (as defined in §60.51b) are not subject to this subpart if the owner or operator of the plastics/rubber recycling unit keeps records of the weight of plastics, rubber, and/or rubber tires processed on a calendar quarter basis; the weight of chemical plant feedstocks and petroleum refinery feedstocks produced and marketed on a calendar quarter basis; and the name and address of the purchaser of the feedstocks. The combustion of gasoline, diesel fuel, jet fuel, fuel oils, residual oil, refinery gas, petroleum coke, liquified petroleum gas, propane, or butane produced by chemical plants or petroleum refineries that use feedstocks produced by plastics/rubber recycling units are not subject to this subpart.

(m) Cement kilns firing municipal solid waste are not subject to this subpart.

(n) Any affected facility meeting the applicability requirements under this section is not subject to subpart E of this part.

[60 FR 65415, Dec. 19, 1995, as amended at 62 FR 45119, 45125, Aug. 25, 1997; 71 FR 27332, May 10, 2006]

§60.33b   Emission guidelines for municipal waste combustor metals, acid gases, organics, and nitrogen oxides.

(a) The emission limits for municipal waste combustor metals are specified in paragraphs (a)(1) through (a)(3) of this section.

(1) For approval, a State plan shall include emission limits for particulate matter and opacity at least as protective as the emission limits for particulate matter and opacity specified in paragraphs (a)(1)(i) through (a)(1)(iii) of this section.

(i) Before April 28, 2009, the emission limit for particulate matter contained in the gases discharged to the atmosphere from a designated facility is 27 milligrams per dry standard cubic meter, corrected to 7 percent oxygen. On and after April 28, 2009, the emission limit for particulate matter contained in the gases discharged to the atmosphere from a designated facility is 25 milligrams per dry standard cubic meter, corrected to 7 percent oxygen.

(ii) [Reserved]

(iii) The emission limit for opacity exhibited by the gases discharged to the atmosphere from a designated facility is 10 percent (6-minute average).

(2) For approval, a State plan shall include emission limits for cadmium at least as protective as the emission limits for cadmium specified in paragraphs (a)(2)(i) through (a)(2)(iv) of this section.

(i) Before April 28, 2009, the emission limit for cadmium contained in the gases discharged to the atmosphere from a designated facility is 40 micrograms per dry standard cubic meter, corrected to 7 percent oxygen. On and after April 28, 2009, the emission limit for cadmium contained in the gases discharged to the atmosphere from a designated facility is 35 micrograms per dry standard cubic meter, corrected to 7 percent oxygen.

(ii) [Reserved]

(3) For approval, a State plan shall include emission limits for mercury at least as protective as the emission limits specified in this paragraph. Before April 28, 2009, the emission limit for mercury contained in the gases discharged to the atmosphere from a designated facility is 80 micrograms per dry standard cubic meter or 15 percent of the potential mercury emission concentration (85-percent reduction by weight), corrected to 7 percent oxygen, whichever is less stringent. On and after April 28, 2009, the emission limit for mercury contained in the gases discharged to the atmosphere from a designated facility is 50 micrograms per dry standard cubic meter or 15 percent of the potential mercury emission concentration (85-percent reduction by weight), corrected to 7 percent oxygen, whichever is less stringent.

(4) For approval, a State plan shall include an emission limit for lead at least as protective as the emission limit for lead specified in this paragraph. Before April 28, 2009, the emission limit for lead contained in the gases discharged to the atmosphere from a designated facility is 440 micrograms per dry standard cubic meter, corrected to 7 percent oxygen. On and after April 28, 2009, the emission limit for lead contained in the gases discharged to the atmosphere from a designated facility is 400 micrograms per dry standard cubic meter, corrected to 7 percent oxygen.

(b) The emission limits for municipal waste combustor acid gases, expressed as sulfur dioxide and hydrogen chloride, are specified in paragraphs (b)(1) and (b)(2) of this section.

(1) For approval, a State plan shall include emission limits for sulfur dioxide at least as protective as the emission limits for sulfur dioxide specified in paragraphs (b)(1)(i) and (b)(1)(ii) of this section.

(i) The emission limit for sulfur dioxide contained in the gases discharged to the atmosphere from a designated facility is 31 parts per million by volume or 25 percent of the potential sulfur dioxide emission concentration (75-percent reduction by weight or volume), corrected to 7 percent oxygen (dry basis), whichever is less stringent. Compliance with this emission limit is based on a 24-hour daily geometric mean.

(ii) [Reserved]

(2) For approval, a State plan shall include emission limits for hydrogen chloride at least as protective as the emission limits for hydrogen chloride specified in paragraphs (b)(2)(i) and (b)(2)(ii) of this section.

(i) The emission limit for hydrogen chloride contained in the gases discharged to the atmosphere from a designated facility is 31 parts per million by volume or 5 percent of the potential hydrogen chloride emission concentration (95-percent reduction by weight or volume), corrected to 7 percent oxygen (dry basis), whichever is less stringent.

(ii) [Reserved]

(3) For approval, a State plan shall be submitted by August 25, 1998 and shall include emission limits for sulfur dioxide and hydrogen chloride at least as protective as the emission limits specified in paragraphs (b)(3)(i) and (b)(3)(ii) of this section.

(i) The emission limit for sulfur dioxide contained in the gases discharged to the atmosphere from a designated facility is 29 parts per million by volume or 25 percent of the potential sulfur dioxide emission concentration (75-percent reduction by weight or volume), corrected to 7 percent oxygen (dry basis), whichever is less stringent. Compliance with this emission limit is based on a 24-hour daily geometric mean.

(ii) The emission limit for hydrogen chloride contained in the gases discharged to the atmosphere from a designated facility is 29 parts per million by volume or 5 percent of the potential hydrogen chloride emission concentration (95-percent reduction by weight or volume), corrected to 7 percent oxygen (dry basis), whichever is less stringent.

(c) The emission limits for municipal waste combustor organics, expressed as total mass dioxin/furan, are specified in paragraphs (c)(1) and (c)(2) of this section.

(1) For approval, a State plan shall include an emission limit for dioxin/furan contained in the gases discharged to the atmosphere from a designated facility at least as protective as the emission limit for dioxin/furan specified in paragraphs (c)(1)(i), (c)(1)(ii), and (c)(1)(iii) of this section, as applicable.

(i) Before April 28, 2009, the emission limit for designated facilities that employ an electrostatic precipitator-based emission control system is 60 nanograms per dry standard cubic meter (total mass), corrected to 7 percent oxygen.

(ii) On and after April 28, 2009, the emission limit for designated facilities that employ an electrostatic precipitator-based emission control system is 35 nanograms per dry standard cubic meter (total mass), corrected to 7 percent oxygen.

(iii) The emission limit for designated facilities that do not employ an electrostatic precipitator-based emission control system is 30 nanograms per dry standard cubic meter (total mass), corrected to 7 percent oxygen.

(d) For approval, a State plan shall include emission limits for nitrogen oxides at least as protective as the emission limits listed in table 1 of this subpart for designated facilities. table 1 provides emission limits for the nitrogen oxides concentration level for each type of designated facility.

(1) A State plan may allow nitrogen oxides emissions averaging as specified in paragraphs (d)(1)(i) through (d)(1)(v) of this section.

(i) The owner or operator of a municipal waste combustor plant may elect to implement a nitrogen oxides emissions averaging plan for the designated facilities that are located at that plant and that are subject to subpart Cb, except as specified in paragraphs (d)(1)(i)(A) and (d)(1)(i)(B) of this section.

(A) Municipal waste combustor units subject to subpart Ea or Eb cannot be included in the emissions averaging plan.

(B) Mass burn refractory municipal waste combustor units and other municipal waste combustor technologies not listed in paragraph (d)(1)(iii) of this section may not be included in the emissions averaging plan.

(ii) The designated facilities included in the nitrogen oxides emissions averaging plan must be identified in the initial compliance report specified in §60.59b(f) or in the annual report specified in §60.59b(g), as applicable, prior to implementing the averaging plan. The designated facilities being included in the averaging plan may be redesignated each calendar year. Partial year redesignation is allowable with State approval.

(iii) To implement the emissions averaging plan, the average daily (24-hour) nitrogen oxides emission concentration level for gases discharged from the designated facilities being included in the emissions averaging plan must be no greater than the levels specified in table 2 of this subpart. table 2 provides emission limits for the nitrogen oxides concentration level for each type of designated facility.

(iv) Under the emissions averaging plan, the average daily nitrogen oxides emissions specified in paragraph (d)(1)(iii) of this section shall be calculated using equation (1). Designated facilities that are offline shall not be included in calculating the average daily nitrogen oxides emission level.

eCFR graphic er19de95.000.gif

View or download PDF

where:

NOX 24-hr = 24-hr daily average nitrogen oxides emission concentration level for the emissions averaging plan (parts per million by volume corrected to 7 percent oxygen).

NOX i-hr = 24-hr daily average nitrogen oxides emission concentration level for designated facility i (parts per million by volume, corrected to 7 percent oxygen), calculated according to the procedures in §60.58b(h) of this subpart.

Si = maximum demonstrated municipal waste combustor unit load for designated facility i (pounds per hour steam or feedwater flow as determined in the most recent dioxin/furan performance test).

h = total number of designated facilities being included in the daily emissions average.

(v) For any day in which any designated facility included in the emissions averaging plan is offline, the owner or operator of the municipal waste combustor plant must demonstrate compliance according to either paragraph (d)(1)(v)(A) of this section or both paragraphs (d)(1)(v)(B) and (d)(1)(v)(C) of this section.

(A) Compliance with the applicable limits specified in table 2 of this subpart shall be demonstrated using the averaging procedure specified in paragraph (d)(1)(iv) of this section for the designated facilities that are online.

(B) For each of the designated facilities included in the emissions averaging plan, the nitrogen oxides emissions on a daily average basis shall be calculated and shall be equal to or less than the maximum daily nitrogen oxides emission level achieved by that designated facility on any of the days during which the emissions averaging plan was achieved with all designated facilities online during the most recent calendar quarter. The requirements of this paragraph do not apply during the first quarter of operation under the emissions averaging plan.

(C) The average nitrogen oxides emissions (kilograms per day) calculated according to paragraph (d)(1)(v)(C)(2) of this section shall not exceed the average nitrogen oxides emissions (kilograms per day) calculated according to paragraph (d)(1)(v)(C)(1) of this section.

(1) For all days during which the emissions averaging plan was implemented and achieved and during which all designated facilities were online, the average nitrogen oxides emissions shall be calculated. The average nitrogen oxides emissions (kilograms per day) shall be calculated on a calendar year basis according to paragraphs (d)(1)(v)(C)(1)(i) through (d)(1)(v)(C)(1)(iii) of this section.

(i) For each designated facility included in the emissions averaging plan, the daily amount of nitrogen oxides emitted (kilograms per day) shall be calculated based on the hourly nitrogen oxides data required under §60.38b(a) and specified under §60.58b(h)(5) of subpart Eb of this part, the flue gas flow rate determined using table 19-1 of EPA Reference Method 19 or a State-approved method, and the hourly average steam or feedwater flow rate.

(ii) The daily total nitrogen oxides emissions shall be calculated as the sum of the daily nitrogen oxides emissions from each designated facility calculated under paragraph (d)(1)(v)(C)(1)(i) of this section.

(iii) The average nitrogen oxides emissions (kilograms per day) on a calendar year basis shall be calculated as the sum of all daily total nitrogen oxides emissions calculated under paragraph (d)(1)(v)(C)(1)(ii) of this section divided by the number of calendar days for which a daily total was calculated.

(2) For all days during which one or more of the designated facilities under the emissions averaging plan was offline, the average nitrogen oxides emissions shall be calculated. The average nitrogen oxides emissions (kilograms per day) shall be calculated on a calendar year basis according to paragraphs (d)(1)(v)(C)(2)(i) through (d)(1)(v)(C)(2)(iii) of this section.

(i) For each designated facility included in the emissions averaging plan, the daily amount of nitrogen oxides emitted (kilograms per day) shall be calculated based on the hourly nitrogen oxides data required under §60.38b(a) and specified under §60.58b(h)(5) of subpart Eb of this part, the flue gas flow rate determined using table 19-1 of EPA Reference Method 19 or a State-approved method, and the hourly average steam or feedwater flow rate.

(ii) The daily total nitrogen oxides emissions shall be calculated as the sum of the daily nitrogen oxides emissions from each designated facility calculated under paragraph (d)(1)(v)(C)(2)(i) of this section.

(iii) The average nitrogen oxides emissions (kilograms per day) on a calendar year basis shall be calculated as the sum of all daily total nitrogen oxides emissions calculated under paragraph (d)(1)(v)(C)(2)(ii) of this section divided by the number of calendar days for which a daily total was calculated.

(2) A State plan may establish a program to allow owners or operators of municipal waste combustor plants to engage in trading of nitrogen oxides emission credits. A trading program must be approved by EPA before implementation.

(3) For approval, a State plan shall include emission limits for nitrogen oxides from fluidized bed combustors at least as protective as the emission limits listed in paragraphs (d)(3)(i) and (d)(3)(ii) of this section.

(i) The emission limit for nitrogen oxides contained in the gases discharged to the atmosphere from a designated facility that is a fluidized bed combustor is 180 parts per million by volume, corrected to 7 percent oxygen.

(ii) If a State plan allows nitrogen oxides emissions averaging as specified in paragraphs (d)(1)(i) through (d)(1)(v) of this section, the emission limit for nitrogen oxides contained in the gases discharged to the atmosphere from a designated facility that is a fluidized bed combustor is 165 parts per million by volume, corrected to 7 percent oxygen.

[60 FR 65415, Dec. 19, 1995, as amended at 62 FR 45119, 45125, Aug. 25, 1997; 71 FR 27333, May 10, 2006]

§60.34b   Emission guidelines for municipal waste combustor operating practices.

(a) For approval, a State plan shall include emission limits for carbon monoxide at least as protective as the emission limits for carbon monoxide listed in table 3 of this subpart. table 3 provides emission limits for the carbon monoxide concentration level for each type of designated facility.

(b) For approval, a State plan shall include requirements for municipal waste combustor operating practices at least as protective as those requirements listed in §60.53b(b) and (c) of subpart Eb of this part.

[60 FR 65415, Dec. 19, 1995, as amended at 62 FR 45120, 45125, Aug. 25, 1997; 69 FR 42121, July 14, 2004; 71 FR 27333, May 10, 2006]

§60.35b   Emission guidelines for municipal waste combustor operator training and certification.

For approval, a State plan shall include requirements for designated facilities for municipal waste combustor operator training and certification at least as protective as those requirements listed in §60.54b of subpart Eb of this part. The State plan shall require compliance with these requirements according to the schedule specified in §60.39b(c)(4).

[60 FR 65415, Dec. 19, 1995, as amended at 62 FR 45120, Aug. 25, 1997]

§60.36b   Emission guidelines for municipal waste combustor fugitive ash emissions.

For approval, a State plan shall include requirements for municipal waste combustor fugitive ash emissions at least as protective as those requirements listed in §60.55b of subpart Eb of this part.

§60.37b   Emission guidelines for air curtain incinerators.

For approval, a State plan shall include emission limits for opacity for air curtain incinerators at least as protective as those listed in §60.56b of subpart Eb of this part.

§60.38b   Compliance and performance testing.

(a) For approval, a State plan shall include the performance testing methods listed in §60.58b of subpart Eb of this part, as applicable, except as provided for under §60.24(b)(2) of subpart B of this part and paragraphs (b) and (c) of this section.

(b) For approval, a State plan shall include for designated facilities the alternative performance testing schedule for dioxins/furans specified in §60.58b(g)(5)(iii) of subpart Eb of this part, as applicable, for those designated facilities that achieve a dioxin/furan emission level less than or equal to 15 nanograms per dry standard cubic meter total mass, corrected to 7 percent oxygen.

(c) [Reserved]

[60 FR 65415, Dec. 19, 1995, as amended at 62 FR 45120, Aug. 25, 1997]

§60.39b   Reporting and recordkeeping guidelines and compliance schedules.

(a) For approval, a State plan shall include the reporting and recordkeeping provisions listed in §60.59b of subpart Eb of this part, as applicable, except for the siting requirements under §60.59b(a), (b)(5), and (d)(11) of subpart Eb of this part.

(b) Except as provided in paragraph (e) of this section, not later than December 19, 1996, each State in which a designated facility is located shall submit to EPA a plan to implement and enforce all provisions of this subpart except the revised April 28, 2009 emission limits in §60.33b(a), (c), and (d). Not later than April 28, 2007, each State in which a designated facility is located shall submit to EPA a plan to implement and enforce all provisions of this subpart, as amended on May 10, 2006. The submittal schedule specified in this paragraph is in accordance with section 129(b)(2) of the Clean Air Act and applies instead of the schedule provided in §60.23(a)(1) of subpart B of this part.

(c) For approval, a State plan that is submitted prior to May 10, 2006 shall include the compliance schedules specified in paragraphs (c)(1) through (c)(5) of this section.

(1) A State plan shall allow designated facilities to comply with all requirements of a State plan (or close) within 1 year after approval of the State plan, except as provided by paragraph (c)(1)(i) and (c)(1)(ii) of this section.

(i) A State plan that allows designated facilities more than 1 year but less than 3 years following the date of issuance of a revised construction or operation permit, if a permit modification is required, or more than 1 year but less than 3 years following approval of the State plan, if a permit modification is not required, shall include measurable and enforceable incremental steps of progress toward compliance. Suggested measurable and enforceable activities are specified in paragraphs (c)(1)(i)(A) through (c)(1)(i)(J) of this section.

(A) Date for obtaining services of an architectural and engineering firm regarding the air pollution control device(s);

(B) Date for obtaining design drawings of the air pollution control device(s);

(C) Date for submittal of permit modifications, if necessary;

(D) Date for submittal of the final control plan to the Administrator. [§60.21 (h)(1) of subpart B of this part.];

(E) Date for ordering the air pollution control device(s);

(F) Date for obtaining the major components of the air pollution control device(s);

(G) Date for initiation of site preparation for installation of the air pollution control device(s);

(H) Date for initiation of installation of the air pollution control device(s);

(I) Date for initial startup of the air pollution control device(s); and

(J) Date for initial performance test(s) of the air pollution control device(s).

(ii) A State plan that allows designated facilities more than 1 year but up to 3 years after State plan approval to close shall require a closure agreement. The closure agreement must include the date of plant closure.

(2) If the State plan requirements for a designated facility include a compliance schedule longer than 1 year after approval of the State plan in accordance with paragraph (c)(1)(i) or (c)(1)(ii) of this section, the State plan submittal (for approval) shall include performance test results for dioxin/furan emissions for each designated facility that has a compliance schedule longer than 1 year following the approval of the State plan, and the performance test results shall have been conducted during or after 1990. The performance test shall be conducted according to the procedures in §60.38b.

(3) [Reserved]

(4) A State plan shall require compliance with the municipal waste combustor operator training and certification requirements under §60.35b according to the schedule specified in paragraphs (c)(4)(i) through (c)(4)(iii) of this section.

(i) [Reserved]

(ii) For designated facilities, the State plan shall require compliance with the municipal waste combustor operator training and certification requirements specified under §60.54b (a) through (c) of subpart Eb of this part by the date 6 months after the date of startup or 12 months after State plan approval, whichever is later.

(iii) For designated facilities, the State plan shall require compliance with the requirements specified in §60.54b (d), (f), and (g) of subpart Eb of this part no later than 6 months after startup or 12 months after State plan approval, whichever is later.

(A) The requirement specified in §60.54b(d) of subpart Eb of this part does not apply to chief facility operators, shift supervisors, and control room operators who have obtained full certification from the American Society of Mechanical Engineers on or before the date of State plan approval.

(B) The owner or operator of a designated facility may request that the Administrator waive the requirement specified in §60.54b(d) of subpart Eb of this part for chief facility operators, shift supervisors, and control room operators who have obtained provisional certification from the American Society of Mechanical Engineers on or before the initial date of State plan approval.

(C) The initial training requirements specified in §60.54b(f)(1) of subpart Eb of this part shall be completed no later than the date specified in paragraph (c)(4)(iii)(C)(1), (c)(4)(iii)(C)(2), or (c)(4)(iii)(C)(3), of this section whichever is later.

(1) The date 6 months after the date of startup of the affected facility;

(2) Twelve months after State plan approval; or

(3) The date prior to the day when the person assumes responsibilities affecting municipal waste combustor unit operation.

(5) A State plan shall require all designated facilities for which construction, modification, or reconstruction is commenced after June 26, 1987 to comply with the emission limit for mercury specified in §60.33b(a)(3) and the emission limit for dioxins/furans specified in §60.33b(c)(1) within 1 year following issuance of a revised construction or operation permit, if a permit modification is required, or within 1 year following approval of the State plan, whichever is later.

(d) In the event no plan for implementing the emission guidelines is approved by EPA, all designated facilities meeting the applicability requirements under §60.32b shall be in compliance with all of the guidelines, except those specified under §60.33b (a)(4), (b)(3), and (d)(3), no later than December 19, 2000.

(e) Not later than August 25, 1998, each State in which a designated facility is operating shall submit to EPA a plan to implement and enforce all provisions of this subpart specified in §60.33b(b)(3) and (d)(3) and the emission limit in paragraph (a)(4) that applies before April 28, 2009.

(f) In the event no plan for implementing the emission guidelines is approved by EPA, all designated facilities meeting the applicability requirements under §60.32b shall be in compliance with all of the guidelines, including those specified under §60.33b (a)(4), (b)(3), and (d)(3), no later than August 26, 2002.

(g) For approval, a revised State plan submitted not later than April 28, 2007 in accordance with paragraph (b) of this section, shall include compliance schedules for meeting the revised April 28, 2009 emission limits in §60.33b(a), (c), and (d) and the revised testing provisions in §60.38b(b).

(1) Compliance with the revised April 28, 2009 emission limits is required as expeditiously as practicable, but no later than April 28, 2009, except as provided in paragraph (g)(2) of this section.

(2) The owner or operator of an affected facility who is planning an extensive emission control system upgrade may petition the Administrator for a longer compliance schedule and must demonstrate to the satisfaction of the Administrator the need for the additional time. If approved, the schedule may exceed the schedule in paragraph (g)(1) of this section, but cannot exceed May 10, 2011.

(h) In the event no plan for implementing the emission guidelines is approved by EPA, all designated facilities meeting the applicability requirements under §60.32b shall be in compliance with all of the guidelines, including the revised April 28, 2009 emission limits in §60.33b(a), (b), (c), (d), and §60.34b(a), and the revised testing provisions in §60.38b(b), no later than May 10, 2011.

[60 FR 65415, Dec. 19, 1995, as amended at 62 FR 45120, 45125, Aug. 25, 1997; 71 FR 27333, May 10, 2006]

Table 1 to Subpart Cb of Part 60—Nitrogen Oxides Guidelines for Designated Facilities

Municipal waste combustor technology Before April 28, 2009,
nitrogen oxides emission limit
(parts per million by volume)a
On and after April 28, 2009,
nitrogen oxides emission limit
(parts per million by volume)a
Mass burn waterwall205205.
Mass burn rotary waterwall250210.
Refuse-derived fuel combustor250250.
Fluidized bed combustor180180.
Mass burn refractory combustorsNo limitNo limit.

aCorrected to 7 percent oxygen, dry basis.

[71 FR 27334, May 10, 2006]

Table 2 to Subpart Cb of Part 60—Nitrogen Oxides Limits for Existing Designated Facilities Included in an Emissions Averaging Plan at a Municipal Waste Combustor Plantb

Municipal waste combustor technology Before April 28, 2009, nitrogen
oxides emission
limit (parts per
million by
volume)b
On and after April 28, 2009, nitrogen oxides emission limit (parts per
million by
volume)a
Mass burn waterwall185185
Mass burn rotary waterwall220190
Refuse-derived fuel combustor230230
Fluidized bed combustor165165

aMass burn refractory municipal waste combustors and other MWC technologies not listed above may not be included in an emissions averaging plan.

bCorrected to 7 percent oxygen, dry basis.

[71 FR 27334, May 10, 2006]

Table 3 to Subpart Cb of Part 60—Municipal Waste Combustor Operating Guidelines

Municipal waste combustor technology Carbon monoxide emissions levels (parts per million by volume)a Averaging time (hrs)b
Mass burn waterwall1004
Mass burn refractory1004
Mass burn rotary refractory10024
Mass burn rotary waterwall25024
Modular starved air504
Modular excess air504
Refuse-derived fuel stoker20024
Fluidized bed, mixed fuel (wood/refuse-derived fuel)200c24
Bubbling fluidized bed combustor1004
Circulating fluidized bed combustor1004
Pulverized coal/refuse-derived fuel mixed fuel-fired combustor1504
Spreader stoker coal/refuse-derived fuel mixed fuel-fired combustor20024
Semi-suspension refuse-derived fuel-fired combustor/wet refuse-derived fuel process conversion250c24
Spreader stoker fixed floor refuse-derived fuel-fired combustor/100 percent coal capable250c24

aMeasured at the combustor outlet in conjunction with a measurement of oxygen concentration, corrected to 7 percent oxygen, dry basis. Calculated as an arithmetic average.

bAveraging times are 4-hour or 24-hour block averages.

c24-hour block average, geometric mean.

[71 FR 27334, May 10, 2006]

Subpart Cc—Emission Guidelines and Compliance Times for Municipal Solid Waste Landfills

Source: 61 FR 9919, Mar. 12, 1996, unless otherwise noted.

§60.30c   Scope.

This subpart contains emission guidelines and compliance times for the control of certain designated pollutants from certain designated municipal solid waste landfills in accordance with section 111(d) of the Act and subpart B.

§60.31c   Definitions.

Terms used but not defined in this subpart have the meaning given them in the Act and in subparts A, B, and WWW of this part.

Municipal solid waste landfill or MSW landfill means an entire disposal facility in a contiguous geographical space where household waste is placed in or on land. An MSW landfill may also receive other types of RCRA Subtitle D wastes such as commercial solid waste, nonhazardous sludge, conditionally exempt small quantity generator waste, and industrial solid waste. Portions of an MSW landfill may be separated by access roads. An MSW landfill may be publicly or privately owned. An MSW landfill may be a new MSW landfill, an existing MSW landfill or a lateral expansion.

§60.32c   Designated facilities.

(a) The designated facility to which the guidelines apply is each existing MSW landfill for which construction, reconstruction or modification was commenced before May 30, 1991.

(b) Physical or operational changes made to an existing MSW landfill solely to comply with an emission guideline are not considered a modification or reconstruction and would not subject an existing MSW landfill to the requirements of subpart WWW [see §60.750 of subpart WWW].

(c) For purposes of obtaining an operating permit under title V of the Act, the owner or operator of a MSW landfill subject to this subpart with a design capacity less than 2.5 million megagrams or 2.5 million cubic meters is not subject to the requirement to obtain an operating permit for the landfill under part 70 or 71 of this chapter, unless the landfill is otherwise subject to either part 70 or 71. For purposes of submitting a timely application for an operating permit under part 70 or 71, the owner or operator of a MSW landfill subject to this subpart with a design capacity greater than or equal to 2.5 million megagrams and 2.5 million cubic meters on the effective date of EPA approval of the State's program under section 111(d) of the Act, and not otherwise subject to either part 70 or 71, becomes subject to the requirements of §§70.5(a)(1)(i) or 71.5(a)(1)(i) of this chapter 90 days after the effective date of such 111(d) program approval, even if the design capacity report is submitted earlier.

(d) When a MSW landfill subject to this subpart is closed, the owner or operator is no longer subject to the requirement to maintain an operating permit under part 70 or 71 of this chapter for the landfill if the landfill is not otherwise subject to the requirements of either part 70 or 71 and if either of the following conditions are met.

(1) The landfill was never subject to the requirement for a control system under §60.33c(c) of this subpart; or

(2) The owner or operator meets the conditions for control system removal specified in §60.752(b)(2)(v) of subpart WWW.

[61 FR 9919, Mar. 12, 1996, as amended at 63 FR 32750, June 16, 1998]

§60.33c   Emission guidelines for municipal solid waste landfill emissions.

(a) For approval, a State plan shall include control of MSW landfill emissions at each MSW landfill meeting the following three conditions:

(1) The landfill has accepted waste at any time since November 8, 1987, or has additional design capacity available for future waste deposition;

(2) The landfill has a design capacity greater than or equal to 2.5 million megagrams and 2.5 million cubic meters. The landfill may calculate design capacity in either megagrams or cubic meters for comparison with the exemption values. Any density conversions shall be documented and submitted with the design capacity report; and

(3) The landfill has a nonmethane organic compound emission rate of 50 megagrams per year or more.

(b) For approval, a State plan shall include the installation of a collection and control system meeting the conditions provided in §60.752(b)(2)(ii) of this part at each MSW landfill meeting the conditions in paragraph (a) of this section. The State plan shall include a process for State review and approval of the site-specific design plans for the gas collection and control system(s).

(c) For approval, a State plan shall include provisions for the control of collected MSW landfill emissions through the use of control devices meeting the requirements of paragraph (c)(1), (2), or (3) of this section, except as provided in §60.24.

(1) An open flare designed and operated in accordance with the parameters established in §60.18; or

(2) A control system designed and operated to reduce NMOC by 98 weight percent; or

(3) An enclosed combustor designed and operated to reduce the outlet NMOC concentration to 20 parts per million as hexane by volume, dry basis at 3 percent oxygen, or less.

(d) For approval, a State plan shall require each owner or operator of an MSW landfill having a design capacity less than 2.5 million megagrams by mass or 2.5 million cubic meters by volume to submit an initial design capacity report to the Administrator as provided in §60.757(a)(2) of subpart WWW by the date specified in §60.35c of this subpart. The landfill may calculate design capacity in either megagrams or cubic meters for comparison with the exemption values. Any density conversions shall be documented and submitted with the report. Submittal of the initial design capacity report shall fulfill the requirements of this subpart except as provided in paragraph (d)(1) and (d)(2) of this section.

(1) The owner or operator shall submit an amended design capacity report as provided in §60.757(a)(3) of subpart WWW. [Guidance: Note that if the design capacity increase is the result of a modification, as defined in §60.751 of subpart WWW, that was commenced on or after May 30, 1991, the landfill will become subject to subpart WWW instead of this subpart. If the design capacity increase is the result of a change in operating practices, density, or some other change that is not a modification, the landfill remains subject to this subpart.]

(2) When an increase in the maximum design capacity of a landfill with an initial design capacity less than 2.5 million megagrams or 2.5 million cubic meters results in a revised maximum design capacity equal to or greater than 2.5 million megagrams and 2.5 million cubic meters, the owner or operator shall comply with paragraph (e) of this section.

(e) For approval, a State plan shall require each owner or operator of an MSW landfill having a design capacity equal to or greater than 2.5 million megagrams and 2.5 million cubic meters to either install a collection and control system as provided in paragraph (b) of this section and §60.752(b)(2) of subpart WWW or calculate an initial NMOC emission rate for the landfill using the procedures specified in §60.34c of this subpart and §60.754 of subpart WWW. The NMOC emission rate shall be recalculated annually, except as provided in §60.757(b)(1)(ii) of subpart WWW.

(1) If the calculated NMOC emission rate is less than 50 megagrams per year, the owner or operator shall:

(i) Submit an annual emission report, except as provided for in §60.757(b)(1)(ii); and

(ii) Recalculate the NMOC emission rate annually using the procedures specified in §60.754(a)(1) of subpart WWW until such time as the calculated NMOC emission rate is equal to or greater than 50 megagrams per year, or the landfill is closed.

(2)(i) If the NMOC emission rate, upon initial calculation or annual recalculation required in paragraph (e)(1)(ii) of this section, is equal to or greater than 50 megagrams per year, the owner or operator shall install a collection and control system as provided in paragraph (b) of this section and §60.752(b)(2) of subpart WWW.

(ii) If the landfill is permanently closed, a closure notification shall be submitted to the Administrator as provided in §60.35c of this subpart and §60.757(d) of subpart WWW.

[61 FR 9919, Mar. 12, 1996, as amended at 63 FR 32750, June 16, 1998; 64 FR 9261, Feb. 24, 1999]

§60.34c   Test methods and procedures.

For approval, a State plan shall include provisions for: the calculation of the landfill NMOC emission rate listed in §60.754, as applicable, to determine whether the landfill meets the condition in §60.33c(a)(3); the operational standards in §60.753; the compliance provisions in §60.755; and the monitoring provisions in §60.756.

§60.35c   Reporting and recordkeeping guidelines.

For approval, a State plan shall include the recordkeeping and reporting provisions listed in §§60.757 and 60.758, as applicable, except as provided under §60.24.

(a) For existing MSW landfills subject to this subpart the initial design capacity report shall be submitted no later than 90 days after the effective date of EPA approval of the State's plan under section 111(d) of the Act.

(b) For existing MSW landfills covered by this subpart with a design capacity equal to or greater than 2.5 million megagrams and 2.5 million cubic meters, the initial NMOC emission rate report shall be submitted no later than 90 days after the effective date of EPA approval of the State's plan under section 111(d) of the Act.

[61 FR 9919, Mar. 12, 1996, as amended at 64 FR 9262, Feb. 24, 1999]

§60.36c   Compliance times.

(a) Except as provided for under paragraph (b) of this section, planning, awarding of contracts, and installation of MSW landfill air emission collection and control equipment capable of meeting the emission guidelines established under §60.33c shall be accomplished within 30 months after the date the initial NMOC emission rate report shows NMOC emissions equal or exceed 50 megagrams per year.

(b) For each existing MSW landfill meeting the conditions in §60.33c(a)(1) and §60.33c(a)(2) whose NMOC emission rate is less than 50 megagrams per year on the effective date of the State emission standard, installation of collection and control systems capable of meeting emission guidelines in §60.33c shall be accomplished within 30 months of the date when the condition in §60.33c(a)(3) is met (i.e., the date of the first annual nonmethane organic compounds emission rate which equals or exceeds 50 megagrams per year).

[61 FR 9919, Mar. 12, 1996, as amended at 63 FR 32750, June 16, 1998]

Subpart Cd—Emissions Guidelines and Compliance Times for Sulfuric Acid Production Units

Source: 60 FR 65414, Dec. 19, 1995, unless otherwise noted.

§60.30d   Designated facilities.

Sulfuric acid production units. The designated facility to which §§60.31d and 60.32d apply is each existing “sulfuric acid production unit” as defined in §60.81(a) of subpart H of this part.

§60.31d   Emissions guidelines.

Sulfuric acid production units. The emission guideline for designated facilities is 0.25 grams sulfuric acid mist (as measured by EPA Reference Method 8 of appendix A of this part) per kilogram (0.5 pounds per ton) of sulfuric acid produced, the production being expressed as 100 percent sulfuric acid.

§60.32d   Compliance times.

Sulfuric acid production units. Planning, awarding of contracts, and installation of equipment capable of attaining the level of the emission guideline established under §60.31d can be accomplished within 17 months after the effective date of a State emission standard for sulfuric acid mist.

Subpart Ce—Emission Guidelines and Compliance Times for Hospital/Medical/Infectious Waste Incinerators

Source: 62 FR 48379, Sept. 15, 1997, unless otherwise noted.

§60.30e   Scope.

This subpart contains emission guidelines and compliance times for the control of certain designated pollutants from hospital/medical/infectious waste incinerator(s) (HMIWI) in accordance with sections 111 and 129 of the Clean Air Act and subpart B of this part. The provisions in these emission guidelines supersede the provisions of §60.24(f) of subpart B of this part.

§60.31e   Definitions.

Terms used but not defined in this subpart have the meaning given them in the Clean Air Act and in subparts A, B, and Ec of this part.

Standard Metropolitan Statistical Area or SMSA means any areas listed in OMB Bulletin No. 93-17 entitled “Revised Statistical Definitions for Metropolitan Areas” dated June 30, 1993 (incorporated by reference, see §60.17).

§60.32e   Designated facilities.

(a) Except as provided in paragraphs (b) through (h) of this section, the designated facility to which the guidelines apply is each individual HMIWI:

(1) For which construction was commenced on or before June 20, 1996, or for which modification was commenced on or before March 16, 1998.

(2) For which construction was commenced after June 20, 1996 but no later than December 1, 2008, or for which modification is commenced after March 16, 1998 but no later than April 6, 2010.

(b) A combustor is not subject to this subpart during periods when only pathological waste, low-level radioactive waste, and/or chemotherapeutic waste (all defined in §60.51c) is burned, provided the owner or operator of the combustor:

(1) Notifies the Administrator of an exemption claim; and

(2) Keeps records on a calendar quarter basis of the periods of time when only pathological waste, low-level radioactive waste, and/or chemotherapeutic waste is burned.

(c) Any co-fired combustor (defined in §60.51c) is not subject to this subpart if the owner or operator of the co-fired combustor:

(1) Notifies the Administrator of an exemption claim;

(2) Provides an estimate of the relative weight of hospital waste, medical/infectious waste, and other fuels and/or wastes to be combusted; and

(3) Keeps records on a calendar quarter basis of the weight of hospital waste and medical/infectious waste combusted, and the weight of all other fuels and wastes combusted at the co-fired combustor.

(d) Any combustor required to have a permit under Section 3005 of the Solid Waste Disposal Act is not subject to this subpart.

(e) Any combustor which meets the applicability requirements under subpart Cb, Ea, or Eb of this part (standards or guidelines for certain municipal waste combustors) is not subject to this subpart.

(f) Any pyrolysis unit (defined in §60.51c) is not subject to this subpart.

(g) Cement kilns firing hospital waste and/or medical/infectious waste are not subject to this subpart.

(h) Physical or operational changes made to an existing HMIWI unit solely for the purpose of complying with emission guidelines under this subpart are not considered a modification and do not result in an existing HMIWI unit becoming subject to the provisions of subpart Ec (see §60.50c).

(i) Beginning September 15, 2000, or on the effective date of an EPA approved operating permit program under Clean Air Act title V and the implementing regulations under 40 CFR part 70 in the State in which the unit is located, whichever date is later, designated facilities subject to this subpart shall operate pursuant to a permit issued under the EPA-approved operating permit program.

(j) The requirements of this subpart as promulgated on September 15, 1997, shall apply to the designated facilities defined in paragraph (a)(1) of this section until the applicable compliance date of the requirements of this subpart, as amended on October 6, 2009. Upon the compliance date of the requirements of this subpart, designated facilities as defined in paragraph (a)(1) of this section are no longer subject to the requirements of this subpart, as promulgated on September 15, 1997, but are subject to the requirements of this subpart, as amended on October 6, 2009.

(k) The authorities listed under §60.50c(i) shall be retained by the Administrator and not be transferred to a state.

[60 FR 65414, Dec. 19, 1995, as amended at 74 FR 51402, Oct. 6, 2009; 76 FR 18412, Apr. 4, 2011]

§60.33e   Emissions guidelines.

(a) For approval, a State plan shall include the requirements for emissions limits at least as protective as the following requirements, as applicable:

(1) For a designated facility as defined in §60.32e(a)(1) subject to the emissions guidelines as promulgated on September 15, 1997, the requirements listed in Table 1A of this subpart, except as provided in paragraph (b) of this section.

(2) For a designated facility as defined in §60.32e(a)(1) subject to the emissions guidelines as amended on October 6, 2009, the requirements listed in Table 1B of this subpart, except as provided in paragraph (b) of this section.

(3) For a designated facility as defined in §60.32e(a)(2), the more stringent of the requirements listed in Table 1B of this subpart and Table 1A of subpart Ec of this part.

(b) For approval, a State plan shall include the requirements for emissions limits for any small HMIWI constructed on or before June 20, 1996, which is located more than 50 miles from the boundary of the nearest Standard Metropolitan Statistical Area (defined in §60.31e) and which burns less than 2,000 pounds per week of hospital waste and medical/infectious waste that are at least as protective as the requirements in paragraphs (b)(1) and (b)(2) of this section, as applicable. The 2,000 lb/week limitation does not apply during performance tests.

(1) For a designated facility as defined in §60.32e(a)(1) subject to the emissions guidelines as promulgated on September 15, 1997, the requirements listed in Table 2A of this subpart.

(2) For a designated facility as defined in §60.32e(a)(1) subject to the emissions guidelines as amended on October 6, 2009, the requirements listed in Table 2B of this subpart.

(c) For approval, a State plan shall include the requirements for stack opacity at least as protective as the following, as applicable:

(1) For a designated facility as defined in §60.32e(a)(1) subject to the emissions guidelines as promulgated on September 15, 1997, the requirements in §60.52c(b)(1) of subpart Ec of this part.

(2) For a designated facility as defined in §60.32e(a)(1) subject to the emissions guidelines as amended on October 6, 2009 and a designated facility as defined in §60.32e(a)(2), the requirements in §60.52c(b)(2) of subpart Ec of this part.

[74 FR 51403, Oct. 6, 2009]

§60.34e   Operator training and qualification guidelines.

For approval, a State plan shall include the requirements for operator training and qualification at least as protective as those requirements listed in §60.53c of subpart Ec of this part. The State plan shall require compliance with these requirements according to the schedule specified in §60.39e(e).

§60.35e   Waste management guidelines.

For approval, a State plan shall include the requirements for a waste management plan at least as protective as those requirements listed in §60.55c of subpart Ec of this part.

§60.36e   Inspection guidelines.

(a) For approval, a State plan shall require each small HMIWI subject to the emissions limits under §60.33e(b) and each HMIWI subject to the emissions limits under §60.33e(a)(2) and (a)(3) to undergo an initial equipment inspection that is at least as protective as the following within 1 year following approval of the State plan:

(1) At a minimum, an inspection shall include the following:

(i) Inspect all burners, pilot assemblies, and pilot sensing devices for proper operation; clean pilot flame sensor, as necessary;

(ii) Ensure proper adjustment of primary and secondary chamber combustion air, and adjust as necessary;

(iii) Inspect hinges and door latches, and lubricate as necessary;

(iv) Inspect dampers, fans, and blowers for proper operation;

(v) Inspect HMIWI door and door gaskets for proper sealing;

(vi) Inspect motors for proper operation;

(vii) Inspect primary chamber refractory lining; clean and repair/replace lining as necessary;

(viii) Inspect incinerator shell for corrosion and/or hot spots;

(ix) Inspect secondary/tertiary chamber and stack, clean as necessary;

(x) Inspect mechanical loader, including limit switches, for proper operation, if applicable;

(xi) Visually inspect waste bed (grates), and repair/seal, as appropriate;

(xii) For the burn cycle that follows the inspection, document that the incinerator is operating properly and make any necessary adjustments;

(xiii) Inspect air pollution control device(s) for proper operation, if applicable;

(xiv) Inspect waste heat boiler systems to ensure proper operation, if applicable;

(xv) Inspect bypass stack components;

(xvi) Ensure proper calibration of thermocouples, sorbent feed systems and any other monitoring equipment; and

(xvii) Generally observe that the equipment is maintained in good operating condition.

(2) Within 10 operating days following an equipment inspection all necessary repairs shall be completed unless the owner or operator obtains written approval from the State agency establishing a date whereby all necessary repairs of the designated facility shall be completed.

(b) For approval, a State plan shall require each small HMIWI subject to the emissions limits under §60.33e(b) and each HMIWI subject to the emissions limits under §60.33e(a)(2) and (a)(3) to undergo an equipment inspection annually (no more than 12 months following the previous annual equipment inspection), as outlined in paragraph (a) of this section.

(c) For approval, a State plan shall require each small HMIWI subject to the emissions limits under §60.33e(b)(2) and each HMIWI subject to the emissions limits under §60.33e(a)(2) and (a)(3) to undergo an initial air pollution control device inspection, as applicable, that is at least as protective as the following within 1 year following approval of the State plan:

(1) At a minimum, an inspection shall include the following:

(i) Inspect air pollution control device(s) for proper operation, if applicable;

(ii) Ensure proper calibration of thermocouples, sorbent feed systems, and any other monitoring equipment; and

(iii) Generally observe that the equipment is maintained in good operating condition.

(2) Within 10 operating days following an air pollution control device inspection, all necessary repairs shall be completed unless the owner or operator obtains written approval from the State agency establishing a date whereby all necessary repairs of the designated facility shall be completed.

(d) For approval, a State plan shall require each small HMIWI subject to the emissions limits under §60.33e(b)(2) and each HMIWI subject to the emissions limits under §60.33e(a)(2) and (a)(3) to undergo an air pollution control device inspection, as applicable, annually (no more than 12 months following the previous annual air pollution control device inspection), as outlined in paragraph (c) of this section.

[60 FR 65414, Dec. 19, 1995, as amended at 74 FR 51403, Oct. 6, 2009]

§60.37e   Compliance, performance testing, and monitoring guidelines.

(a) Except as provided in paragraph (b) of this section, for approval, a State plan shall include the requirements for compliance and performance testing listed in §60.56c of subpart Ec of this part, with the following exclusions:

(1) For a designated facility as defined in §60.32e(a)(1) subject to the emissions limits in §60.33e(a)(1), the test methods listed in §60.56c(b)(7) and (8), the fugitive emissions testing requirements under §60.56c(b)(14) and (c)(3), the CO CEMS requirements under §60.56c(c)(4), and the compliance requirements for monitoring listed in §60.56c(c)(5)(ii) through (v), (c)(6), (c)(7), (e)(6) through (10), (f)(7) through (10), (g)(6) through (10), and (h).

(2) For a designated facility as defined in §60.32e(a)(1) and (a)(2) subject to the emissions limits in §60.33e(a)(2) and (a)(3), the annual fugitive emissions testing requirements under §60.56c(c)(3), the CO CEMS requirements under §60.56c(c)(4), and the compliance requirements for monitoring listed in §60.56c(c)(5)(ii) through (v), (c)(6), (c)(7), (e)(6) through (10), (f)(7) through (10), and (g)(6) through (10). Sources subject to the emissions limits under §60.33e(a)(2) and (a)(3) may, however, elect to use CO CEMS as specified under §60.56c(c)(4) or bag leak detection systems as specified under §60.57c(h).

(b) Except as provided in paragraphs (b)(1) and (b)(2) of this section, for approval, a State plan shall require each small HMIWI subject to the emissions limits under §60.33e(b) to meet the performance testing requirements listed in §60.56c of subpart Ec of this part. The 2,000 lb/week limitation under §60.33e(b) does not apply during performance tests.

(1) For a designated facility as defined in §60.32e(a)(1) subject to the emissions limits under §60.33e(b)(1), the test methods listed in §60.56c(b)(7), (8), (12), (13) (Pb and Cd), and (14), the annual PM, CO, and HCl emissions testing requirements under §60.56c(c)(2), the annual fugitive emissions testing requirements under §60.56c(c)(3), the CO CEMS requirements under §60.56c(c)(4), and the compliance requirements for monitoring listed in §60.56c(c)(5) through (7), and (d) through (k) do not apply.

(2) For a designated facility as defined in §60.32e(a)(2) subject to the emissions limits under §60.33e(b)(2), the annual fugitive emissions testing requirements under §60.56c(c)(3), the CO CEMS requirements under §60.56c(c)(4), and the compliance requirements for monitoring listed in §60.56c(c)(5)(ii) through (v), (c)(6), (c)(7), (e)(6) through (10), (f)(7) through (10), and (g)(6) through (10) do not apply. Sources subject to the emissions limits under §60.33e(b)(2) may, however, elect to use CO CEMS as specified under §60.56c(c)(4) or bag leak detection systems as specified under §60.57c(h).

(c) For approval, a State plan shall require each small HMIWI subject to the emissions limits under §60.33e(b) that is not equipped with an air pollution control device to meet the following compliance and performance testing requirements:

(1) Establish maximum charge rate and minimum secondary chamber temperature as site-specific operating parameters during the initial performance test to determine compliance with applicable emission limits.

(2) Following the date on which the initial performance test is completed or is required to be completed under §60.8, whichever date comes first, ensure that the designated facility does not operate above the maximum charge rate or below the minimum secondary chamber temperature measured as 3-hour rolling averages (calculated each hour as the average of the previous 3 operating hours) at all times. Operating parameter limits do not apply during performance tests. Operation above the maximum charge rate or below the minimum secondary chamber temperature shall constitute a violation of the established operating parameter(s).

(3) Except as provided in paragraph (c)(4) of this section, operation of the designated facility above the maximum charge rate and below the minimum secondary chamber temperature (each measured on a 3-hour rolling average) simultaneously shall constitute a violation of the PM, CO, and dioxin/furan emissions limits.

(4) The owner or operator of a designated facility may conduct a repeat performance test within 30 days of violation of applicable operating parameter(s) to demonstrate that the designated facility is not in violation of the applicable emissions limit(s). Repeat performance tests conducted pursuant to this paragraph must be conducted under process and control device operating conditions duplicating as nearly as possible those that indicated a violation under paragraph (c)(3) of this section.

(d) For approval, a State plan shall include the requirements for monitoring listed in §60.57c of subpart Ec of this part for HMIWI subject to the emissions limits under §60.33e(a) and (b), except as provided for under paragraph (e) of this section.

(e) For approval, a State plan shall require small HMIWI subject to the emissions limits under §60.33e(b) that are not equipped with an air pollution control device to meet the following monitoring requirements:

(1) Install, calibrate (to manufacturers' specifications), maintain, and operate a device for measuring and recording the temperature of the secondary chamber on a continuous basis, the output of which shall be recorded, at a minimum, once every minute throughout operation.

(2) Install, calibrate (to manufacturers' specifications), maintain, and operate a device which automatically measures and records the date, time, and weight of each charge fed into the HMIWI.

(3) The owner or operator of a designated facility shall obtain monitoring data at all times during HMIWI operation except during periods of monitoring equipment malfunction, calibration, or repair. At a minimum, valid monitoring data shall be obtained for 75 percent of the operating hours per day for 90 percent of the operating hours per calendar quarter that the designated facility is combusting hospital waste and/or medical/infectious waste.

(f) The owner or operator of a designated facility as defined in §60.32e(a)(1) or (a)(2) subject to emissions limits under §60.33e(a)(2), (a)(3), or (b)(2) may use the results of previous emissions tests to demonstrate compliance with the emissions limits, provided that the conditions in paragraphs (f)(1) through (f)(3) of this section are met:

(1) The designated facility's previous emissions tests must have been conducted using the applicable procedures and test methods listed in §60.56c(b) of subpart Ec of this part. Previous emissions test results obtained using EPA-accepted voluntary consensus standards are also acceptable.

(2) The HMIWI at the designated facility shall currently be operated in a manner (e.g., with charge rate, secondary chamber temperature, etc.) that would be expected to result in the same or lower emissions than observed during the previous emissions test(s), and the HMIWI may not have been modified such that emissions would be expected to exceed (notwithstanding normal test-to-test variability) the results from previous emissions test(s).

(3) The previous emissions test(s) must have been conducted in 1996 or later.

[60 FR 65414, Dec. 19, 1995, as amended at 74 FR 51403, Oct. 6, 2009]

§60.38e   Reporting and recordkeeping guidelines.

(a) Except as provided in paragraphs (a)(1) and (a)(2) of this section, for approval, a State plan shall include the reporting and recordkeeping requirements listed in §60.58c(b) through (g) of subpart Ec of this part.

(1) For a designated facility as defined in §60.32e(a)(1) subject to emissions limits under §60.33e(a)(1) or (b)(1), excluding §60.58c(b)(2)(ii) (fugitive emissions), (b)(2)(viii) (NOX reagent), (b)(2)(xvii) (air pollution control device inspections), (b)(2)(xviii) (bag leak detection system alarms), (b)(2)(xix) (CO CEMS data), and (b)(7) (siting documentation).

(2) For a designated facility as defined in §60.32e(a)(1) or (a)(2) subject to emissions limits under §60.33e(a)(2), (a)(3), or (b)(2), excluding §60.58c(b)(2)(xviii) (bag leak detection system alarms), (b)(2)(xix) (CO CEMS data), and (b)(7) (siting documentation).

(b) For approval, a State plan shall require the owner or operator of each HMIWI subject to the emissions limits under §60.33e to:

(1) As specified in §60.36e, maintain records of the annual equipment inspections that are required for each HMIWI subject to the emissions limits under §60.33e(a)(2), (a)(3), and (b), and the annual air pollution control device inspections that are required for each HMIWI subject to the emissions limits under §60.33e(a)(2), (a)(3), and (b)(2), any required maintenance, and any repairs not completed within 10 days of an inspection or the timeframe established by the State regulatory agency; and

(2) Submit an annual report containing information recorded under paragraph (b)(1) of this section no later than 60 days following the year in which data were collected. Subsequent reports shall be sent no later than 12 calendar months following the previous report (once the unit is subject to permitting requirements under Title V of the Act, the owner or operator must submit these reports semiannually). The report shall be signed by the facilities manager.

[60 FR 65414, Dec. 19, 1995, as amended at 74 FR 51404, Oct. 6, 2009]

§60.39e   Compliance times.

(a) Each State in which a designated facility is operating shall submit to the Administrator a plan to implement and enforce the emissions guidelines as specified in paragraphs (a)(1) and (a)(2) of this section:

(1) Not later than September 15, 1998, for the emissions guidelines as promulgated on September 15, 1997.

(2) Not later than October 6, 2010, for the emissions guidelines as amended on October 6, 2009.

(b) Except as provided in paragraphs (c) and (d) of this section, State plans shall provide that designated facilities comply with all requirements of the State plan on or before the date 1 year after EPA approval of the State plan, regardless of whether a designated facility is identified in the State plan inventory required by §60.25(a) of subpart B of this part.

(c) State plans that specify measurable and enforceable incremental steps of progress towards compliance for designated facilities planning to install the necessary air pollution control equipment may allow compliance on or before the date 3 years after EPA approval of the State plan (but not later than September 16, 2002), for the emissions guidelines as promulgated on September 15, 1997, and on or before the date 3 years after approval of an amended State plan (but not later than October 6, 2014), for the emissions guidelines as amended on October 6, 2009). Suggested measurable and enforceable activities to be included in State plans are:

(1) Date for submitting a petition for site-specific operating parameters under §60.56c(j) of subpart Ec of this part.

(2) Date for obtaining services of an architectural and engineering firm regarding the air pollution control device(s);

(3) Date for obtaining design drawings of the air pollution control device(s);

(4) Date for ordering the air pollution control device(s);

(5) Date for obtaining the major components of the air pollution control device(s);

(6) Date for initiation of site preparation for installation of the air pollution control device(s);

(7) Date for initiation of installation of the air pollution control device(s);

(8) Date for initial startup of the air pollution control device(s); and

(9) Date for initial compliance test(s) of the air pollution control device(s).

(d) State plans that include provisions allowing designated facilities to petition the State for extensions beyond the compliance times required in paragraph (b) of this section shall:

(1) Require that the designated facility requesting an extension submit the following information in time to allow the State adequate time to grant or deny the extension within 1 year after EPA approval of the State plan:

(i) Documentation of the analyses undertaken to support the need for an extension, including an explanation of why up to 3 years after EPA approval of the State plan is sufficient time to comply with the State plan while 1 year after EPA approval of the State plan is not sufficient. The documentation shall also include an evaluation of the option to transport the waste offsite to a commercial medical waste treatment and disposal facility on a temporary or permanent basis; and

(ii) Documentation of measurable and enforceable incremental steps of progress to be taken towards compliance with the emission guidelines.

(2) Include procedures for granting or denying the extension; and

(3) If an extension is granted, require expeditious compliance with the emissions guidelines on or before the date 3 years after EPA approval of the state plan (but not later than September 16, 2002), for the emissions guidelines as promulgated on September 15, 1997, and on or before the date 3 years after EPA approval of an amended state plan (but not later than October 6, 2014), for the emissions guidelines as amended on October 6, 2009.

(e) For approval, a State plan shall require compliance with §60.34e—Operator training and qualification guidelines and §60.36e—Inspection guidelines by the date 1 year after EPA approval of a State plan.

(f) The Administrator shall develop, implement, and enforce a plan for existing HMIWI located in any State that has not submitted an approvable plan within 2 years after September 15, 1997, for the emissions guidelines as promulgated on September 15, 1997, and within 2 years after October 6, 2009 for the emissions guidelines as amended on October 6, 2009. Such plans shall ensure that each designated facility is in compliance with the provisions of this subpart no later than 5 years after September 15, 1997, for the emissions guidelines as promulgated on September 15, 1997, and no later than 5 years after October 6, 2009 for the emissions guidelines as amended on October 6, 2009.

[60 FR 65414, Dec. 19, 1995, as amended at 74 FR 51404, Oct. 6, 2009; 76 FR 18412, Apr. 4, 2011]

Table 1A to Subpart Ce of Part 60—Emissions Limits for Small, Medium, and Large HMIWI at Designated Facilities as Defined in §60.32e(a)(1)

PollutantUnits (7 percent oxygen, dry basis)Emissions limitsAveraging time1Method for demonstrating compliance2
HMIWI size
SmallMediumLarge
Particulate matterMilligrams per dry standard cubic meter (mg/dscm) (grains per dry standard cubic foot (gr/dscf))115 (0.05)69 (0.03)34 (0.015)3-run average (1-hour minimum sample time per run)EPA Reference Method 5 of appendix A-3 of part 60, or EPA Reference Method 26A or 29 of appendix A-8 of part 60.
Carbon monoxideParts per million by volume (ppmv)4040403-run average (1-hour minimum sample time per run)EPA Reference Method 10 or 10B of appendix A-4 of part 60.
Dioxins/furansNanograms per dry standard cubic meter total dioxins/furans (ng/dscm) (grains per billion dry standard cubic feet (gr/109 dscf)) or ng/dscm TEQ (gr/109 dscf)125 (55) or 2.3 (1.0)125 (55) or 2.3 (1.0)125 (55) or 2.3 (1.0)3-run average (4-hour minimum sample time per run)EPA Reference Method 23 of appendix A-7 of part 60.
Hydrogen chlorideppmv or percent reduction100 or 93%100 or 93%100 or 93%3-run average (1-hour minimum sample time per run)EPA Reference Method 26 or 26A of appendix A-8 of part 60.
Sulfur dioxideppmv5555553-run average (1-hour minimum sample time per run)EPA Reference Method 6 or 6C of appendix A-4 of part 60.
Nitrogen oxidesppmv2502502503-run average (1-hour minimum sample time per run)EPA Reference Method 7 or 7E of appendix A-4 of part 60.
Leadmg/dscm (grains per thousand dry standard cubic feet (gr/103 dscf)) or percent reduction1.2 (0.52) or 70%1.2 (0.52) or 70%1.2 (0.52) or 70%3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.
Cadmiummg/dscm (gr/103 dscf) or percent reduction0.16 (0.07) or 65%0.16 (0.07) or 65%0.16 (0.07) or 65%3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.
Mercurymg/dscm (gr/103 dscf) or percent reduction0.55 (0.24) or 85%0.55 (0.24) or 85%0.55 (0.24) or 85%3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.

1Except as allowed under §60.56c(c) for HMIWI equipped with CEMS.

2Does not include CEMS and approved alternative non-EPA test methods allowed under §60.56c(b).

[60 FR 65414, Dec. 19, 1995, as amended at 74 FR 51405, Oct. 6, 2009; 76 FR 18412, Apr. 4, 2011]

Table 1B to Subpart Ce of Part 60—Emissions Limits for Small, Medium, and Large HMIWI at Designated Facilities as Defined in §60.32e(a)(1) and (a)(2)

PollutantUnits
(7 percent oxygen, dry basis)
Emissions limitsAveraging time1Method for demonstrating compliance2
HMIWI size
SmallMediumLarge
Particulate matterMilligrams per dry standard cubic meter (mg/dscm) (grains per dry standard cubic foot (gr/dscf))66 (0.029)46 (0.020)25 (0.011)3-run average (1-hour minimum sample time per run)EPA Reference Method 5 of appendix A-3 of part 60, or EPA Reference Method 26A or 29 of appendix A-8 of part 60.
Carbon monoxideParts per million by volume (ppmv)205.5113-run average (1-hour minimum sample time per run)EPA Reference Method 10 or 10B of appendix A-4 of part 60.
Dioxins/furansNanograms per dry standard cubic meter total dioxins/furans (ng/dscm) (grains per billion dry standard cubic feet (gr/109 dscf)) or ng/dscm TEQ (gr/109 dscf)16 (7.0) or 0.013 (0.0057)0.85 (0.37) or 0.020 (0.0087)9.3 (4.1) or 0.054 (0.024)3-run average (4-hour minimum sample time per run)EPA Reference Method 23 of appendix A-7 of part 60.
Hydrogen chlorideppmv447.76.63-run average (1-hour minimum sample time per run)EPA Reference Method 26 or 26A of appendix A-8 of part 60.
Sulfur dioxideppmv4.24.29.03-run average (1-hour minimum sample time per run)EPA Reference Method 6 or 6C of appendix A-4 of part 60.
Nitrogen oxidesppmv1901901403-run average (1-hour minimum sample time per run)EPA Reference Method 7 or 7E of appendix A-4 of part 60.
Leadmg/dscm (grains per thousand dry standard cubic feet (gr/103 dscf))0.31 (0.14)0.018 (0.0079)0.036 (0.016)3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.
Cadmiummg/dscm (gr/103 dscf)0.017 (0.0074)0.013 (0.0057)0.0092 (0.0040)3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.
Mercurymg/dscm (gr/103 dscf)0.014 (0.0061)0.025 (0.011)0.018 (0.0079)3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.

1Except as allowed under §60.56c(c) for HMIWI equipped with CEMS.

2Does not include CEMS and approved alternative non-EPA test methods allowed under §60.56c(b).

[74 FR 51406, Oct. 6, 2009]

Table 2A to Subpart Ce of Part 60—Emissions Limits for Small HMIWI Which Meet the Criteria Under §60.33e(b)(1)

PollutantUnits
(7 percent oxygen, dry basis)
HMIWI emissions limitsAveraging time1Method for demonstrating compliance2
Particulate mattermg/dscm (gr/dscf)197 (0.086)3-run average (1-hour minimum sample time per run)EPA Reference Method 5 of appendix A-3 of part 60, or EPA Reference Method 26A or 29 of appendix A-8 of part 60.
Carbon monoxideppmv403-run average (1-hour minimum sample time per run)EPA Reference Method 10 or 10B of appendix A-4 of part 60.
Dioxins/furansng/dscm total dioxins/furans (gr/109 dscf) or ng/dscm TEQ (gr/109 dscf)800 (350) or 15 (6.6)3-run average (4-hour minimum sample time per run)EPA Reference Method 23 of appendix A-7 of part 60.
Hydrogen chlorideppmv3,1003-run average (1-hour minimum sample time per run)EPA Reference Method 26 or 26A of appendix A-8 of part 60.
Sulfur dioxideppmv553-run average (1-hour minimum sample time per run)EPA Reference Method 6 or 6C of appendix A-4 of part 60.
Nitrogen oxidesppmv2503-run average (1-hour minimum sample time per run)EPA Reference Method 7 or 7E of appendix A-4 of part 60.
Leadmg/dscm (gr/103 dscf)10 (4.4)3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.
Cadmiummg/dscm (gr/103 dscf)4 (1.7)3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.
Mercurymg/dscm (gr/103 dscf)7.5 (3.3)3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.

1Except as allowed under §60.56c(c) for HMIWI equipped with CEMS.

2Does not include CEMS and approved alternative non-EPA test methods allowed under §60.56c(b).

[74 FR 51407, Oct. 6, 2009]

Table 2B to Subpart Ce of Part 60—Emissions Limits for Small HMIWI Which Meet the Criteria Under §60.33e(b)(2)

PollutantUnits
(7 percent oxygen, dry basis)
HMIWI Emissions limitsAveraging time1Method for demonstrating compliance2
Particulate mattermg/dscm (gr/dscf)87 (0.038)3-run average (1-hour minimum sample time per run)EPA Reference Method 5 of appendix A-3 of part 60, or EPA Reference Method 26A or 29 of appendix A-8 of part 60.
Carbon monoxideppmv203-run average (1-hour minimum sample time per run)EPA Reference Method 10 or 10B of appendix A-4 of part 60.
Dioxins/furansng/dscm total dioxins/furans (gr/109 dscf) or ng/dscm TEQ (gr/109 dscf)240 (100) or 5.1 (2.2)3-run average (4-hour minimum sample time per run)EPA Reference Method 23 of appendix A-7 of part 60.
Hydrogen chlorideppmv8103-run average (1-hour minimum sample time per run)EPA Reference Method 26 or 26A of appendix A-8 of part 60.
Sulfur dioxideppmv553-run average (1-hour minimum sample time per run)EPA Reference Method 6 or 6C of appendix A-4 of part 60.
Nitrogen oxidesppmv1303-run average (1-hour minimum sample time per run)EPA Reference Method 7 or 7E of appendix A-4 of part 60.
Leadmg/dscm (gr/103 dscf)0.50 (0.22)3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.
Cadmiummg/dscm (gr/103 dscf)0.11 (0.048)3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.
Mercurymg/dscm (gr/103 dscf)0.0051 (0.0022)3-run average (1-hour minimum sample time per run)EPA Reference Method 29 of appendix A-8 of part 60.

1Except as allowed under §60.56c(c) for HMIWI equipped with CEMS.

2Does not include CEMS and approved alternative non-EPA test methods allowed under §60.56c(b).

[74 FR 51407, Oct. 6, 2009]

Subpart D—Standards of Performance for Fossil-Fuel-Fired Steam Generators

Source: 72 FR 32717, June 13, 2007, unless otherwise noted.

§60.40   Applicability and designation of affected facility.

(a) The affected facilities to which the provisions of this subpart apply are:

(1) Each fossil-fuel-fired steam generating unit of more than 73 megawatts (MW) heat input rate (250 million British thermal units per hour (MMBtu/hr)).

(2) Each fossil-fuel and wood-residue-fired steam generating unit capable of firing fossil fuel at a heat input rate of more than 73 MW (250 MMBtu/hr).

(b) Any change to an existing fossil-fuel-fired steam generating unit to accommodate the use of combustible materials, other than fossil fuels as defined in this subpart, shall not bring that unit under the applicability of this subpart.

(c) Except as provided in paragraph (d) of this section, any facility under paragraph (a) of this section that commenced construction or modification after August 17, 1971, is subject to the requirements of this subpart.

(d) The requirements of §§60.44 (a)(4), (a)(5), (b) and (d), and 60.45(f)(4)(vi) are applicable to lignite-fired steam generating units that commenced construction or modification after December 22, 1976.

(e) Any facility subject to either subpart Da or KKKK of this part is not subject to this subpart.

[72 FR 32717, June 13, 2007, as amended at 77 FR 9447, Feb. 16, 2012]

§60.41   Definitions.

As used in this subpart, all terms not defined herein shall have the meaning given them in the Act, and in subpart A of this part.

Boiler operating day means a 24-hour period between 12 midnight and the following midnight during which any fuel is combusted at any time in the steam-generating unit. It is not necessary for fuel to be combusted the entire 24-hour period.

Coal means all solid fuels classified as anthracite, bituminous, subbituminous, or lignite by ASTM D388 (incorporated by reference, see §60.17).

Coal refuse means waste-products of coal mining, cleaning, and coal preparation operations (e.g. culm, gob, etc.) containing coal, matrix material, clay, and other organic and inorganic material.

Fossil fuel means natural gas, petroleum, coal, and any form of solid, liquid, or gaseous fuel derived from such materials for the purpose of creating useful heat.

Fossil fuel and wood residue-fired steam generating unit means a furnace or boiler used in the process of burning fossil fuel and wood residue for the purpose of producing steam by heat transfer.

Fossil-fuel-fired steam generating unit means a furnace or boiler used in the process of burning fossil fuel for the purpose of producing steam by heat transfer.

Natural gas means a fluid mixture of hydrocarbons (e.g., methane, ethane, or propane), composed of at least 70 percent methane by volume or that has a gross calorific value between 35 and 41 megajoules (MJ) per dry standard cubic meter (950 and 1,100 Btu per dry standard cubic foot), that maintains a gaseous state under ISO conditions. In addition, natural gas contains 20.0 grains or less of total sulfur per 100 standard cubic feet. Finally, natural gas does not include the following gaseous fuels: landfill gas, digester gas, refinery gas, sour gas, blast furnace gas, coal-derived gas, producer gas, coke oven gas, or any gaseous fuel produced in a process which might result in highly variable sulfur content or heating value.

Wood residue means bark, sawdust, slabs, chips, shavings, mill trim, and other wood products derived from wood processing and forest management operations.

[72 FR 32717, June 13, 2007, as amended at 77 FR 9447, Feb. 16, 2012]

§60.42   Standard for particulate matter (PM).

(a) Except as provided under paragraphs (b), (c), (d), and (e) of this section, on and after the date on which the performance test required to be conducted by §60.8 is completed, no owner or operator subject to the provisions of this subpart shall cause to be discharged into the atmosphere from any affected facility any gases that:

(1) Contain PM in excess of 43 nanograms per joule (ng/J) heat input (0.10 lb/MMBtu) derived from fossil fuel or fossil fuel and wood residue.

(2) Exhibit greater than 20 percent opacity except for one six-minute period per hour of not more than 27 percent opacity.

(b)(1) On or after December 28, 1979, no owner or operator shall cause to be discharged into the atmosphere from the Southwestern Public Service Company's Harrington Station #1, in Amarillo, TX, any gases which exhibit greater than 35 percent opacity, except that a maximum or 42 percent opacity shall be permitted for not more than 6 minutes in any hour.

(2) Interstate Power Company shall not cause to be discharged into the atmosphere from its Lansing Station Unit No. 4 in Lansing, IA, any gases which exhibit greater than 32 percent opacity, except that a maximum of 39 percent opacity shall be permitted for not more than six minutes in any hour.

(c) As an alternate to meeting the requirements of paragraph (a) of this section, an owner or operator that elects to install, calibrate, maintain, and operate a continuous emissions monitoring systems (CEMS) for measuring PM emissions can petition the Administrator (in writing) to comply with §60.42Da(a) of subpart Da of this part. If the Administrator grants the petition, the source will from then on (unless the unit is modified or reconstructed in the future) have to comply with the requirements in §60.42Da(a) of subpart Da of this part.

(d) An owner or operator of an affected facility that combusts only natural gas is exempt from the PM and opacity standards specified in paragraph (a) of this section.

(e) An owner or operator of an affected facility that combusts only gaseous or liquid fossil fuel (excluding residual oil) with potential SO2 emissions rates of 26 ng/J (0.060 lb/MMBtu) or less and that does not use post-combustion technology to reduce emissions of SO2 or PM is exempt from the PM standards specified in paragraph (a) of this section.

[60 FR 65415, Dec. 19, 1995, as amended at 76 FR 3522, Jan. 20, 2011; 74 FR 5077, Jan. 28, 2009; 77 FR 9447, Feb. 16, 2012]

§60.43   Standard for sulfur dioxide (SO2).

(a) Except as provided under paragraph (d) of this section, on and after the date on which the performance test required to be conducted by §60.8 is completed, no owner or operator subject to the provisions of this subpart shall cause to be discharged into the atmosphere from any affected facility any gases that contain SO2 in excess of:

(1) 340 ng/J heat input (0.80 lb/MMBtu) derived from liquid fossil fuel or liquid fossil fuel and wood residue.

(2) 520 ng/J heat input (1.2 lb/MMBtu) derived from solid fossil fuel or solid fossil fuel and wood residue, except as provided in paragraph (e) of this section.

(b) Except as provided under paragraph (d) of this section, when different fossil fuels are burned simultaneously in any combination, the applicable standard (in ng/J) shall be determined by proration using the following formula:

eCFR graphic er13jn07.000.gif

View or download PDF

Where:

PSSO2 = Prorated standard for SO2 when burning different fuels simultaneously, in ng/J heat input derived from all fossil fuels or from all fossil fuels and wood residue fired;

y = Percentage of total heat input derived from liquid fossil fuel; and

z = Percentage of total heat input derived from solid fossil fuel.

(c) Compliance shall be based on the total heat input from all fossil fuels burned, including gaseous fuels.

(d) As an alternate to meeting the requirements of paragraphs (a) and (b) of this section, an owner or operator can petition the Administrator (in writing) to comply with §60.43Da(i)(3) of subpart Da of this part or comply with §60.42b(k)(4) of subpart Db of this part, as applicable to the affected source. If the Administrator grants the petition, the source will from then on (unless the unit is modified or reconstructed in the future) have to comply with the requirements in §60.43Da(i)(3) of subpart Da of this part or §60.42b(k)(4) of subpart Db of this part, as applicable to the affected source.

(e) Units 1 and 2 (as defined in appendix G of this part) at the Newton Power Station owned or operated by the Central Illinois Public Service Company will be in compliance with paragraph (a)(2) of this section if Unit 1 and Unit 2 individually comply with paragraph (a)(2) of this section or if the combined emission rate from Units 1 and 2 does not exceed 470 ng/J (1.1 lb/MMBtu) combined heat input to Units 1 and 2.

[60 FR 65415, Dec. 19, 1995, as amended at 74 FR 5077, Jan. 28, 2009]

§60.44   Standard for nitrogen oxides (NOX).

(a) Except as provided under paragraph (e) of this section, on and after the date on which the performance test required to be conducted by §60.8 is completed, no owner or operator subject to the provisions of this subpart shall cause to be discharged into the atmosphere from any affected facility any gases that contain NOX, expressed as NO2 in excess of:

(1) 86 ng/J heat input (0.20 lb/MMBtu) derived from gaseous fossil fuel.

(2) 129 ng/J heat input (0.30 lb/MMBtu) derived from liquid fossil fuel, liquid fossil fuel and wood residue, or gaseous fossil fuel and wood residue.

(3) 300 ng/J heat input (0.70 lb/MMBtu) derived from solid fossil fuel or solid fossil fuel and wood residue (except lignite or a solid fossil fuel containing 25 percent, by weight, or more of coal refuse).

(4) 260 ng/J heat input (0.60 lb MMBtu) derived from lignite or lignite and wood residue (except as provided under paragraph (a)(5) of this section).

(5) 340 ng/J heat input (0.80 lb MMBtu) derived from lignite which is mined in North Dakota, South Dakota, or Montana and which is burned in a cyclone-fired unit.

(b) Except as provided under paragraphs (c), (d), and (e) of this section, when different fossil fuels are burned simultaneously in any combination, the applicable standard (in ng/J) is determined by proration using the following formula:

eCFR graphic er13jn07.001.gif

View or download PDF

Where:

PSNOX = Prorated standard for NOX when burning different fuels simultaneously, in ng/J heat input derived from all fossil fuels fired or from all fossil fuels and wood residue fired;

w = Percentage of total heat input derived from lignite;

x = Percentage of total heat input derived from gaseous fossil fuel;

y = Percentage of total heat input derived from liquid fossil fuel; and

z = Percentage of total heat input derived from solid fossil fuel (except lignite).

(c) When a fossil fuel containing at least 25 percent, by weight, of coal refuse is burned in combination with gaseous, liquid, or other solid fossil fuel or wood residue, the standard for NOX does not apply.

(d) Except as provided under paragraph (e) of this section, cyclone-fired units which burn fuels containing at least 25 percent of lignite that is mined in North Dakota, South Dakota, or Montana remain subject to paragraph (a)(5) of this section regardless of the types of fuel combusted in combination with that lignite.

(e) As an alternate to meeting the requirements of paragraphs (a), (b), and (d) of this section, an owner or operator can petition the Administrator (in writing) to comply with §60.44Da(e)(3) of subpart Da of this part. If the Administrator grants the petition, the source will from then on (unless the unit is modified or reconstructed in the future) have to comply with the requirements in §60.44Da(e)(3) of subpart Da of this part.

§60.45   Emissions and fuel monitoring.

(a) Each owner or operator of an affected facility subject to the applicable emissions standard shall install, calibrate, maintain, and operate continuous opacity monitoring system (COMS) for measuring opacity and a continuous emissions monitoring system (CEMS) for measuring SO2 emissions, NOX emissions, and either oxygen (O2) or carbon dioxide (CO2) except as provided in paragraph (b) of this section.

(b) Certain of the CEMS and COMS requirements under paragraph (a) of this section do not apply to owners or operators under the following conditions:

(1) For a fossil-fuel-fired steam generator that combusts only gaseous or liquid fossil fuel (excluding residual oil) with potential SO2 emissions rates of 26 ng/J (0.060 lb/MMBtu) or less and that does not use post-combustion technology to reduce emissions of SO2 or PM, COMS for measuring the opacity of emissions and CEMS for measuring SO2 emissions are not required if the owner or operator monitors SO2 emissions by fuel sampling and analysis or fuel receipts.

(2) For a fossil-fuel-fired steam generator that does not use a flue gas desulfurization device, a CEMS for measuring SO2 emissions is not required if the owner or operator monitors SO2 emissions by fuel sampling and analysis.

(3) Notwithstanding §60.13(b), installation of a CEMS for NOX may be delayed until after the initial performance tests under §60.8 have been conducted. If the owner or operator demonstrates during the performance test that emissions of NOX are less than 70 percent of the applicable standards in §60.44, a CEMS for measuring NOX emissions is not required. If the initial performance test results show that NOX emissions are greater than 70 percent of the applicable standard, the owner or operator shall install a CEMS for NOX within one year after the date of the initial performance tests under §60.8 and comply with all other applicable monitoring requirements under this part.

(4) If an owner or operator is not required to and elects not to install any CEMS for either SO2 or NOX, a CEMS for measuring either O2 or CO2 is not required.

(5) For affected facilities using a PM CEMS, a bag leak detection system to monitor the performance of a fabric filter (baghouse) according to the most current requirements in §60.48Da of this part, or an ESP predictive model to monitor the performance of the ESP developed in accordance and operated according to the most current requirements in section §60.48Da of this part a COMS is not required.

(6) A COMS for measuring the opacity of emissions is not required for an affected facility that does not use post-combustion technology (except a wet scrubber) for reducing PM, SO2, or carbon monoxide (CO) emissions, burns only gaseous fuels or fuel oils that contain less than or equal to 0.30 weight percent sulfur, and is operated such that emissions of CO to the atmosphere from the affected source are maintained at levels less than or equal to 0.15 lb/MMBtu on a boiler operating day average basis. Owners and operators of affected sources electing to comply with this paragraph must demonstrate compliance according to the procedures specified in paragraphs (b)(6)(i) through (iv) of this section.

(i) You must monitor CO emissions using a CEMS according to the procedures specified in paragraphs (b)(6)(i)(A) through (D) of this section.

(A) The CO CEMS must be installed, certified, maintained, and operated according to the provisions in §60.58b(i)(3) of subpart Eb of this part.

(B) Each 1-hour CO emissions average is calculated using the data points generated by the CO CEMS expressed in parts per million by volume corrected to 3 percent oxygen (dry basis).

(C) At a minimum, valid 1-hour CO emissions averages must be obtained for at least 90 percent of the operating hours on a 30-day rolling average basis. The 1-hour averages are calculated using the data points required in §60.13(h)(2).

(D) Quarterly accuracy determinations and daily calibration drift tests for the CO CEMS must be performed in accordance with procedure 1 in appendix F of this part.

(ii) You must calculate the 1-hour average CO emissions levels for each boiler operating day by multiplying the average hourly CO output concentration measured by the CO CEMS times the corresponding average hourly flue gas flow rate and divided by the corresponding average hourly heat input to the affected source. The 24-hour average CO emission level is determined by calculating the arithmetic average of the hourly CO emission levels computed for each boiler operating day.

(iii) You must evaluate the preceding 24-hour average CO emission level each boiler operating day excluding periods of affected source startup, shutdown, or malfunction. If the 24-hour average CO emission level is greater than 0.15 lb/MMBtu, you must initiate investigation of the relevant equipment and control systems within 24 hours of the first discovery of the high emission incident and, take the appropriate corrective action as soon as practicable to adjust control settings or repair equipment to reduce the 24-hour average CO emission level to 0.15 lb/MMBtu or less.

(iv) You must record the CO measurements and calculations performed according to paragraph (b)(6) of this section and any corrective actions taken. The record of corrective action taken must include the date and time during which the 24-hour average CO emission level was greater than 0.15 lb/MMBtu, and the date, time, and description of the corrective action.

(7) An owner or operator of an affected facility subject to an opacity standard under §60.42 that elects to not use a COMS because the affected facility burns only fuels as specified under paragraph (b)(1) of this section, monitors PM emissions as specified under paragraph (b)(5) of this section, or monitors CO emissions as specified under paragraph (b)(6) of this section, shall conduct a performance test using Method 9 of appendix A-4 of this part and the procedures in §60.11 to demonstrate compliance with the applicable limit in §60.42 by April 29, 2011 or within 45 days after stopping use of an existing COMS, whichever is later, and shall comply with either paragraph (b)(7)(i), (b)(7)(ii), or (b)(7)(iii) of this section. The observation period for Method 9 of appendix A-4 of this part performance tests may be reduced from 3 hours to 60 minutes if all 6-minute averages are less than 10 percent and all individual 15-second observations are less than or equal to 20 percent during the initial 60 minutes of observation. The permitting authority may exempt owners or operators of affected facilities burning only natural gas from the opacity monitoring requirements.

(i) Except as provided in paragraph (b)(7)(ii) or (b)(7)(iii) of this section, the owner or operator shall conduct subsequent Method 9 of appendix A-4 of this part performance tests using the procedures in paragraph (b)(7) of this section according to the applicable schedule in